Turn 'em all on: WSJT_HAMLIB_TRACE WSJT_HAMLIB_VERBOSE_TRACE WSJT_TRACE_CAT WSJT_TRACE_CAT_POLLS
It sounds like it is colliding with another command that is still "in work" and the retry period is too short at 200ms. That will give 3 seconds instead of 600ms total time. Can you compile hamlib too? If so change the timeout to 1000 in ts480.c and see if that makes a difference. It's getting the "?" reply which can mean busy or command invalid and the command is valid so the rig is busy doing something else. 73 Mike W9MDB -----Original Message----- From: Steven Franke [mailto:s.j.fra...@icloud.com] Sent: Wednesday, July 08, 2015 1:44 PM To: WSJT software development Subject: [wsjt-devel] r5700 Bill, I just updated back to r5700 and the problem that I described yesterday occurred after the first transmission. I captured the following from the trace file: Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Unknown command or rig busy 'FA00024924600' Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Retrying shortly Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Unknown command or rig busy 'FA00024924600' Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Retrying shortly Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Unknown command or rig busy 'FA00024924600' Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Retrying shortly Wed Jul 8 18:35:53 2015 GMT(/home/radio/Builds/wsjtx/HamlibTransceiver.cpp:41)Critical: Hamlib: kenwood_transaction: Unknown command or rig busy 'FA00024924600' This time (and one of the 4 times that I observed this yesterday) there was no dialog box. The other 3 times, a dialog box appeared, asking me if I wanted to re-configure the radio. In all 5 cases, TX Enable turned from red to white. In the two cases when the dialog box failed to appear, the rig continued to hop in receive mode. In the cases when the dialog box appeared, the rig stopped changing bands, whereas the software continued to “hop”. Would it be more helpful if I switch on “WSJT_TRACE_CAT_POLLS”? Note that I have not updated hamlib recently. Steve k9an ------------------------------------------------------------------------------ Don't Limit Your Business. Reach for the Cloud. GigeNET's Cloud Solutions provide you with the tools and support that you need to offload your IT needs and focus on growing your business. Configured For All Businesses. Start Your Cloud Today. https://www.gigenetcloud.com/ _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel ------------------------------------------------------------------------------ Don't Limit Your Business. Reach for the Cloud. GigeNET's Cloud Solutions provide you with the tools and support that you need to offload your IT needs and focus on growing your business. Configured For All Businesses. Start Your Cloud Today. https://www.gigenetcloud.com/ _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
