You need to run WSJT-X using Hamlib NET rigctl and re-run this until it fails.
de Mike W9MDB
From: Pino Zollo <[email protected]>
To: [email protected]
Sent: Tuesday, February 28, 2017 4:53 PM
Subject: [wsjt-devel] IC-7300 USB-D -> IC-7300 control lost
El 28/02/17 a las 15:45, [email protected] escribió:
> Can you run using rigctld-wsjtx with -vvvvv and send me the log output?
> ?Capture the output with typescript for example?
> Not sure if the IC7300 has had a lot of testing on WSJT-X.You do, of course,
> want to operate with a wide bandwidth so have you customized the filters at
> all?
> de Mike W9MDB
Hi Mike,
Hope that this might help:
-------------------
pino@Radio3:~$ /usr/local/bin/rigctld-wsjtx -m 373 -c 0x94 -s 9600 -vvvvvv
rigctld, Hamlib 3.1~git
Report bugs to <[email protected]>
rig:rig_init called
icom: _init called
rig_register (355)
rig_register (309)
rig_register (310)
rig_register (311)
rig_register (313)
rig_register (314)
rig_register (315)
rig_register (319)
rig_register (320)
rig_register (321)
rig_register (322)
rig_register (367)
rig_register (323)
rig_register (346)
rig_register (324)
rig_register (328)
rig_register (330)
rig_register (326)
rig_register (327)
rig_register (347)
rig_register (357)
rig_register (363)
rig_register (329)
rig_register (362)
rig_register (345)
rig_register (356)
rig_register (360)
rig_register (370)
rig_register (361)
rig_register (373)
rig_register (331)
rig_register (312)
rig_register (316)
rig_register (332)
rig_register (334)
rig_register (344)
rig_register (368)
rig_register (335)
rig_register (369)
rig_register (336)
rig_register (358)
rig_register (337)
rig_register (338)
rig_register (339)
rig_register (340)
rig_register (341)
rig_register (342)
rig_register (343)
rig_register (366)
rig_register (303)
rig_register (304)
rig_register (306)
rig_register (307)
rig_register (302)
rig_register (352)
rig_register (353)
rig_register (351)
rig_register (364)
rig_register (365)
rig_register (354)
rig_register (371)
rig_register (372)
icom_init: civ_version=1
rig_set_conf: civaddr='0x94'
rig:rig_open called
Opened rig model 373, 'IC-7300'
Backend version: 0.7.2, Status: Stable
---------------------------------------------
I have found a solution to get stabe USB-D mode.....it was into the
configuration of WSJT-x...
The real problem is that after few minutes WSJT-X looses the control and
open a window say if I want retry or abandon ...
Also the audio input disappears and the waterfall becomes empty.
Also with fldigi I run in similar problems using RigCAT.
Best 73
Pino ZP4KFX
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
