You want USB-D -- i.e. Data Mode. The 7300 will not receive digital audio
unless in data mode.
You can set Data/Pkt mode in WSJT-X Setttings/Radio and that should make it
automatic.
de Mike W9MDB
On Sunday, June 24, 2018, 4:03:21 PM CDT, Jeffrey Weinberg
<[email protected]> wrote:
- Program version: 1.9.1 r8747
- Operating system: Windows 10 Pro, 10.0.17134 Build 17134
- Concise description of the problem: WSJT-X will place my Icom IC-7300 into
transmit mode but will not transmit any data. Antenna connection is good and
properly adjusted for low SWR. No data is transmitted on any band.
- Exact sequence of steps required to reproduce the problem: Double-click on
a FT-8 or JT-65 station received. BTW, the program is receiving beautifully. No
issues. Try to contact the station. IC-7300 goes into transmit mode, but
waterfall display shows nothing being transmitted, just a carrier. I have yet
to make a contact, even with the strongest stations. I have checked the driver
settings. The driver was downloaded from Icom prior to connecting the radio to
the computer.Driver is Silicon Labs CP210x USB to UART Bridge. On my system, it
happens to be on COM5. Port settings are 9600 baud, 8 data bits, no parity, 1
stop bit, no flow control.Program settings are: Rig: IC-7300, CAT Control
Serial Port: COM5, Baud Rate: 9600, Data bits: 8, Stop bits: 1, Handshake:
None, No DTR or RTS, PTT Method: CAT (COM5), Mode: None, Split Operation:
None.Test CAT: GreenTest PTT: RedAudio Input: Microphone (USB Audio CODEC),
Audio Output: Speakers (USB Audio Codec)All other settings have been configured
for callsign, grid square information, etc.Radio settings:CONNECTORS: ACC/USB
Output Select: AFACC/USB AF Output Level: 40%ACC/USB AF SQL: OFF (open)ACC/USB
AF Beep/Speech… Output: OFFACC/USB IF Output Level: 50%ACC MOD Level: 50%USB
MOD Level: 40%DATA OFF MODE: MIC,ACCDATA MOD: USBUSB Serial Function: CI-VUSB
SEND: OFFUSB Keying (CW): OFFUSB Keying (RTTY): OFF
CI-V Baud Rate: 9600CI-V Address: 94hCI-V Transceive: ONCI-V USG - REMOTE
Transceive Address: 00hCI-V Output (for ANT): OFFCI-V USB Port: Link to
[REMOTE]CI-V USB Baud Rate: 9600CI-V USB Echo Back: ON
Again, everything in the program appears to be functioning normally except no
data is being transmitted, but the transmitter is properly going into transmit
mode, and the Test PTT test button is red and not green.
Thank you for your help. I have been trying to figure this out by going to a
variety of Internet sources, but without any luck. Also, your Yahoo support
group appears to be non-existent. I tried sending this issue to them in an
e-mail, but it was returned as undeliverable.
Jeff [email protected]
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org!
http://sdm.link/slashdot_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
