FTDX-818 setup for WSJT-X (1 Watt output, -180 dB attenuators to small
dummy load antenna, ~70 ft from the EME station with IC-9700 radio at min.
output - Both with Win 10-64 bit - signal report about -7dB)
Radio
COM5
38400
Default x3
CAT
Data/Pkt
Fake it
----------------------------------
Audio
Input: Internal Microphone (Conexant ISST Audio) - Mono
Output: Speakers (USB Audio CODEC) - Mono
---------------------------------
Sound
Recording: Microphone - USB Audio CODEC - Default device
Payback: Speakers - Conexant ISST Audio - Default Device
Speakers - USB Audio CODEC - Default Communication DEvice
----------------------------------
IC-9700 setup WSJT-X
Radio
AMSAT-UK FUNcube Dongle Pro
RST
COM3
Data/Pkt
Fake It
----------------------------------
Audio
Input: Line (6-FUNcube Dongle V2.0) - Left
Output: IC 9700 Playback (3-USB Audio CODEC) - Both
---------------------------------
Sound
Recording: Line - 6-FUNcube dongle V2.0 - Default Device
Playback: IC 9700 Playback - 3-USB Audio CODEC - Default Communication
Device
Scepter Q32 - Intel(R) Display Audio - Default Device
--------------------------------
with:
Radio: SoftRock Si570 AUR-USB
Soundcard Input: 1-4 (Behringer UMC404HD 195)
it crushes. Can only turn it ON again if IQ+ is OFF
==============================================================================
MAP65-Q65 rc3
MAP65 sends OK both JT65 and Q65 from IC-9700 to FTDX-818 both ways (70 ft
apart, minimum power with attenuators) and they are decoded.
With Linrad, I see signals on both vertical bars (from 35 to 55 dB on
signal being received), via and network but can't decode any signal.
Without Linrad, I couldn't set up MAP65 with IQ+ and UMC-UPHORIA UMC404HD
one day and the next day it worked fine and sended and decoded both ways.
Sometimes closing the program and restarting can solve problems.
Zedig: WinUSB (6.0.7.603 16385 for both DG85AQ-I2C and UMC404HD.
This didn't work:
Radio: Softrock Si570 AUR-USB
Soundcard input:
33 - 4 - WDM-KS 1-4 (IN 1-4)
34 - 4 - WDM-KS 1-2 (IN 1-2)
36 - 2 - WDM-KS 3-4 (IN 3-4)
all give the message: "Failed to start audio input stream".
I think it worked with previous rc1 or rc2. Again, it worked one day and
not the next day.
-----------------------------
Somewhat confused what mode is being used, JT65B or Q65B. When transmitting
both the left horizontal bar at the bottom and the JT65B are yellow in both
modes.
On WSJT-X Q65 I don't see the messages for EME like OOO and RO that are
seen with JT65 and Sh clicked on.
On MAP65 Q65 they are not there either.
---------------------------------
Overall better. I was able to do exchanges both ways with WSJT-X and MAP65
in Q65 mode.
WSJT-X way more stable than MAP65 but I need MAP65 to use my IQ+ and XPOL
antennas.
I have to work more with Linrad to get it to decode but I see the signals
on MAP65 in both vertical bars.
Hope this is of some help.
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
