Good day, I am looking for to use Xastir but not in KISS mode, therefore i am trying-it with, alternating, ArgentData's OpenTracker USB & SCS Tracker DSP/TNC. With both TNCs i have some issues which are not exactly the same, but i presume could be sort-out in the same way (see discussion bellow): does there is a way to customise or to create a script for each TNC with just the needed commands? Digging Xastir config sub-folder, i found some "tnc-startup.(tnc-name)" files in-it...
Thank you for help Début du message réexpédié : > Scott Miller [email protected] [tracker2] > Most of those TNC2 commands aren't needed and aren't supported on the OTUSB. > Presumably it's not using the proper exit commands either, but I don't know > what Xastir is trying to send on exit. If you insist on running it without > KISS mode, I would suggest rewriting Xastir's command script to use only the > commands you need. > > Scott > > On 11/25/2014 11:46 PM, F1MHV [email protected] [tracker2] wrote: >> Good morning Scott, >> >> >> I installed according to "Howto" Xastir V2.0.6. and to connect the OTUSB, i >> am using /dev/cu.usbmodemxxxx (with /dev/tty.usbmodemxxx... Xastir freeze >> immediately) and according to the log bellow, i can connect and transmit as >> well (didn't tried rx for the time being), but when i want to >> stop/disconnect from OTUSB, then Xastir freeze. Beside the OTUSB, i have the >> SCS Tracker DSP-TNC and i don't have all these errors showing in the >> connection log, only few of them, and i can stop the interface without >> freezing Xastir. >> >> You are mentioning console entries, but there are not so much setting when >> you add an "interface": >> >> - i choose "Serial TNC" >> >> >> - Then: >> >> >> Before asking Xastir, i would like to check with you and other users, if >> there is anything specific to sort-out my issues... >> >> 73 de Cyril - f1mhv - df1chb/am >> >> ps: connection log bellow >> ps2: for info, with OS X, i ma using Serialtools V1.2 (AppStore) to access >> the OTUSB with command line and it's working like a charm... >> >> " 1:TNC-> DIGI on >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> EXP on >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> Filt off >> 1:TNC-> FILTER OFF >> 1:TNC-> >> 1:TNC-> FLow off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> FUll off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> HEA off >> 1:TNC-> HEADERLN OFF >> 1:TNC-> >> 1:TNC-> LFadd off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> LFSup on >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> AUTOLF off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MCOM off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MFILT off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MON on >> 1:TNC-> MONITOR ON >> 1:TNC-> >> 1:TNC-> MResp off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MRPt on >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MSTamp off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MXMit off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> NEWmode off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> PASSALL off >> 1:TNC-> PASSALL OFF >> 1:TNC-> >> 1:TNC-> PID off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MNOAX25 off >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> PIDCHECK on >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> MPROTO OFF >> 1:TNC-> Invalid Command >> 1:TNC-> >> 1:TNC-> SCR 0 >> 1:TNC-> SCRIPT OFF >> 1:TX -> DF1CHB>APX206,WIDE2-2:=5114.00N/00648.00ExXASTIR-Darwin >> 1:TNC-> >> 1:TNC-> MYCALL DF1CHB >> 1:TNC-> MYCALL DF1CHB >> 1:TNC-> >> 1:TNC-> UNPROTO APX206 VIA WIDE2-2 >> 1:TNC-> Error >> 1:TNC-> >> 1:TNC-> k >> 1:TNC-> CTRL-C to Exit >> 1:TNC-> =5114.00N/00648.00ExXASTIR-Darwin >> 1:TX -> DF1CHB>APX206,WIDE2-2::F1MHV :testing...{0h} >> 1:TNC-> MYCALL DF1CHB >> 1:TNC-> MYCALL DF1CHB >> 1:TNC-> >> 1:TNC-> UNPROTO APX206 VIA WIDE2-2 >> 1:TNC-> Error >> 1:TNC-> >> 1:TNC-> k >> 1:TNC-> CTRL-C to Exit >> 1:TNC-> :F1MHV :testing...{0h} >> 1:TX -> DF1CHB>APX206,WIDE2-2::F1MHV :testing...{0h} >> 1:TNC-> MYCALL DF1CHB >> 1:TNC-> MYCALL DF1CHB >> 1:TNC-> >> 1:TNC-> UNPROTO APX206 VIA WIDE2-2 >> 1:TNC-> Error >> 1:TNC-> >> 1:TNC-> k >> 1:TNC-> CTRL-C to Exit >> 1:TNC-> :F1MHV :testing...{0h" >> >> Le 26 nov. 2014 à 06:10, Scott Miller [email protected] [tracker2] a écrit : >> >>> >>> >>> It *should* work if you're careful about the console entry requirements (it >>> needs a couple of carriage returns before you get a cmd: prompt) but I >>> haven't tried it in a long time. >>> >>> Scott _______________________________________________ Xastir mailing list [email protected] http://xastir.org/mailman/listinfo/xastir
