Re: [xcat-user] xCAT syncfiles issue

[Casandra H Qiu]

The fixes will be in the xcat 2.12


Thanks,
Casandra
...................................................................
Casandra Hong Qiu
Phone: (845) 433-9291, t/l 293-9291
Office: B/002, Floor 3, Z13
cxh...@us.ibm.com





From:   Qamar Nazir <qna...@ocf.co.uk>
To:     xCAT Users Mailing list <xcat-user@lists.sourceforge.net>
Date:   04/05/2016 12:15 PM
Subject:        Re: [xcat-user] xCAT syncfiles issue



Thanks Casandra,

Will this be fixed in next version?

Best Regards,



Qamar Nazir



On 04/04/16 17:44, Casandra H Qiu wrote:


      I recreated your issue in my test system.

      #Test
      /root/testfile -> /root/.
      /root/testfile.post -> /root/.
      EXECUTE:
      /root/testfile.post

      I think this maybe a bug in the code.
      1) it only execute file in the synclist file
      2) it will execute all the files in the same dir if they are defined
      in the synclist file.


      Thanks,
      Casandra
      ...................................................................
      Casandra Hong Qiu
      Phone: (845) 433-9291, t/l 293-9291
      Office: B/002, Floor 3, Z13
      cxh...@us.ibm.com



      Inactive
          hide details for Qamar Nazir ---04/04/2016 04:39:52
      AM---Hi,
          Thanks for the reply.Qamar Nazir ---04/04/2016
      04:39:52 AM---Hi, Thanks for the reply.

      From: Qamar Nazir <qna...@ocf.co.uk>
      To: xCAT Users Mailing list <xcat-user@lists.sourceforge.net>
      Date: 04/04/2016 04:39 AM
      Subject: Re: [xcat-user] xCAT syncfiles issue





      Hi,

      Thanks for the reply.
      Below is the reply I sent on 22nd of last month. It's weird that it
      didn't go through.


      Thanks for your reply.

      The synclist is attached. Please check the top lines where I have put
      'testfile' for testing. Without synchronizing the corresponding
      script, xCAT doesn't run the script at all. To get that script to run
      automatically I have to transfer the script too. I remember in
      previous xCAT releases the script transfer was not necessary (please
      correct me if I'm wrong)

      testfile.post has these contents:

      #!/bin/bash

          echo "this is a test script"

      exit 0

      When I apply the updatenode command from the Master node it returns
      these results:

      updatenode node01 -F

      node01: this is a test script
      node01: this is a test script
      File synchronization has completed for nodes.


      May be it was the attachment that is why it might have been blocked
      by the filter. Let me paste the syncfile below.

      #Test
      /root/testfile -> /root/.
      /root/testfile.post -> /root/.
      #Hostbased
      /etc/hosts.equiv -> /etc/.
      /etc/ssh/ssh_known_hosts -> /etc/ssh/.
      /etc/ssh/ssh_known_hosts -> /root/.ssh/known_hosts
      /etc/hosts -> /etc/.
      /etc/resolv.conf -> /etc/.
      /etc/passwd /etc/shadow /etc/group -> /etc/.
      #Modules
      /install/syncfiles/modules/modules.* -> /etc/profile.d/.
      /install/syncfiles/modules/custom -> /etc/.

      #Monitoring

      /etc/ganglia/gmond.conf -> /etc/ganglia/gmond.conf
      #/etc/nagios/nrpe.cfg.nsd -> /etc/nagios/.

      #Modprobe/Lustre
      /install/syncfiles/modprobe/* -> /etc/modprobe.d/.

      #Torque
      /install/syncfiles/torque/pbs_mom -> /etc/init.d/.
      /install/syncfiles/torque/trqauthd -> /etc/init.d/.
      /install/syncfiles/torque/torque.conf -> /etc/ld.so.conf.d/.

      #Routing
      /install/syncfiles/eth/route-eth0 -> /etc/sysconfig/network-scripts/.
      /install/syncfiles/eth/route-bond0 ->
      /etc/sysconfig/network-scripts/.
      /install/syncfiles/eth/route-bond0.post ->
      /etc/sysconfig/network-scripts/.

      #NRPE
      /install/syncfiles/nrpe/nrpe.cfg.nsd -> /etc/nagios/nrpe.cfg

      #multipath
      /install/syncfiles/phaseIII/nsd/multipath/multipath.conf -> /etc/.
      /install/syncfiles/phaseIII/nsd/multipath/bindings ->
      /etc/multipath/.
      /install/syncfiles/phaseIII/nsd/multipath/multipath.conf.post ->
      /etc/.
      #openib
      /install/syncfiles/etc/infiniband/openib.conf -> /etc/infiniband/.
      #
      #Authentication
      /install/syncfiles/etc/auth/*-ac -> /etc/pam.d/.
      /install/syncfiles/etc/auth/*-auth -> /etc/pam.d/.
      /install/syncfiles/etc/auth/*.conf -> /etc/.

      EXECUTE:
      /root/testfile.post
      /etc/ganglia/gmond.conf.post
      /etc/nagios/nrpe.cfg.nsd.post
      /install/syncfiles/torque/pbs_mom.post
      /install/syncfiles/torque/trqauthd.post
      /install/syncfiles/eth/route-eth0.post
      /install/syncfiles/eth/routebond0.post
      /install/syncfiles/torque/torque.conf.post
      /install/syncfiles/nrpe/nrpe.cfg.nsd.post
      /install/syncfiles/etc/multipath/multipath.conf.post
      /install/syncfiles/etc/infiniband/openib.conf.post
      /install/syncfiles/etc/auth/nslcd.conf.post
      /install/syncfiles/gpfs/kernel_extensions/tracedev.ko.post
      /install/syncfiles/phaseIII/nsd/multipath/multipath.conf.post
      #
      APPEND:
      /install/syncfiles/hosts/hosts.append -> /etc/hosts


      Best Regards,


      Qamar Nazir



      
------------------------------------------------------------------------------

      _______________________________________________
      xCAT-user mailing list
      xCAT-user@lists.sourceforge.net
      https://lists.sourceforge.net/lists/listinfo/xcat-user




------------------------------------------------------------------------------

_______________________________________________
xCAT-user mailing list
xCAT-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/xcat-user




------------------------------------------------------------------------------

_______________________________________________
xCAT-user mailing list
xCAT-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/xcat-user