Genesis version: # rpm -qa|grep genesis xCAT-genesis-base-x86_64-2.14.1.lenovo1-1.noarch xCAT-genesis-scripts-x86_64-2.14.1.lenovo2-1.noarch
find /opt/xcat/share/xcat/netboot/genesis/ -name rsync | xargs file search did not work ]# find / -name rsync /etc/selinux/targeted/active/modules/100/rsync /usr/bin/rsync /install/netboot/rhels7.5/x86_64/compute/rootimg/usr/bin/rsync /install/netboot/centos7.4/x86_64/compute/rootimg/usr/bin/rsync /install/sysclone/images/centos7.4-x86_64-install-compute-nvidia/etc/selinux/targeted/active/modules/100/rsync /install/sysclone/images/centos7.4-x86_64-install-compute-nvidia/usr/bin/rsync ]# lsinitrd /tftpboot/xcat/genesis.fs.x86_64.gz|grep rsync /tftpboot/xcat/genesis.fs.x86_64.gz does not exist Regards, Tom From: Bin XA Xu <bx...@cn.ibm.com> Sent: Thursday, September 27, 2018 11:11 PM To: xcat-user@lists.sourceforge.net Cc: xcat-user@lists.sourceforge.net Subject: [External] Re: [xcat-user] Sysclone image fails to install, goes to Genesis Shell instead Hi Thomas, Got below error message ``` rsync -a mgt::scripts/ /scripts/ /etc/init.d/functions: line 301: rsync: command not found ``` What's your genesis package version? would you like to run below commands rpm -qa|grep genesis find /opt/xcat/share/xcat/netboot/genesis/ -name rsync | xargs file lsinitrd /tftpboot/xcat/genesis.fs.x86_64.gz|grep rsync Bin Xu HPC Software Development Software Defined Infrastructure, IBM Systems Phone: 86-010-82454067 E-mail: bx...@cn.ibm.com<mailto:bx...@cn.ibm.com> ----- Original message ----- From: Thomas Alandt <tala...@lenovo.com<mailto:tala...@lenovo.com>> To: xCAT Users Mailing list <xcat-user@lists.sourceforge.net<mailto:xcat-user@lists.sourceforge.net>> Cc: Subject: [xcat-user] Sysclone image fails to install, goes to Genesis Shell instead Date: Fri, Sep 28, 2018 2:53 AM MN=xCAT Version 2.14.1.l, centos7.5 node originally installed with 7.5 diskfull install Followed instructions from: https://xcat-docs.readthedocs.io/en/stable/advanced/sysclone/sysclone.html All indications were that it was successfully cloned and the image was create/cloned onto the mn. But the node never installs the image and boots to the shell. After installing the original image that was created with copycds I can successfully install (diskfull). If I attempt to install cloned image, the node ends up in the genesis shell. If I boot to the hard drive, I boot into the previous image which tells me that it’s not getting to the point where its installing to the hard drive. Nodeset n1 <cloned image> rsetboot n1 boot rpower n1 reset [ 9.925415] sd 9:0:0:0: Attached scsi generic sg8 type 0 [ 9.940097] sd 9:0:0:0: [sdi] 4096-byte physical blocks [ 9.946152] sd 9:0:0:0: [sdi] Write Protect is off [ 9.951692] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.962556] sd 9:0:0:0: [sdi] Attached SCSI disk [ 10.329199] cdc_ether 1-1.6:1.0 usb0: kevent 12 may have been dropped [ 10.336618] cdc_ether 1-1.6:1.0 usb0: kevent 12 may have been dropped [ 12.968287] igb 0000:03:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX [ 12.978904] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready xcat.genesis.doxcat: Acquired IPv4 address on eth0 172.20.101.1/16 xcat.genesis.doxcat: Starting ntpd... xcat.genesis.doxcat: Attempting to sync hardware clock... xcat.genesis.doxcat: Restarting syslog... xcat.genesis.doxcat: Getting initial certificate --> mgt:3001 [ 14.534047] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.540753] 8021q: adding VLAN 0 to HW filter on device eth1 xcat.genesis.doxcat: Running getdestiny --> mgt:3001 xcat.genesis.doxcat: Received destiny=sysclone centos7.4-x86_64 xcat.genesis.doxcat: The destiny=sysclone, destiny parameters=sysclone centos7.4-x86_64 xcat.genesis.doxcat: Running dosysclone... ping_test Pinging your SystemImager server to ensure we have network connectivity. PING ATTEMPT 1: PING mgt.cluster (172.20.0.1) 56(84) bytes of data. 64 bytes from mgt.cluster (172.20.0.1): icmp_seq=1 ttl=64 time=0.125 ms --- mgt.cluster ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.125/0.125/0.125/0.000 ms We have connectivity to your SystemImager server! get_scripts_directory rsync -a mgt::scripts/ /scripts/ /etc/init.d/functions: line 301: rsync: command not found Last command exited with 127 Killing off running processes. writsh: no job control in this shell sh-4.2# e_variables cat: /etc/issue: No such file or directory [ 102.185906] random: crng init done sh-4.2# Thomas Alandt Global Engineering 8001 Development Drive, Morrisville, NC 27560 Lenovo USA [Phone]+1 (919) 237-8959 [Email]+1 (919) 696-8351 [VOIP]2978959 [Email]tala...@lenovo.com<mailto:zengd...@lenovo.com> Lenovo.com /www.lenovo.com <http://www.lenovo.com/www.lenovo.com> Twitter<http://twitter.com/lenovo> | Facebook | Instagram<https://instagram.com/lenovo> | Blogs<http://blog.lenovo.com/> | Forums<http://forums.lenovo.com/> [Lenovo_2015] _______________________________________________ xCAT-user mailing list xCAT-user@lists.sourceforge.net<mailto:xCAT-user@lists.sourceforge.net> https://lists.sourceforge.net/lists/listinfo/xcat-user
_______________________________________________ xCAT-user mailing list xCAT-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/xcat-user
