Before the MMU is turned on, PC uses physical address. Thus, one can use adr_l instead of load_paddr to obtain the physical address of a symbol.
The only exception (for this replacement) is create_table_entry() which is called before and after MMU is turned on. Also, in lookup_processor_type() "r10" is no longer used. The reason being __lookup_processor_type uses adr_l (thus r10 is no longer used to obtain the physical address offset). Signed-off-by: Ayan Kumar Halder <[email protected]> --- Refer https://lists.archive.carbon60.com/xen/devel/682900 for details. Changes from :- v1 :- 1. No need to modify create_table_entry(). 2. Remove "mov r10, #0 " in lookup_processor_type(). xen/arch/arm/arm32/head.S | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) diff --git a/xen/arch/arm/arm32/head.S b/xen/arch/arm/arm32/head.S index 33b038e7e0..e0ff46e92f 100644 --- a/xen/arch/arm/arm32/head.S +++ b/xen/arch/arm/arm32/head.S @@ -171,7 +171,7 @@ past_zImage: /* Using the DTB in the .dtb section? */ .ifnes CONFIG_DTB_FILE,"" - load_paddr r8, _sdtb + adr_l r8, _sdtb .endif /* Initialize the UART if earlyprintk has been enabled. */ @@ -213,7 +213,7 @@ GLOBAL(init_secondary) mrc CP32(r1, MPIDR) bic r7, r1, #(~MPIDR_HWID_MASK) /* Mask out flags to get CPU ID */ - load_paddr r0, smp_up_cpu + adr_l r0, smp_up_cpu dsb 2: ldr r1, [r0] cmp r1, r7 @@ -479,7 +479,7 @@ create_page_tables: * create_table_entry_paddr() will clobber the register storing * the physical address of the table to point to. */ - load_paddr r5, boot_third + adr_l r5, boot_third mov_w r4, XEN_VIRT_START .rept XEN_NR_ENTRIES(2) mov r0, r5 /* r0 := paddr(l3 table) */ @@ -578,7 +578,7 @@ enable_mmu: flush_xen_tlb_local r0 /* Write Xen's PT's paddr into the HTTBR */ - load_paddr r0, boot_pgtable + adr_l r0, boot_pgtable mov r1, #0 /* r0:r1 is paddr (boot_pagetable) */ mcrr CP64(r0, r1, HTTBR) isb @@ -877,7 +877,6 @@ putn: mov pc, lr /* This provides a C-API version of __lookup_processor_type */ ENTRY(lookup_processor_type) stmfd sp!, {r4, r10, lr} - mov r10, #0 /* r10 := offset between virt&phys */ bl __lookup_processor_type mov r0, r1 ldmfd sp!, {r4, r10, pc} @@ -897,8 +896,8 @@ ENTRY(lookup_processor_type) */ __lookup_processor_type: mrc CP32(r0, MIDR) /* r0 := our cpu id */ - load_paddr r1, __proc_info_start - load_paddr r2, __proc_info_end + adr_l r1, __proc_info_start + adr_l r2, __proc_info_end 1: ldr r3, [r1, #PROCINFO_cpu_mask] and r4, r0, r3 /* r4 := our cpu id with mask */ ldr r3, [r1, #PROCINFO_cpu_val] /* r3 := cpu val in current proc info */ -- 2.25.1
