Hi Philippe,
here is the next result (I have switched off the "quiet" kernel parameter to
get everything).
Regards
Mathias
++++++++++++++++++++++++++++++++++++++++++++++++++
Linux version 2.6.20.4 ([EMAIL PROTECTED]) (gcc version 4.1.2 20061115
(prerelease) (Debian 4.1.1-21)) #18 SMP Fri Apr 27 16:58:38 GMT-2 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009e000 end:
000000000009e000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009e000 size: 0000000000002000 end:
00000000000a0000 type: 2
copy_e820_map() start: 00000000000ca000 size: 0000000000002000 end:
00000000000cc000 type: 2
copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end:
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fde0000 end:
000000001fee0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001fee0000 size: 0000000000009000 end:
000000001fee9000 type: 3
copy_e820_map() start: 000000001fee9000 size: 0000000000017000 end:
000000001ff00000 type: 4
copy_e820_map() start: 000000001ff00000 size: 0000000000100000 end:
0000000020000000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end:
00000000fec10000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end:
00000000fee01000 type: 2
copy_e820_map() start: 00000000ff000000 size: 0000000001000000 end:
0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fee0000 (usable)
BIOS-e820: 000000001fee0000 - 000000001fee9000 (ACPI data)
BIOS-e820: 000000001fee9000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
510MB LOWMEM available.
found SMP MP-table at 000f5f40
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 130784
early_node_map[1] active PFN ranges
0: 0 -> 130784
DMI present.
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:6 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:6 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Detected 3192.197 MHz processor.
Built 1 zonelists. Total pages: 129763
Kernel command line: root=/dev/sda5 vga=ext isolcpus=1,3,7
console=ttyS0,115200n8
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
I-pipe 1.7-03: pipeline enabled.
Console: colour VGA+ 80x50
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 513860k/523136k available (2256k kernel code, 8696k reserved, 893k
data, 224k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffb7000 - 0xfffff000 ( 288 kB)
vmalloc : 0xe0800000 - 0xfffb5000 ( 503 MB)
lowmem : 0xc0000000 - 0xdfee0000 ( 510 MB)
.init : 0xc041a000 - 0xc0452000 ( 224 kB)
.data : 0xc03341f1 - 0xc041360c ( 893 kB)
.text : 0xc0100000 - 0xc03341f1 (2256 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6389.64 BogoMIPS (lpj=12779283)
Mount-cache hash table entries: 512
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 15k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 02
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6384.56 BogoMIPS (lpj=12769139)
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 02
Total of 2 processors activated (12774.21 BogoMIPS).
ENABLING IO-APIC IRQs
IRQ 1 vectored at #39
IRQ 3 vectored at #41
IRQ 4 vectored at #49
IRQ 5 vectored at #51
IRQ 6 vectored at #59
IRQ 7 vectored at #61
IRQ 8 vectored at #69
IRQ 9 vectored at #71
IRQ 10 vectored at #79
IRQ 11 vectored at #81
IRQ 12 vectored at #89
IRQ 13 vectored at #91
IRQ 14 vectored at #99
IRQ 15 vectored at #a1
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 2.10 entry at 0xfd877, last bus=10
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
0000:00:1f.1: trying to change BAR0 from 0000 to 01F0
0000:00:1f.1: trying to change BAR1 from 0000 to 03F4
0000:00:1f.1: trying to change BAR2 from 0000 to 0170
0000:00:1f.1: trying to change BAR3 from 0000 to 0374
PCI: PXH quirk detected, disabling MSI for SHPC device
PCI: Firmware left 0000:0a:06.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 11 14 15) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 10 11 14 15) *12
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: e0100000-e1ffffff
PREFETCH window: e8000000-efffffff
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0100000-e1ffffff
PREFETCH window: e8000000-efffffff
PCI: Bridge: 0000:03:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: e2000000-e20fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: 4000-4fff
MEM window: e2100000-e21fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: 5000-5fff
MEM window: e2200000-e22fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: 6000-6fff
MEM window: e2300000-e3ffffff
PREFETCH window: 30000000-300fffff
IRQ 16 vectored at #a9
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
IRQ 17 vectored at #b1
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 348k freed
Simple Boot Flag at 0x37 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1177686146.976:1): initialized
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
assign_interrupt_mode Found MSI capability
IRQ 223 vectored at #b9
assign_interrupt_mode Found MSI capability
IRQ 222 vectored at #c1
assign_interrupt_mode Found MSI capability
IRQ 221 vectored at #c9
assign_interrupt_mode Found MSI capability
IRQ 220 vectored at #d1
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
IRQ 18 vectored at #d9
ACPI: PCI Interrupt 0000:05:00.3[C] -> GSI 18 (level, low) -> IRQ 18
0000:05:00.3: ttyS2 at I/O 0x4020 (irq = 18) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3020-0x3027, BIOS settings: hda:DMA, hdb:pio
hda: HL-DT-STDVD-ROM GDR8164B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
IRQ 19 vectored at #e1
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ata1: SATA max UDMA/133 cmd 0x3068 ctl 0x305E bmdma 0x3030 irq 19
ata2: SATA max UDMA/133 cmd 0x3060 ctl 0x305A bmdma 0x3038 irq 19
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/133, 160836480 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0x3067
scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72168 P21O PQ: 0 ANSI: 5
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
input: PC Speaker as /class/input/input3
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
RAMDISK: Compressed image found at block 0
Time: tsc clocksource has been installed.
VFS: Mounted root (minix filesystem).
Requested Root Partition: sda5. OK
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... /initrd does not exist. Ignored.
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 224k freed
INIT: version 2.86 booting
Setting parameters of disc: (none).
Setting the system clock..
Mounting proc filesystem
mount: proc already mounted
Cleaning up ifupdown....
Loading kernel modules...done.
Loading device-mapper support.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)
done.
Setting kernel variables...done.
Checking /etc/fstab.
Mounting local filesystems...ReiserFS: sda1: found reiserfs format "3.6" with
standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
done.
Activating swapfile swap...done.
Configuring network interfaces...Intel(R) PRO/1000 Network Driver - version
7.3.15-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16
e1000: 0000:05:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1)
00:30:48:5a:f9:0a
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
IRQ 219 vectored at #e9
BUG: unable to handle kernel paging request at virtual address 511203b2
printing eip:
c03e5680
*pde = 00000000
Oops: 0002 [#1]
SMP
Modules linked in: e1000
CPU: 0
EIP: 0060:[<c03e5680>] Not tainted VLI
EFLAGS: 00010092 (2.6.20.4 #18)
EIP is at 0xc03e5680
eax: c011226c ebx: 00000006 ecx: c0114375 edx: dfc1a000
esi: 00000046 edi: ffffffff ebp: 00000000 esp: dfc1be24
ds: 007b es: 007b ss: 0068
Process ifconfig (pid: 1241, ti=dfc1a000 task=dfcb3030 task.ti=dfc1a000)
Stack: 000000db 00000000 c03d9100 c010efa9 00006d80 00000001 00000060 e099a210
00000286 ffffff24 df7015c8 00000000 0000000f 00000001 c0103439 df7015c8
e099a0ff e09c0000 00000000 0000000f 00000001 80080740 c14a007b df70007b
Call Trace:
[<c010efa9>] __ipipe_handle_irq+0x1b9/0x20b
[<e099a210>] e1000_set_multi+0x111/0x189 [e1000]
[<c0103439>] common_interrupt+0x21/0x38
[<e099a0ff>] e1000_set_multi+0x0/0x189 [e1000]
[<e099a210>] e1000_set_multi+0x111/0x189 [e1000]
[<c02dcfb1>] __dev_mc_upload+0x1d/0x1e
[<c02dd0d1>] dev_mc_upload+0x24/0x37
[<c02db5dc>] dev_open+0x44/0x62
[<c02da0a9>] dev_change_flags+0x47/0xe4
[<c030d1c2>] devinet_ioctl+0x252/0x56f
[<c02db1ba>] dev_ifsioc+0x113/0x38d
[<c02d15d4>] sock_ioctl+0x0/0x1ad
[<c02d1762>] sock_ioctl+0x18e/0x1ad
[<c02d15d4>] sock_ioctl+0x0/0x1ad
[<c015e1bf>] do_ioctl+0x1f/0x62
[<c015e446>] vfs_ioctl+0x244/0x256
[<c015e48b>] sys_ioctl+0x33/0x4c
[<c01029f3>] sysenter_past_esp+0x6c/0x70
=======================
Code: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <00> 91 3d c0 00 91 3d
c0 00 00 00 00 00 00 00 00 00 00 00 00 00
EIP: [<c03e5680>] 0xc03e5680 SS:ESP 0068:dfc1be24
<0>Kernel panic - not syncing: Fatal exception in interrupt
BUG: at arch/i386/kernel/smp.c:565 smp_call_function()
[<c010b903>] smp_call_function+0x66/0x10a
[<c0118e3a>] printk+0x62/0xd5
[<c010b9c2>] smp_send_stop+0x1b/0x2b
[<c01183d5>] panic+0x4d/0xe4
[<c0103f71>] die+0x1f2/0x226
[<c01116a4>] do_page_fault+0x447/0x517
[<c013fbae>] __alloc_pages+0x52/0x286
[<c010f643>] __ipipe_handle_exception+0xce/0x158
[<c01521e3>] kmem_cache_alloc+0x5d/0x67
[<c010bb1e>] smp_call_function_interrupt+0x31/0x4c
[<c033339d>] error_code+0x81/0x90
[<c0114375>] try_to_wake_up+0x33c/0x346
[<c011226c>] __activate_task+0x1c/0x29
[<c010efa9>] __ipipe_handle_irq+0x1b9/0x20b
[<e099a210>] e1000_set_multi+0x111/0x189 [e1000]
[<c0103439>] common_interrupt+0x21/0x38
[<e099a0ff>] e1000_set_multi+0x0/0x189 [e1000]
[<e099a210>] e1000_set_multi+0x111/0x189 [e1000]
[<c02dcfb1>] __dev_mc_upload+0x1d/0x1e
[<c02dd0d1>] dev_mc_upload+0x24/0x37
[<c02db5dc>] dev_open+0x44/0x62
[<c02da0a9>] dev_change_flags+0x47/0xe4
[<c030d1c2>] devinet_ioctl+0x252/0x56f
[<c02db1ba>] dev_ifsioc+0x113/0x38d
[<c02d15d4>] sock_ioctl+0x0/0x1ad
[<c02d1762>] sock_ioctl+0x18e/0x1ad
[<c02d15d4>] sock_ioctl+0x0/0x1ad
[<c015e1bf>] do_ioctl+0x1f/0x62
[<c015e446>] vfs_ioctl+0x244/0x256
[<c015e48b>] sys_ioctl+0x33/0x4c
[<c01029f3>] sysenter_past_esp+0x6c/0x70
=======================
----- Original Nachricht ----
Von: Philippe Gerum <[EMAIL PROTECTED]>
An: "M. Koehrer" <[EMAIL PROTECTED]>
Datum: 27.04.2007 17:05
Betreff: Re: Re: [Xenomai-help] Xenomai and MSI enabled crashes kernel
> On Fri, 2007-04-27 at 16:56 +0200, Philippe Gerum wrote:
> > On Fri, 2007-04-27 at 16:28 +0200, M. Koehrer wrote:
> > > Hello Philippe,
> > >
> > > here it is: (I have no idea what BUGON does...)
> > >
> >
> > This patch will print out the irq/vector mappings. I'm interested in
> > reading this output.
> >
> > --- arch/i386/kernel/io_apic.c~ 2007-02-26 10:31:39.000000000 +0100
> > +++ arch/i386/kernel/io_apic.c 2007-04-27 16:51:51.000000000 +0200
> > @@ -1259,6 +1259,7 @@
> > current_vector = vector;
> > current_offset = offset;
> > irq_vector[irq] = vector;
> > + printk("IRQ %d vectored at #%2x\n", irq, vector);
>
> Please s/%2x/%.2x
>
> >
> > return vector;
> > }
> >
> --
> Philippe.
>
>
>
--
Mathias Koehrer
[EMAIL PROTECTED]
50 AMAZON-Einkaufsgutschein bei Bestellung von Arcor-DSL:
Viel oder wenig? Schnell oder langsam? Unbegrenzt surfen + telefonieren
ohne Zeit- und Volumenbegrenzung? DAS TOP ANGEBOT JETZT bei Arcor: günstig
und schnell mit DSL - das All-Inclusive-Paket für clevere Doppel-Sparer,
nur 39,85 inkl. DSL- und ISDN-Grundgebühr!
http://www.arcor.de/rd/emf-dsl-2
_______________________________________________
Xenomai-help mailing list
[email protected]
https://mail.gna.org/listinfo/xenomai-help
