Bob Feretich wrote:
> Thank you for the quick reply.
>
> I rebuilt the non-Adeos patched kernel with the 32 KHz clocked disabled.
> It booted correctly, so that wasn't the problem. I didn't see any other
> significant differences in the console boot logs.
>
> The console log for the non-Adeos patched kernel with the 32 KHz clocked
> disabled is pasted below. The /proc/interrupts contents is displayed at
> the end.
>
> I used the 1.16-01 patch.
>
>> Reading boot sector
>> Loading u-boot.bin from mmc
>>
>>
>> U-Boot 2009.06-rc2 (Nov 02 2009 - 23:57:20)
>>
>> OMAP3530-GP ES3.0, CPU-OPP2 L3-165MHz
>> OMAP3 Beagle board + LPDDR/NAND
>> DRAM: 256 MB
>> NAND: 256 MiB
>> In: serial
>> Out: serial
>> Err: serial
>> Board revision C
>> Die ID #317000030000000004013f8a1701a01b
>> Hit any key to stop autoboot: 0
>> mmc1 is available
>> reading uImage
>>
>> 1867604 bytes read
>> ## Booting kernel from Legacy Image at 80300000 ...
>> Image Name: Angstrom/2.6.31/beagleboard
>> Image Type: ARM Linux Kernel Image (uncompressed)
>> Data Size: 1867540 Bytes = 1.8 MB
>> Load Address: 80008000
>> Entry Point: 80008000
>> Verifying Checksum ... OK
>> Loading Kernel Image ... OK
>> OK
>>
>> Starting kernel ...
>>
>> Uncompressing
>> Linux.........................................................................................
>> ............................. done, booting the kernel.
>> Linux version 2.6.31-omap1 ([email protected]) (gcc version 4.3.3 (GCC)
>> ) #2 Sun Jul 18 22:38:24 PDT 2010
>> CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
>> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
>> Machine: OMAP3 Beagle Board
>> Memory policy: ECC disabled, Data cache writeback
>> OMAP3430 ES3.0
>> SRAM: Mapped pa 0x40200000 to va 0xe3000000 size: 0x100000
>> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
>> Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw
>> rootfstype=ext3 rootwait
>> PID hash table entries: 1024 (order: 10, 4096 bytes)
>> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
>> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
>> Memory: 128MB 128MB = 256MB total
>> Memory: 255872KB available (3232K code, 290K data, 132K init, 0K highmem)
>> NR_IRQS:402
>> Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
>> Reprogramming SDRC clock to 332000000 Hz
>> GPMC revision 5.0
>> IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
>> Total of 96 interrupts on 1 active controller
>> OMAP34xx GPIO hardware version 2.5
>> OMAP clockevent source: GPTIMER1 at 13000000 Hz
>> Console: colour dummy device 80x30
>> Calibrating delay loop... 498.07 BogoMIPS (lpj=2490368)
>> Mount-cache hash table entries: 512
>> CPU: Testing write buffer coherency: ok
>> regulator: core version 0.5
>> NET: Registered protocol family 16
>> Found NAND on CS0
>> Registering NAND on CS0
>> OMAP DMA hardware revision 4.0
>> bio: create slab <bio-0> at 0
>> i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
>> twl4030: PIH (irq 7) chaining IRQs 368..375
>> twl4030: power (irq 373) chaining IRQs 376..383
>> twl4030: gpio (irq 368) chaining IRQs 384..401
>> regulator: VMMC1: 1850 <--> 3150 mV normal standby
>> regulator: VDAC: 1800 mV normal standby
>> regulator: VUSB1V5: 1500 mV normal standby
>> regulator: VUSB1V8: 1800 mV normal standby
>> regulator: VUSB3V1: 3100 mV normal standby
>> regulator: VPLL2: 1800 mV normal standby
>> regulator: VSIM: 1800 <--> 3000 mV normal standby
>> i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
>> SCSI subsystem initialized
>> twl4030_usb twl4030_usb: Initialized TWL4030 USB module
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
>> musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92
>> NET: Registered protocol family 2
>> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
>> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
>> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
>> TCP: Hash tables configured (established 8192 bind 8192)
>> TCP reno registered
>> NET: Registered protocol family 1
>> VFS: Disk quotas dquot_6.5.2
>> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>> JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
>> msgmni has been set to 500
>> alg: No test for stdrng (krng)
>> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
>> io scheduler noop registered
>> io scheduler anticipatory registered (default)
>> io scheduler deadline registered
>> io scheduler cfq registered
>> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
>> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
>> serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
>> serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
>> console [ttyS2] enabled
>> brd: module loaded
>> loop: module loaded
>> i2c /dev entries driver
>> usbcore: registered new interface driver asix
>> usbcore: registered new interface driver cdc_ether
>> usbcore: registered new interface driver net1080
>> usbcore: registered new interface driver cdc_subset
>> usbcore: registered new interface driver zaurus
>> usbmon: debugfs is not available
>> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
>> ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
>> ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
>> ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
>> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
>> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb1: Product: OMAP-EHCI Host Controller
>> usb usb1: Manufacturer: Linux 2.6.31-omap1 ehci_hcd
>> usb usb1: SerialNumber: ehci-omap.0
>> usb usb1: configuration #1 chosen from 1 choice
>> hub 1-0:1.0: USB hub found
>> hub 1-0:1.0: 3 ports detected
>> g_ether gadget: using random self ethernet address
>> g_ether gadget: using random host ethernet address
>> usb0: MAC 8a:fe:ec:d2:7c:3d
>> usb0: HOST MAC 9a:ca:2d:10:da:55
>> g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
>> g_ether gadget: g_ether ready
>> musb_hdrc musb_hdrc: MUSB HDRC host driver
>> musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
>> usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
>> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb2: Product: MUSB HDRC host driver
>> usb usb2: Manufacturer: Linux 2.6.31-omap1 musb-hcd
>> usb usb2: SerialNumber: musb_hdrc
>> usb usb2: configuration #1 chosen from 1 choice
>> hub 2-0:1.0: USB hub found
>> hub 2-0:1.0: 1 port detected
>> mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
>> TCP cubic registered
>> NET: Registered protocol family 17
>> NET: Registered protocol family 15
>> RPC: Registered udp transport module.
>> RPC: Registered tcp transport module.
>> Power Management for TI OMAP3.
>> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
>> regulator_init_complete: incomplete constraints, leaving VDVI on
>> regulator_init_complete: incomplete constraints, leaving VDAC on
>> Waiting for root device /dev/mmcblk0p2...
>> mmc0: new high speed SDHC card at address 1234
>> mmcblk0: mmc0:1234 SA04G 3.68 GiB
>> mmcblk0: p1 p2
>> kjournald starting. Commit interval 5 seconds
>> EXT3 FS on mmcblk0p2, internal journal
>> EXT3-fs: mounted filesystem with writeback data mode.
>> VFS: Mounted root (ext3 filesystem) on device 179:2.
>> Freeing init memory: 132K
>> INIT: version 2.86 booting
>> Please wait: booting...
>> Starting udev
>> Remounting root file system...
>> Caching udev devnodes
>> Populating dev cache
>> root: mount: mounting rootfs on / failed: No such file or directory
>> Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
>> done.
>> Setting up IP spoofing protection: rp_filter.
>> hwclock: can't open '/dev/misc/rtc': No such file or directory
>> Tue May 18 20:58:00 UTC 2010
>> hwclock: can't open '/dev/misc/rtc': No such file or directory
>> Configuring update-modules.
>> Starting to configure packages...
>> Nothing to be done
>> Finished to configure packages.
>> INIT: Entering runlevel: 5
>> Creating Dropbear SSH server RSA host key.
>> Will output 1024 bit rsa secret key to
>> '/etc/dropbear/dropbear_rsa_host_key'
>> Generating key, this may take a while...
>> Public key portion is:
>> ssh-rsa
>> AAAAB3NzaC1yc2EAAAADAQABAAAAgwDJb1gWi2/u83v7e+S9Ij31aK/QMD72J47fdtDm4jn37GTq6JpL7UxsmcTGRB30bmKFzMhP
>> w0uCsbTAeU29KOG6BdlSYK1oI5bDl7jdYHeBvhoejrDCvdp3R9//3rVs0y+c7WYgDRid5aOxSSUAg2j+Ec6PuGniLBNYWOG7mJmru79P
>>
>> roo
>> t...@beagleboard
>> Fingerprint: md5 c6:e9:c0:07:33:e3:5c:61:35:a5:e0:24:e0:41:03:86
>> Starting Dropbear SSH server: dropbear.
>> Starting syslogd/klogd: done
>>
>> .-------.
>> | | .-.
>> | | |-----.-----.-----.| | .----..-----.-----.
>> | | | __ | ---'| '--.| .-'| | |
>> | | | | | |--- || --'| | | ' | | | |
>> '---'---'--'--'--. |-----''----''--' '-----'-'-'-'
>> -' |
>> '---'
>>
>> The Angstrom Distribution beagleboard ttyS2
>>
>> Angstrom 2010.4-test-20100518 beagleboard ttyS2
>>
>> beagleboard login: root
>> r...@beagleboard:~# cat /proc/interrupts
>> CPU0
>> 7: 2 INTC TWL4030-PIH
>> 11: 0 INTC prcm
>> 12: 1078 INTC DMA
>> 37: 1009 INTC gp timer
>> 56: 273 INTC i2c_omap
>> 61: 0 INTC i2c_omap
>> 72: 1 INTC serial idle
>> 73: 1 INTC serial idle
>> 74: 158 INTC serial idle, serial
>> 77: 0 INTC ehci_hcd:usb1
>> 83: 1346 INTC mmc0
>> 92: 1 INTC musb_hdrc
>> 93: 0 INTC musb_hdrc
>> 378: 2 twl4030 twl4030_usb
>> 384: 0 twl4030 mmc0
>> Err: 0
>> r...@beagleboard:~#
Ok. Several questions: what is this MADC patch you were talking about?
If this is a kernel patch, if yes, could you try and remove it?
You have an error message about mmc:
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
which I do not have. Could this not explain some issues?
You are using the 2.6.31 kernel which does not work for you, whereas
2.6.33 works for me. Could you test 2.6.33?
--
Gilles.
_______________________________________________
Xenomai-help mailing list
[email protected]
https://mail.gna.org/listinfo/xenomai-help
