I had time to test this on a Zynq microzed board using the new 4.14 ipipe and it works without issue. What branch are you using from the Xenomai repo?
On Mon, Mar 12, 2018 at 12:56 PM, Шевченко Тарас Григорьевич <shevchenko.ta...@triolcorp.com.ua> wrote: > sad, to hear it > it is possible to remind you if I get fail with gpio? > > Yes I able to build from repo , I wrote about , today earlier > > I used some different way - like in your instruction > > make bzImage modules > make install > > > ----- Original Message ----- > From: "Greg Gallagher" <g...@embeddedgreg.com> > To: "Шевченко Тарас Григорьевич" <shevchenko.ta...@triolcorp.com.ua> > Cc: "xenomai" <xenomai@xenomai.org> > Sent: Monday, March 12, 2018 6:50:47 PM > Subject: Re: [Xenomai] simple rtdm driver x86 > > No that shouldn't have an impact on it. I have a couple theories > about what is happening but I don't have time to test them out at the > moment. Hopefully I'll have some time closer to the end of the week > to look into it. Where you able to build from the git repo? > > -Greg > > On Mon, Mar 12, 2018 at 12:45 PM, Шевченко Тарас Григорьевич > <shevchenko.ta...@triolcorp.com.ua> wrote: >> >> could be the problem in loading out-of-tree module taints kernel. >> >> yeti@yeti-UDOO-x86:~/develop/rtdm_hello$ dmesg|grep rtdm >> [ 1536.073433] rtdm_hello: loading out-of-tree module taints kernel. >> [ 1536.073532] rtdm_hello: module verification failed: signature and/or >> required key missing - tainting kernel >> yeti@yeti-UDOO-x86:~/develop/rtdm_hello$ dmesg|grep RTDM >> [ 1536.075500] RTDM gpio init. >> [ 1536.075617] RTDM numero 266: >> >> >> >> ----- Original Message ----- >> From: "Greg Gallagher" <g...@embeddedgreg.com> >> To: "Шевченко Тарас Григорьевич" <shevchenko.ta...@triolcorp.com.ua> >> Cc: "xenomai" <xenomai@xenomai.org> >> Sent: Monday, March 12, 2018 5:46:05 PM >> Subject: Re: [Xenomai] simple rtdm driver x86 >> >> Use this https://xenomai.org/documentation/xenomai-3/html/xeno3prm/index.html >> for rtdm references going forward. You are running Xenomai 3, but >> using the docs for 2.6. >> >> -Greg >> >> On Mon, Mar 12, 2018 at 11:41 AM, Шевченко Тарас Григорьевич >> <shevchenko.ta...@triolcorp.com.ua> wrote: >>> Xenomai 3 >>> It is work! Perfect! >>> Now i have the same problem as below >>> http://xenomai.org/pipermail/xenomai/2017-May/037361.html by Nitin Kulkarni >>> and x86 >>> >>> interrupt registered cat /proc/xenomai/irq >>> >>> >>> IRQ CPU0 CPU1 CPU2 CPU3 >>> 266: 0 0 0 0 rtdm_hello >>> >>> but the handler is not invoked when I trigger the gpio pin. >>> I found >>> http://xenomai.org/documentation/xenomai-2.6/html/api/group__rtdmirq.html#gaf4e76db13d7f7aac4be2cae59e0097bc >>> only RTDM_IRQTYPE_EDGE option >>> is there another trigger or another way to do it ? >>> >>> >>> ----- Original Message ----- >>> From: "Greg Gallagher" <g...@embeddedgreg.com> >>> To: "Шевченко Тарас Григорьевич" <shevchenko.ta...@triolcorp.com.ua> >>> Cc: "xenomai" <xenomai@xenomai.org> >>> Sent: Monday, March 12, 2018 4:16:03 PM >>> Subject: Re: [Xenomai] simple rtdm driver x86 >>> >>> Are you using Xenomai 3 or 2? I believe from your previous posts you >>> are using Xenomai 3, include rtdm/driver.h , not rtdm_driver.h. >>> >>> -Greg >>> >>> On Mon, Mar 12, 2018 at 10:09 AM, Шевченко Тарас Григорьевич >>> <shevchenko.ta...@triolcorp.com.ua> wrote: >>>> Hi, >>>> could somebody share simple rtdm driver for begginers >>>> better fo x86 >>>> I try to find it but almost for arm >>>> and i have no such rtdm_driver.h >>>> give an advice please should I start from ? >>>> _______________________________________________ >>>> Xenomai mailing list >>>> Xenomai@xenomai.org >>>> https://xenomai.org/mailman/listinfo/xenomai _______________________________________________ Xenomai mailing list Xenomai@xenomai.org https://xenomai.org/mailman/listinfo/xenomai
