> I just installed a new Motherboard with integrated video. Redhat 9 is trying to use the Trident > > driver, but no go. Can you help?
using http://yourvote.com/pci again (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 1106,3112 card 1106,3112 rev 00 class 06,00,00 hdr 00 VIA VT8361 CPU bridge - Apollo KLE133 (II) PCI: 01:00:0: chip 1023,8500 card 1023,8500 rev 00 class 03,00,00 hdr 00 Trident CyberBlade i1 AGP (II) LoadModule: "trident" (II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o (II) Module trident: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 Module class: XFree86 Video Driver ABI class: XFree86 Video Driver, version 0.6 nice (II) TRIDENT: driver for Trident chipsets: tvga9000, tvga9000i, tvga8900c, tvga8900d, tvga9200cxr, tgui9400cxi, cyber9320, cyber9388, cyber9397, cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4, tgui9420dgi, tgui9440agi, tgui9660, tgui9680, providia9682, providia9685, cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d, cyberbladei7, cyberbladei7d, cyberbladei1, cyberbladei1d, cyberbladeAi1, cyberbladeAi1d, bladeXP, cyberbladeXPAi1 (II) Primary Device is: PCI 01:00:0 (--) Assigning device section with no busID to primary device (--) Chipset cyberbladei1 found nice as well. (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11R6/lib/modules/libddc.a (II) Module ddc: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.6 (II) TRIDENT(0): VESA VBE DDC supported (II) TRIDENT(0): VESA VBE DDC Level 1 + 2 (II) TRIDENT(0): VESA VBE DDC transfer in appr. 1 sec. (II) TRIDENT(0): VESA VBE DDC read successfully (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Reloading /usr/X11R6/lib/modules/libddc.a (II) TRIDENT(0): Manufacturer: DEL Model: 4273 Serial#: 811161910 (II) TRIDENT(0): Year: 1997 Week: 18 (II) TRIDENT(0): EDID Version: 1.0 (II) TRIDENT(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V (II) TRIDENT(0): Sync: Separate (II) TRIDENT(0): Max H-Image Size [cm]: horiz.: 28 vert.: 20 (II) TRIDENT(0): Gamma: 1.01 (II) TRIDENT(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display (II) TRIDENT(0): redX: 0.004 redY: 0.004 greenX: 0.004 greenY: 0.005 (II) TRIDENT(0): blueX: 0.004 blueY: 0.004 whiteX: 0.004 whiteY: 0.005 (II) TRIDENT(0): Supported VESA Video Modes: (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): [EMAIL PROTECTED] (II) TRIDENT(0): Manufacturer's mask: 0 (II) TRIDENT(0): Supported additional Video Mode: (II) TRIDENT(0): clock: 110.0 MHz Image Size: 262 x 196 mm (II) TRIDENT(0): h_active: 1280 h_sync: 1358 h_sync_end 1470 h_blank_end 1720 h_border: 0 (II) TRIDENT(0): v_active: 1024 v_sync: 1025 v_sync_end 1030 v_blanking: 1067 v_border: 0 (--) TRIDENT(0): Revision is 106 (--) TRIDENT(0): Found CyberBlade/i1 chip (--) TRIDENT(0): RAM type is SDRAM (--) TRIDENT(0): Using SW cursor (--) TRIDENT(0): VideoRAM: 8192 kByte (--) TRIDENT(0): STN Panel 1280x1024 found (--) TRIDENT(0): Memory Clock is 57.27 MHz (==) TRIDENT(0): Min pixel clock is 12 MHz (--) TRIDENT(0): Max pixel clock is 230 MHz (II) TRIDENT(0): Monitor0: Using hsync range of 57.00-64.00 kHz (II) TRIDENT(0): Monitor0: Using vrefresh range of 55.00-90.00 Hz (II) TRIDENT(0): Clock range: 12.00 to 230.00 MHz seems there is a flat panel. (II) TRIDENT(0): Not using default mode "640x350" (hsync out of range) (II) TRIDENT(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) [...] (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (EE) TRIDENT(0): Virtual height (0) is too small for the hardware (min 128) seems the predefined modelines dont server you screen device. you must create modelines of your own that serve the needs. (EE) Screen(s) found, but none have a usable configuration. Fatal server error: no screens found no wonder why your display does not come up. care for the matching modelines, anything else is okay. -Alex. _______________________________________________ XFree86 mailing list [EMAIL PROTECTED] http://XFree86.Org/mailman/listinfo/xfree86
