You are using "Monitor0" with rather limited flexibility:
HorizSync 60.0 - 60.0
then to be sure you add
HorizSync 56-75
if I were X I might get confused...
cheers
Lionel
PS clear all the junk from your XF86Config that way possible messes are easier to
detect
--- Danny Anderson <[EMAIL PROTECTED]> wrote:
> Hola!
>
> I have an NEC Multisync LCD1765. I have not been able to get this monitor
> to work with RH9. I tried Mandrake 9.0 and the monitor worked without
> problems. I tried Mandy for awhile, but I really want to go back to Redhat
> if possible.
>
> I have tried to merge the working XF86Config files from M9 into the RH9
> version without success.
>
> My attention is currently focused on the horizontal and vertical sync rates.
> If I enable the Redhat settings at 60Hz and 60Hz, there are no errors, but
> the monitor reports "No signal found- going to sleep". I am currently
> booting to a prompt, so I can use CTRL-ALT-BKSPC to log out back to the
> prompt. When I return to the prompt, the screen is full of the typical
> messages one gets when logging out of an x server to a prompt. If I enable
> the Mandrake settings (by commenting out the appropriate set of values), I
> get the following errors:
>
> (EE) VESA(0): No matching modes
> (EE) Screen(s) found, no none have a usable configuration
>
> Fatal server error:
> no screens found.
>
> My Frankenstien XF86Config file is enclosed. I know somebody out there has
> the answer or a really good hunch. All commnets and suggestions
> appreciated. Lenard, your suggestions will be wasted on me, since I am
> using a Microsoft newreader until I can get Redhat working or go back to
> Mandrake.
>
> Thanks, all!
> Danny
>
> //---start XF86Config
>
> # XFree86 4 configuration created by pyxf86config
> # ----------------------------------------------------- #
> # modified heavily by bturnip in attempt to get X #
> # working with NEC Mulitsync LCD 1765. This monitor #
> # worked fine with Mankdrake 9.1 setup, so my strategy #
> # is a merger of the Redhat and Mandrake setups #
> # ----------------------------------------------------- #
>
> Section "ServerLayout"
> Identifier "Default Layout"
> Screen 0 "Screen0" 0 0
> InputDevice "Mouse0" "CorePointer"
> InputDevice "Keyboard0" "CoreKeyboard"
> InputDevice "DevInputMice" "AlwaysCore"
> EndSection
>
> Section "Files"
> # RgbPath is the location of the RGB database. Note, this is the name of
> the
> # file minus the extension (like ".txt" or ".db"). There is normally
> # no need to change the default.
>
> # Multiple FontPath entries are allowed (they are concatenated together)
> # By default, Red Hat 6.0 and later now use a font server independent of
> # the X server to render fonts.
>
> RgbPath "/usr/X11R6/lib/X11/rgb"
> FontPath "unix/:7100"
> EndSection
>
> Section "Module"
> Load "dbe"
> Load "extmod"
> Load "fbdevhw"
> Load "glx"
> Load "record"
> Load "freetype"
> Load "type1"
> Load "dri"
> EndSection
>
> Section "InputDevice"
> # ----------------------------------------------------- #
> # Lots of comments deleted here- see XF86ConfigOriginal #
> # for instructions about various keyboard options. #
> # ----------------------------------------------------- #
> Identifier "Keyboard0"
> Driver "keyboard"
> Option "XkbRules" "xfree86"
> Option "XkbModel" "pc105"
> Option "XkbLayout" "us"
> EndSection
>
> Section "InputDevice"
> Identifier "Mouse0"
> Driver "mouse"
> Option "Protocol" "IMPS/2"
> Option "Device" "/dev/psaux"
> Option "ZAxisMapping" "4 5"
> Option "Emulate3Buttons" "no"
> EndSection
>
> Section "InputDevice"
> # If the normal CorePointer mouse is not a USB mouse then
> # this input device can be used in AlwaysCore mode to let you
> # also use USB mice at the same time.
> Identifier "DevInputMice"
> Driver "mouse"
> Option "Protocol" "IMPS/2"
> Option "Device" "/dev/input/mice"
> Option "ZAxisMapping" "4 5"
> Option "Emulate3Buttons" "no"
> EndSection
>
> # ----------------------------------------------------- #
> # - - - - - -lots of editing starting here- - - - - - - #
> # the [Monitor] section immediately following contains #
> # the original redhat values. Currently (9/6 4:00pm) #
> # I haven't been able to tell if any difference is seen #
> # if "DisplaySize" or "Option" are commented out or not #
> # For values commented out in this first section, the #
> # matching value should be enabled in the second #
> # [Monitor] section, which contains values that worked #
> # under Mandrake 9.0 #
> # ----------------------------------------------------- #
>
> Section "Monitor"
> Identifier "Monitor0"
> VendorName "Monitor Vendor"
> ModelName "DDCPROBED"
> # DisplaySize 340 270
> HorizSync 60.0 - 60.0
> # VertRefresh 60.0 - 60.0
> # Option "dpms"
> #EndSection
> # ---End-of-Redhat-Section----------------------------- #
> #
> #
> # ----------------------------------------------------- #
> # Mandrake 9.1 XF86Config settings #
> # ----------------------------------------------------- #
> #Section "Monitor"
> # Identifier "monitor1"
> # VendorName "Plug'n Play"
> # !!! Trying to find a good adjustment for these values
> # !!! With these valuse enabled, the X server seems to
> # !!! start without errors, but the monitor reports "No signal"
> # !!! and goes to sleep.
> # !!! ORIG MANDRAKE VALUES:
> # HorizSync 31-81
> # VertRefresh 56-75
> HorizSync 56-75
> VertRefresh 56-75
>
> # Sony Vaio C1(X,XS,VE,VN)?
> # 1024x480 @ 85.6 Hz, 48 kHz hsync
> ModeLine "1024x480" 65.00 1024 1032 1176 1344 480 488 494
> 563 -hsync -vsync
>
> # TV fullscreen mode or DVD fullscreen output.
> # 768x576 @ 79 Hz, 50 kHz hsync
> ModeLine "768x576" 50.00 768 832 846 1000 576 590 595 630
>
> # 768x576 @ 100 Hz, 61.6 kHz hsync
> ModeLine "768x576" 63.07 768 800 960 1024 576 578 590 616
>
> # This is a set of standard mode timings. Modes that are out of monitor
> # spec are automatically deleted by the server (provided the HorizSync
> # and VertRefresh lines are correct), so there's no immediate need to
> # delete mode timings (unless particular mode timings don't work on your
> # monitor). With these modes, the best standard mode that your monitor
> # and video card can support for a given resolution is automatically
> # used.
>
> # 640x480 @ 60 Hz, 31.5 kHz hsync
> ModeLine "640x480" 25.175 640 664 760 800 480 491 493 525
>
> # 800x600 @ 56 Hz, 35.15 kHz hsync
> ModeLine "800x600" 36 800 824 896 1024 600 601 603 625
>
> # 1024x768 @ 87 Hz interlaced, 35.5 kHz hsync
> ModeLine "1024x768" 44.9 1024 1048 1208 1264 768 776 784 817
> Interlace
>
> # 640x400 @ 85 Hz, 37.86 kHz hsync
> ModeLine "640x400" 31.5 640 672 736 832 400 401 404
> 445 -HSync +VSync
>
> # 640x480 @ 75 Hz, 37.50 kHz hsync
> ModeLine "640x480" 31.5 640 656 720 840 480 481 484
> 500 -HSync -VSync
>
> # 800x600 @ 60 Hz, 37.8 kHz hsync
> ModeLine "800x600" 40 800 840 968 1056 600 601 605 628
> +hsync +vsync
>
> # 640x480 @ 85 Hz, 43.27 kHz hsync
> ModeLine "640x480" 36 640 696 752 832 480 481 484
> 509 -HSync -VSync
>
> # 1152x864 @ 89 Hz interlaced, 44 kHz hsync
> ModeLine "1152x864" 65 1152 1168 1384 1480 864 865 875 985
> Interlace
>
> # 800x600 @ 72 Hz, 48.0 kHz hsync
>
=== message truncated ===
__________________________________
Do you Yahoo!?
Yahoo! SiteBuilder - Free, easy-to-use web site design software
http://sitebuilder.yahoo.com
_______________________________________________
XFree86 mailing list
[EMAIL PROTECTED]
http://XFree86.Org/mailman/listinfo/xfree86
