I know this is nuts, but none of the tools I have can open the glst tarball. I do have 3 windows programs that handle tar's, but not this tar. Can someone reccomend a windows program that will unpack Davide's tarball on Windows - or perhaps someone could make the files available for me?
Tony ----- Original Message ----- From: "Rob Arends" <[EMAIL PROTECTED]> To: <[email protected]> Cc: "'Alan D. Snyder'" <[EMAIL PROTECTED]> Sent: Tuesday, February 14, 2006 12:25 AM Subject: [xmail] Re: glst changes? > Sure Alan, > > Below is my entire glst.conf > The main Tweaks were related to the large MTA pools - yahoo, hotmail, etc. > I ended up rounding everything to /24 bit with some exception to larger > networks (see Bigpond and Optus Australian ISPs) > I also excluded a whole heap of networks for familiar or trusted MTAs - > for > mailing lists primarily. > I also reduced the block time (timeo) to 7 minutes, because 60 minutes was > too long and most spammers were not retrying anyway, so 1 minute or 60 > minutes was about the same. > I just analysed my historical logs for IP addresses and trends; then after > glst implementation, I watched the glst filter rejections and saw the IPs > and trends and adjusted the mnet and xnet parameters. After some > complaints > I reduced the timeo. > This process took an hour or so each day for a few days . > > I also use in server.tab > "SMTP-MaxErrors" "3" > So that if I get dictionary attacked, then that door is closed too. > > And the other key ingredient in server.tab > "CustMapsList" > "list.dsbl.org.:0,relays.ordb.org.:0,sbl.spamhaus.org:0,bl.spamcop.net:0" > > I haven't checked recently if all the lists are active, but I've had no > reason to. > > I get _very_ little spam with this setup. > > Rob :-) > > > > <glst.conf> > rejmsg=451 4.7.1 Please try again later > generr=0 > rejerr=3 > timeo=420 > exptimeo=3110400 > lametimeo=28800 > > # Round all networks to match on ranges of 256 (last octet=*) > mnet=0.0.0.0,0.0.0.0,255.255.255.0 > > # BigPond - go for match on first 2 octects only > mnet=144.140.82.0,255.255.255.0,255.255.0.0 > mnet=144.140.83.0,255.255.255.0,255.255.0.0 > mnet=144.140.92.0,255.255.255.0,255.255.0.0 > mnet=144.140.93.0,255.255.255.0,255.255.0.0 > > # Optus - go for match on first 2 octects only > mnet=211.29.132.0,255.255.255.0,255.255.0.0 > mnet=211.29.133.0,255.255.255.0,255.255.0.0 > > # Hotmail > mnet=65.52.0.0,255.255.255.0,255.252.0.0 > mnet=64.4.0.0,255.255.255.0,255.255.192.0 > > # Yahoo mail > mnet=68.142.200.0,255.255.252.0,255.255.252.0 > > # mailguard.com.au > mnet=70.84.0.0,255.255.0.0,255.252.0.0 > mnet=66.235.184.61,255.255.255.255,255.255.255.0 > > # Exclude the following networks > # Local > xnet=127.0.0.1,255.255.255.255 > xnet=10.0.0.0,255.0.0.0 > xnet=172.16.0.0,255.240.0.0 > xnet=192.168.0.0,255.255.0.0 > # IMC > xnet=203.202.100.224,255.255.255.224 > xnet=203.202.8.0,255.255.255.0 > xnet=203.41.11.128,255.255.255.192 > # @lists.techtarget.com > xnet=65.214.43.171,255.255.255.255 > xnet=65.214.43.172,255.255.255.255 > xnet=65.214.43.174,255.255.255.255 > # @list.novell.com > xnet=130.57.1.68,255.255.255.255 > # @australiancu.com > net=203.58.62.33,255.255.255.255 > # @cav.asn.au > xnet=210.0.98.129,255.255.255.255 > # @list.cramsession.com > xnet=63.146.189.86,255.255.255.255 > # @newsletters.online.com (cNet) > xnet=206.16.1.130,255.255.255.255 > xnet=206.16.1.131,255.255.255.255 > xnet=206.16.1.161,255.255.255.255 > xnet=206.16.1.162,255.255.255.255 > xnet=206.16.1.190,255.255.255.255 > xnet=206.16.1.191,255.255.255.255 > # @nww.hdsmail.com > xnet=66.37.227.193,255.255.255.255 > # @qff.qantas.net.au > xnet=210.9.188.147,255.255.255.255 > # @groups.yahoo.com > xnet=66.94.237.0,255.255.255.0 > xnet=66.218.66.0,255.255.255.0 > xnet=209.73.160.0,255.255.255.0 > xnet=216.155.201.0,255.255.255.0 > # @myfamily.com > xnet=66.43.22.191,255.255.255.255 > xnet=66.43.22.192,255.255.255.255 > # @xmr3.com > xnet=205.183.255.0,255.255.255.0 > # @newsletters.online.com > xnet=206.16.1.131,255.255.255.255 > # @ebay.com > xnet=66.135.215.0,255.255.255.0 > > </glst.conf> > > > _____ > > From: Alan D. Snyder [mailto:[EMAIL PROTECTED] > Sent: Tuesday, February 14, 2006 11:18 AM > To: Rob Arends > Subject: glst changes? > > > Rob - what changes did you make to glst? > > care to share 'em? > > Thanks, > Alan > > > > > - > To unsubscribe from this list: send the line "unsubscribe xmail" in > the body of a message to [EMAIL PROTECTED] > For general help: send the line "help" in the body of a message to > [EMAIL PROTECTED] > > - To unsubscribe from this list: send the line "unsubscribe xmail" in the body of a message to [EMAIL PROTECTED] For general help: send the line "help" in the body of a message to [EMAIL PROTECTED]
