On Mon, Feb 16, 2009 at 5:27 PM, Keiji <[email protected]> wrote: > Hello to anyone who reads this (I haven't found if this is a mailing > list or a simple mailbox). > I have this motherboard with gentoo installed on it. A TV is connected > to the hdmi port and that's the only screen avaiable. > The screen is an hd-ready tv (1280x720). > > It used to work sometimes with fglrx (sometimes it gave a "blue screen > of no-signal") until today, when it ceased to work completely. > I am trying radeonhd and open source ati drivers, and so far ati gave > the better results (the blue screen goes away when X is killed - with > fglrx and radeonhd it remains until the powerdown) > > I have pastebins of various logs in different situation > starting situation: > http://pastebin.com/m25cfc832 > with EXA > http://pastebin.com/m6814ee32 > disabling DRI > http://pastebin.com/m23a8a8a3 > > My lspci: > 00:00.0 Host bridge: ATI Technologies Inc Device 7910 > 00:01.0 PCI bridge: ATI Technologies Inc Device 7912 > 00:07.0 PCI bridge: ATI Technologies Inc Device 7917 > 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA > 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) > 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) > 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) > 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) > 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) > 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) > 00:14.0 SMBus: ATI Technologies Inc SB600 SMBus (rev 13) > 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE > 00:14.2 Audio device: ATI Technologies Inc SB600 Azalia > 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge > 00:14.4 PCI bridge: ATI Technologies Inc SB600 PCI to PCI Bridge > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > HyperTransport Technology Configuration > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Address Map > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > DRAM Controller > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Miscellaneous Control > 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon X1200 Series > 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio > Controller > 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) > 03:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host > Controller (rev c0) > > Anyne has any idea?
(II) RADEON(0): Output HDMI-0 using initial mode 1920x540 The xserver is interpreting the EDID wrong. This mode should be 1920x1080 interlaced. You'll need to specify a modeline and a preferred mode to override the EDID. See this page for more info: http://wiki.debian.org/XStrikeForce/HowToRandR12 Also, the ati driver had issues on some chips with interlaced modes, so you may need to use the 6.11 RC (6.10.99) releases for interlaced output. Alex _______________________________________________ xorg-driver-ati mailing list [email protected] http://lists.x.org/mailman/listinfo/xorg-driver-ati
