The module sungem needs to be loaded after sungem_phy. -Felix On Thu, 2005-03-24 at 18:57 -0700, Bruce Woller wrote: > Hello Steve: > I have a G3 B&W 450 with a "GMAC(SUN GEM) Manufacturer:Apple Computer, > Driver: sungem, Device: /dev/eth0" according to the Hardware Browser. > I am using it to send this e-mail - I installed YDL4.0 straight out of > the box and eth0 just came up all on its own. I wonder if the driver > failed to install on your system? > > (Just so Terrasoft knows that not all G3s have a problem.) > > Bruce > On Fri, 2005-03-25 at 09:41, Steve Meyer wrote: > > Interesting new development... > > > > After three installs of YDL, I realized I was never prompted to > > selectDHCP or manual IP config. Now, with a different NIC (3Com) > > installed,and after running the YDL CD installation again, the NIC is > > listed andI get prompted to choose my IP configuration! So, the > > problem wasrelated to YDL/Fedora not recognizing the onboard NIC. > > This may beimportant for the Blue & White G3 "hardware supported" > > notes onTerrasoft's web site. > > > > Steve > > > > On Mar 25, 2005, at 9:31 AM, Steve Meyer wrote: > > > > From previous conversation... > > "SM> when I do 'ifconfig -a' I do not see a MAC address > > listed. > > ---------------------------------------------------------- > > Current conversation: > > RS> You don't see something like this? > > > > "eth0 Link encap:Ethernet HWaddr 00:0a:43:75:96:3A" > > > > > > No, I don't...no MAC address is listed. > > > > RS> "It should be... after you run ifup, 'service iptables > > status' (asroot) should > > show the firewall config.." > > > > When i ran 'ifup eth0' I get "configuration for eth0 not > > found."message. Yet in the GUI side 'System Settings/Network', > > the hardwaretab lists GMAC (Sun GEM) as eth0 and it says it's > > status is "ok". > > > > RS> "you can use tcpdump (as root) to watch traffic, to see if > > you aregetting dhcp > > replies.. > > > > tcpdump -l -i eth0" > > > > Again I have problems running tcpdump...I think this is due to > > thefact that there is no Ethernet card configured? The G3 Blue > > and Whitewas on the YDL supported hardware list with no issues > > regarding theonboard NIC. I would like to use the same NIC > > that works with Mac OSX but wonder if I should setup a > > different NIC in the computer so Ican network in > > Linux...however, that card will most likely not workwith OS X? > > > > Thanks for all your help, > > > > Steve > > > > > > > > > > > > > > Greetings, > > > > I have a Blue and White G3 (300Mhz) that is getting on > > the network(built in E-net) on the Mac OS X side but > > when I boot to Yellowdog Ifind I cannot browse via > > Mozilla...it's like my NIC is not getting anIP. I > > reinstalled Yellowdog and still have the problem. If > > I go toSystem Settings/Network and login at the prompt > > as root, under theHardware tab it shows "GMAC (Sun > > GEM) Ethernet eth0 ok". Any ideas? > > > > Thanks! > > > > _______________________________________________ > > yellowdog-general mailing list > > [email protected] > > > > http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general > > HINT: to Google archives, try > > '<keywords>site:terrasoftsolutions.com' > > > > > > > > ______________________________________________________________________ > > _______________________________________________ > > yellowdog-general mailing list > > [email protected] > > http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general > > HINT: to Google archives, try '<keywords> site:terrasoftsolutions.com' > > _______________________________________________ > yellowdog-general mailing list > [email protected] > http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general > HINT: to Google archives, try '<keywords> site:terrasoftsolutions.com'
_______________________________________________ yellowdog-general mailing list [email protected] http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general HINT: to Google archives, try '<keywords> site:terrasoftsolutions.com'
