On 13/05/2014 14:56, Robert P. J. Day wrote: > i finally have time to play with this, and am interested in using > yocto to build a bootable system for the galileo. i see that there is > a version "1.0.0" of the firmware for this board -- is there a > convenient yocto recipe that involves just downloading the layer info > and not what looks like the current entire tarball that's stuffed with > all the sources? i suspect that, within a day or two, i'll figure that > out once i start digging around. if it's already documented somewhere, > that would be even better. :-) rday
I've made some progress with this Robert, although I confess it was more challenging than I had expected. I suspect I am using components that are out of sync, maybe the installed grub loader vs the images I'm trying to build and boot, or perhaps because I'm trying to target a poky distribution instead of the iot one. Maybe I'm just missing something blindingly obvious and making a rod for my back. The Galileo didn't seem to want to play nicely from the start. I wasn't able to do the simple Arduino IDE firmware update the docs suggest - no response to query - and couldn't get any life out of UART0 on the TTL pins. The USB client was enumerating as a serial gadget once I copied across the 'magic' usbser.sys driver file on my Windows host though, so there was some proof of life at least. (I was a bit concerned for a while I might have bricked the thing when I spotted the caveats about not powering USB without +V from the PSU. Seems a bit like an accident waiting to happen, particularly if this is being marketed as an Arduino replacement. Big red sticker on the box needed for us software engineers at the very least). I finally realised that I needed to wire up a 3.5mm jack cable to see the Linux console (at RS232-C line levels no less....) A shame that wasn't included in the box, but I guess if you just want an Arduino-a-like (and the USB comms. actually works...) then maybe you don't need to see what's really going on. I worked through the Quark_BSPBuildGuide as it says that "you must update the firmware the first time you use the board", which has been superceded, so I wondered if maybe I was running some old code in the supplied board that needed updating. The capsule files from the LITTLE_LINUX_IMAGE_FirmwareUpdate_Intel_Galileo download installed OK and that got me to a shell with Poky 1.4 "Poky 9.0.2 (Yocto Project 1.4 Reference Distro) 1.4.2 clanton /dev/ttyS1" It was picking up an IP address, I could SSH in and all was good. ... So then I had a look at what was involved in booting from the uSD instead of the image that I presume the capsule installed to the SPI flash. As I mentioned earlier I had grabbed meta-intel-iot-devkit. Perhaps that was my mistake. I had built up an image with the packaged layers to start, and I then tried to copy across my new build so I could boot it. I was hoping for something a little like what is offered out of the meta-fsl-arm builds, i.e. a FAT boot partition and then an ext3 rootfs partition, but this layer seems to be using a single FAT partition with an initrd and an ext3 file mounted as root. First I tried dd'ing the .hddimg file I had generated but that seemed to result in an EFI boot configuration that the Galileo bootloader wasn't picking up. So I reverted to copying across my new bzImage and iot-devkit-image-clanton.ext3 as per the BSP Build docs and that at least did boot the kernel. It then failed to mount the rootfs as it couldn't find /media/realroot in the .ext3 file. Maybe this is because I'm targeting poky not the iot distro? With that added to my image I was able to boot to a Poky 1.5.1 shell, and I had mono 3.4.0 up and running on poky which was what I wanted to achieve. That said I seem to have lost the ethernet interface along the way so will need to see where that has gone. ... Lastly I've tried to eliminate use of the bblayers from meta-intel-iot-devkit in favour of my day to day Poky 1.6 daisy layers. I needed to copy across ./meta-intel-iot-devkit/meta/conf/machine/include/ia32-base.inc to poky/meta, remove dependencies on meta-iot-devkit and meta-hob from bblayers, and remove a couple of orphaned .bbappends in meta-galileo (iot-devkit-spi-image.bbappend, iot-devkit-image.bbappend) but it seems to be building now at least. I'm waiting to see how far that gets. ... Apologies for the length of this, but perhaps some of it is useful. If there's an easier way to build a poky daisy distro for Galileo I'd love to hear it :) Cheers, Alex -- _______________________________________________ yocto mailing list [email protected] https://lists.yoctoproject.org/listinfo/yocto
