Hmm, I built the same commits from your recipes, and I'm still getting the glx error in my logs :/
Other than that, things seem to work okay... Steve On Sat, May 27, 2017 at 9:20 PM, Trevor Woerner <[email protected]> wrote: > Hey Stephen, > > On Fri, May 26, 2017 at 7:23 PM, Stephen Arnold > <[email protected]> wrote: > > @Trevor what's your config/setup? Did you wind up using the > > "use-mainline-bsp" thing? > > Yes. > > As I mentioned, I was working with a wandboard, on master, therefore > my layers are: > - openembedded-core > - meta-freescale-3rdparty > - meta-freescale > > If I was working on some other board that didn't require > meta-freescale-3rdparty I wouldn't have needed that layer. > Additionally, I had started by using meta-etnaviv as well. That layer > hasn't seen any commits in roughly 10 months. Back then my guess is > that "upstream" didn't include very many of the bits required to get > this to work, therefore meta-etnaviv had to include recipes/bbappends > for mesa, libdrm, xorg-xserver, etc... in addition to the etnaviv drm > pieces themselves. > > I created my own clone of meta-etnaviv > [https://github.com/twoerner/meta-etnaviv] and pushed all my > commits/updates there with the intention of, eventually, sending a > pull request to its author. But by the time I was done removing all > the things that are no longer needed (i.e. all the bbappends, since > upstream mesa, libdrm, etc... all include the necessary bits) and > updating the remaining stuff, I was left with very little. So little, > in fact, that I decided to simply fold what was left back into > meta-freescale itself, conditional on the "use-mainline-bsp" > MACHINEOVERRIDES, and sent those patches to the meta-fsl mailing list. > > If the maintainers of meta-freescale accept the assumption that > use-mainline-bsp could be the flag that indicates interest between the > binary vivante drivers and etnaviv, then I hope they like the patches > and accept them into meta-freescale itself. Otherwise I could just > send that pull request to meta-etanviv's author (or re-work the > patches with whatever feedback I get). In any case, for wandboard > use-mainline-bsp is needed since the default kernel for wandboard is > linux-wandboard which is still stuck at 4.1.15 and is too old for this > etnaviv stuff. However using use-mainline-bsp with the wandboard is > broken, so I had to send some patches for that (u-boot and kernel) as > well (hopefully those patches are accepted as well). > > Due to the fact so much of etnaviv is already upstream, getting > etanviv working doesn't take very much. It just took me a while to > reach that point, however :-) > > > I pretty much had to hack up some of the meta-fsl/meta-boundary stuff and > > put everything else in local.conf. It would be a little easier/cleaner > if > > the former had some ?= in a few places... > > > > Anyway, I masked the browser stuff so I haven't tested that far yet, but > all > > you really need for 3D under X is new kernel/libdrm/mesa for ~110 fps > with > > glxgears. > > I like to use mesa-demos and (especially) glmark2 as my programs of > choice for testing GL stuff. > > > I added recipes for the x11-armada stuff, which seems to work for > > 2D but coughs an error in the xorg log. > > I'm curious to know which x11-armada stuff you're using. I couldn't > get the stuff that came with meta-etnaviv to compile so I looked > around and found Russell King's code which seemed more up-to-date, and > compiled. Plus my xorg log doesn't have any errors (see attachment). > > > I probably tested more with oe-core > > than poky but both should work. > > I just tend to stick with oe-core. > > I'm hoping to make a couple blog posts with my findings. >
[ 558.679] X.Org X Server 1.19.3 Release Date: 2017-03-15 [ 558.679] X Protocol Version 11, Revision 0 [ 558.679] Build Operating System: Linux 4.10.10-gentoo armv7l Gentoo [ 558.679] Current Operating System: Linux gencube 4.10.10-gentoo #1 SMP PREEMPT Sun Apr 23 05:44:04 PDT 2017 armv7l [ 558.679] Kernel command line: console=ttymxc0 root=PARTUUID=7d2c5159-01 ro rootfstype=ext4 rootwait video=HDMI-A-1:1024x768 net.ifnames=0 cma=384M console=tty1 ahci_imx.hotplug=1 [ 558.680] Build Date: 31 May 2017 03:00:40PM [ 558.680] [ 558.680] Current version of pixman: 0.34.0 [ 558.680] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 558.680] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 558.680] (==) Log file: "/var/log/Xorg.0.log", Time: Wed May 31 16:19:51 2017 [ 558.681] (==) Using config directory: "/etc/X11/xorg.conf.d" [ 558.681] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 558.681] (==) No Layout section. Using the first Screen section. [ 558.681] (==) No screen section available. Using defaults. [ 558.681] (**) |-->Screen "Default Screen Section" (0) [ 558.681] (**) | |-->Monitor "<default monitor>" [ 558.682] (==) No device specified for screen "Default Screen Section". Using the first device section listed. [ 558.682] (**) | |-->Device "Builtin Default fbdev Device 0" [ 558.682] (==) No monitor specified for screen "Default Screen Section". Using a default monitor configuration. [ 558.682] (==) Automatically adding devices [ 558.682] (==) Automatically enabling devices [ 558.682] (==) Automatically adding GPU devices [ 558.682] (==) Max clients allowed: 256, resource mask: 0x1fffff [ 558.682] (WW) The directory "/usr/share/fonts/TTF/" does not exist. [ 558.682] Entry deleted from font path. [ 558.682] (WW) The directory "/usr/share/fonts/OTF/" does not exist. [ 558.682] Entry deleted from font path. [ 558.682] (WW) The directory "/usr/share/fonts/Type1/" does not exist. [ 558.682] Entry deleted from font path. [ 558.682] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/". [ 558.682] Entry deleted from font path. [ 558.682] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/"). [ 558.682] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/". [ 558.682] Entry deleted from font path. [ 558.683] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/"). [ 558.683] (==) FontPath set to: /usr/share/fonts/misc/ [ 558.683] (==) ModulePath set to "/usr/lib/xorg/modules" [ 558.683] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 558.683] (II) Loader magic: 0x74d8f008 [ 558.683] (II) Module ABI versions: [ 558.683] X.Org ANSI C Emulation: 0.4 [ 558.683] X.Org Video Driver: 23.0 [ 558.683] X.Org XInput driver : 24.1 [ 558.683] X.Org Server Extension : 10.0 [ 558.684] (II) xfree86: Adding drm device (/dev/dri/card1) [ 558.687] (II) xfree86: Adding drm device (/dev/dri/card0) [ 558.687] (II) xfree86: Adding drm device (/dev/dri/card2) [ 558.687] (II) no primary bus or device found [ 558.687] falling back to /sys/devices/soc0/display-subsystem/drm/card1 [ 558.687] (II) Open APM successful [ 558.687] (II) LoadModule: "glx" [ 558.688] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 558.702] (II) Module glx: vendor="X.Org Foundation" [ 558.702] compiled for 1.19.3, module version = 1.0.0 [ 558.702] ABI class: X.Org Server Extension, version 10.0 [ 558.702] (II) LoadModule: "armada" [ 558.703] (II) Loading /usr/lib/xorg/modules/drivers/armada_drv.so [ 558.704] (II) Module armada: vendor="X.Org Foundation" [ 558.704] compiled for 1.19.3, module version = 0.0.0 [ 558.704] Module class: X.Org Video Driver [ 558.704] ABI class: X.Org Video Driver, version 23.0 [ 558.704] (II) armada: Support for Marvell LCD Controller: 88AP510 [ 558.704] (II) armada: Support for Freescale IPU: i.MX6 [ 558.704] (++) using VT number 7 [ 558.704] (II) armada(0): Added screen for KMS device /dev/dri/card1 [ 558.705] (II) armada(0): hardware: imx-drm [ 558.705] (II) armada(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 558.705] (==) armada(0): Depth 24, (--) framebuffer bpp 32 [ 558.705] (==) armada(0): RGB weight 888 [ 558.705] (==) armada(0): Default visual is TrueColor [ 558.705] (**) armada(0): Option "XvAccel" "TRUE" [ 558.705] (**) armada(0): Option "XvPreferOverlay" "TRUE" [ 558.705] (**) armada(0): Option "UseGPU" "TRUE" [ 558.705] (**) armada(0): Option "AccelModule" "etnadrm_gpu" [ 558.705] (II) Loading sub module "etnadrm_gpu" [ 558.705] (II) LoadModule: "etnadrm_gpu" [ 558.706] (II) Loading /usr/lib/xorg/modules/drivers/etnadrm_gpu.so [ 558.706] (II) Module Etnaviv GPU driver (DRM): vendor="X.Org Foundation" [ 558.706] compiled for 1.19.3, module version = 0.0.0 [ 558.706] ABI class: X.Org ANSI C Emulation, version 0.4 [ 558.707] (**) armada(0): Option "DRI" "TRUE" [ 558.740] (II) armada(0): Output HDMI1 has no monitor section [ 558.774] (II) armada(0): EDID for output HDMI1 [ 558.774] (II) armada(0): Manufacturer: TSB Model: 206 Serial#: 16843009 [ 558.774] (II) armada(0): Year: 2012 Week: 1 [ 558.774] (II) armada(0): EDID Version: 1.3 [ 558.774] (II) armada(0): Digital Display Input [ 558.774] (II) armada(0): Max Image Size [cm]: horiz.: 160 vert.: 90 [ 558.774] (II) armada(0): Gamma: 2.20 [ 558.774] (II) armada(0): No DPMS capabilities specified [ 558.774] (II) armada(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 [ 558.774] (II) armada(0): First detailed timing is preferred mode [ 558.774] (II) armada(0): redX: 0.640 redY: 0.335 greenX: 0.285 greenY: 0.605 [ 558.774] (II) armada(0): blueX: 0.150 blueY: 0.060 whiteX: 0.280 whiteY: 0.290 [ 558.774] (II) armada(0): Supported established timings: [ 558.774] (II) armada(0): 640x480@60Hz [ 558.774] (II) armada(0): 800x600@60Hz [ 558.774] (II) armada(0): 1024x768@60Hz [ 558.775] (II) armada(0): Manufacturer's mask: 0 [ 558.775] (II) armada(0): Supported standard timings: [ 558.775] (II) armada(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897 [ 558.775] (II) armada(0): #1: hsize: 1360 vsize 765 refresh: 60 vid: 49291 [ 558.775] (II) armada(0): Supported detailed timing: [ 558.775] (II) armada(0): clock: 148.5 MHz Image Size: 1600 x 900 mm [ 558.775] (II) armada(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0 [ 558.775] (II) armada(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0 [ 558.775] (II) armada(0): Supported detailed timing: [ 558.775] (II) armada(0): clock: 85.5 MHz Image Size: 1600 x 900 mm [ 558.775] (II) armada(0): h_active: 1360 h_sync: 1424 h_sync_end 1536 h_blank_end 1792 h_border: 0 [ 558.775] (II) armada(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 795 v_border: 0 [ 558.775] (II) armada(0): Monitor name: TOSHIBA-TV [ 558.775] (II) armada(0): Ranges: V min: 23 V max: 61 Hz, H min: 15 H max: 68 kHz, PixClock max 155 MHz [ 558.775] (II) armada(0): Supported detailed timing: [ 558.775] (II) armada(0): clock: 74.2 MHz Image Size: 1600 x 900 mm [ 558.775] (II) armada(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0 [ 558.775] (II) armada(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0 [ 558.775] (II) armada(0): Supported detailed timing: [ 558.775] (II) armada(0): clock: 74.2 MHz Image Size: 1600 x 900 mm [ 558.775] (II) armada(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0 [ 558.775] (II) armada(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0 [ 558.775] (II) armada(0): Supported detailed timing: [ 558.775] (II) armada(0): clock: 27.0 MHz Image Size: 1200 x 900 mm [ 558.776] (II) armada(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0 [ 558.776] (II) armada(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0 [ 558.776] (II) armada(0): Supported detailed timing: [ 558.776] (II) armada(0): clock: 27.0 MHz Image Size: 1200 x 900 mm [ 558.776] (II) armada(0): h_active: 1440 h_sync: 1478 h_sync_end 1602 h_blank_end 1716 h_border: 0 [ 558.776] (II) armada(0): v_active: 240 v_sync: 244 v_sync_end 247 v_blanking: 262 v_border: 0 [ 558.776] (II) armada(0): Number of EDID sections to follow: 1 [ 558.776] (II) armada(0): EDID (in hex): [ 558.776] (II) armada(0): 00ffffffffffff005262060201010101 [ 558.776] (II) armada(0): 0116010380a05a780af09da355499b26 [ 558.776] (II) armada(0): 0f474a21080081808bc0010101010101 [ 558.776] (II) armada(0): 010101010101023a801871382d40582c [ 558.776] (II) armada(0): 450040846300001e662150b051001b30 [ 558.776] (II) armada(0): 4070360040846300001e000000fc0054 [ 558.776] (II) armada(0): 4f53484942412d54560a2020000000fd [ 558.776] (II) armada(0): 00173d0f440f000a2020202020200194 [ 558.776] (II) armada(0): 02032671499001020304050607202609 [ 558.776] (II) armada(0): 0707110718830100006c030c00200000 [ 558.776] (II) armada(0): 21c015151f1f011d8018711c1620582c [ 558.776] (II) armada(0): 250040846300009e011d007251d01e20 [ 558.776] (II) armada(0): 6e28550040846300001e8c0ad08a20e0 [ 558.777] (II) armada(0): 2d10103e9600b084430000188c0aa014 [ 558.777] (II) armada(0): 51f01600267c4300b084430000980000 [ 558.777] (II) armada(0): 0000000000000000000000000000003f [ 558.777] (--) armada(0): HDMI max TMDS frequency 165000KHz [ 558.777] (II) armada(0): Printing probed modes for output HDMI1 [ 558.777] (II) armada(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP) [ 558.777] (II) armada(0): Modeline "1920x1080"x59.9 148.35 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.4 kHz e) [ 558.777] (II) armada(0): Modeline "1920x1080i"x60.0 74.25 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync (33.8 kHz e) [ 558.777] (II) armada(0): Modeline "1920x1080"x24.0 74.25 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e) [ 558.777] (II) armada(0): Modeline "1920x1080i"x59.9 74.18 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync (33.7 kHz e) [ 558.777] (II) armada(0): Modeline "1920x1080"x24.0 74.18 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz e) [ 558.777] (II) armada(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e) [ 558.777] (II) armada(0): Modeline "1360x768"x59.9 84.96 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.8 kHz) [ 558.777] (II) armada(0): Modeline "1360x768"x60.0 85.50 1360 1424 1536 1792 768 771 777 795 +hsync +vsync (47.7 kHz e) [ 558.777] (II) armada(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e) [ 558.777] (II) armada(0): Modeline "1280x720"x59.9 74.18 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e) [ 558.777] (II) armada(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 558.777] (II) armada(0): Modeline "1440x480i"x59.9 27.00 1440 1478 1602 1716 480 488 494 525 interlace -hsync -vsync (15.7 kHz e) [ 558.777] (II) armada(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 558.777] (II) armada(0): Modeline "720x480"x60.0 27.03 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e) [ 558.778] (II) armada(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e) [ 558.778] (II) armada(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 558.778] (II) armada(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 558.778] (II) armada(0): Output HDMI1 connected [ 558.778] (II) armada(0): Using exact sizes for initial modes [ 558.778] (II) armada(0): Output HDMI1 using initial mode 1920x1080 +0+0 [ 558.778] (==) armada(0): Using gamma correction (1.0, 1.0, 1.0) [ 558.778] (==) armada(0): DPI set to (96, 96) [ 558.778] (II) Loading sub module "fb" [ 558.778] (II) LoadModule: "fb" [ 558.778] (II) Loading /usr/lib/xorg/modules/libfb.so [ 558.780] (II) Module fb: vendor="X.Org Foundation" [ 558.780] compiled for 1.19.3, module version = 1.0.0 [ 558.780] ABI class: X.Org ANSI C Emulation, version 0.4 [ 558.781] (==) Depth 24 pixmap format is 32 bpp [ 558.804] (**) armada(0): Option "HWcursor" "TRUE" [ 558.804] (**) armada(0): Option "HotPlug" "TRUE" [ 558.805] (==) armada(0): Backing store enabled [ 558.805] (==) armada(0): Silken mouse enabled [ 558.805] (EE) armada(0): etnaviv: unable to open: Invalid argument [ 558.805] (WW) armada(0): [drm] Vivante initialization failed, running unaccelerated [ 558.805] (II) armada(0): No hardware cursor support - disabling hardware cursors [ 558.805] (II) armada(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 558.806] (==) armada(0): DPMS enabled [ 558.806] (**) armada(0): hotplug detection enabled [ 558.860] (--) RandR disabled [ 558.861] (II) AIGLX: Screen 0 is not DRI2 capable [ 558.861] (EE) AIGLX: reverting to software rendering [ 559.192] (II) IGLX: enabled GLX_MESA_copy_sub_buffer [ 559.194] (II) IGLX: Loaded and initialized swrast [ 559.194] (II) GLX: Initialized DRISWRAST GL provider for screen 0 [ 559.194] (II) armada(0): Setting screen physical size to 508 x 285 [ 559.338] (II) config/udev: Adding input device gpio-keys (/dev/input/event1) [ 559.338] (II) No input driver specified, ignoring this device. [ 559.338] (II) This device may have been added with another device file. [ 559.339] (II) config/udev: Adding input device gpio_ir_recv (/dev/input/event2) [ 559.340] (**) gpio_ir_recv: Applying InputClass "evdev keyboard catchall" [ 559.340] (II) LoadModule: "evdev" [ 559.340] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so [ 559.342] (II) Module evdev: vendor="X.Org Foundation" [ 559.342] compiled for 1.19.3, module version = 2.10.5 [ 559.342] Module class: X.Org XInput Driver [ 559.342] ABI class: X.Org XInput driver, version 24.1 [ 559.342] (II) Using input driver 'evdev' for 'gpio_ir_recv' [ 559.342] (**) gpio_ir_recv: always reports core events [ 559.342] (**) evdev: gpio_ir_recv: Device: "/dev/input/event2" [ 559.343] (--) evdev: gpio_ir_recv: Vendor 0x1 Product 0x1 [ 559.343] (--) evdev: gpio_ir_recv: Found keys [ 559.343] (II) evdev: gpio_ir_recv: Configuring as keyboard [ 559.343] (**) Option "config_info" "udev:/sys/devices/soc0/ir-receiver/rc/rc0/input2/event2" [ 559.343] (II) XINPUT: Adding extended input device "gpio_ir_recv" (type: KEYBOARD, id 6) [ 559.343] (**) Option "xkb_rules" "evdev" [ 559.346] (II) config/udev: Adding input device Logitech K400 (/dev/input/event0) [ 559.346] (**) Logitech K400: Applying InputClass "evdev pointer catchall" [ 559.346] (**) Logitech K400: Applying InputClass "evdev keyboard catchall" [ 559.347] (II) Using input driver 'evdev' for 'Logitech K400' [ 559.347] (**) Logitech K400: always reports core events [ 559.347] (**) evdev: Logitech K400: Device: "/dev/input/event0" [ 559.347] (--) evdev: Logitech K400: Vendor 0x46d Product 0x4024 [ 559.347] (--) evdev: Logitech K400: Found 20 mouse buttons [ 559.347] (--) evdev: Logitech K400: Found scroll wheel(s) [ 559.347] (--) evdev: Logitech K400: Found relative axes [ 559.347] (--) evdev: Logitech K400: Found x and y relative axes [ 559.347] (--) evdev: Logitech K400: Found absolute axes [ 559.347] (II) evdev: Logitech K400: Forcing absolute x/y axes to exist. [ 559.347] (--) evdev: Logitech K400: Found keys [ 559.347] (II) evdev: Logitech K400: Configuring as mouse [ 559.347] (II) evdev: Logitech K400: Configuring as keyboard [ 559.347] (II) evdev: Logitech K400: Adding scrollwheel support [ 559.348] (**) evdev: Logitech K400: YAxisMapping: buttons 4 and 5 [ 559.348] (**) evdev: Logitech K400: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200 [ 559.348] (**) Option "config_info" "udev:/sys/devices/soc0/soc/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb2/2-1/2-1:1.2/0003:046D:C52B.0003/0003:046D:4024.0004/input/input0/event0" [ 559.348] (II) XINPUT: Adding extended input device "Logitech K400" (type: KEYBOARD, id 7) [ 559.348] (**) Option "xkb_rules" "evdev" [ 559.349] (II) evdev: Logitech K400: initialized for relative axes. [ 559.349] (WW) evdev: Logitech K400: ignoring absolute axes. [ 559.349] (**) Logitech K400: (accel) keeping acceleration scheme 1 [ 559.349] (**) Logitech K400: (accel) acceleration profile 0 [ 559.349] (**) Logitech K400: (accel) acceleration factor: 2.000 [ 559.349] (**) Logitech K400: (accel) acceleration threshold: 4 [ 559.351] (II) config/udev: Adding input device Logitech K400 (/dev/input/mouse0) [ 559.351] (II) No input driver specified, ignoring this device. [ 559.351] (II) This device may have been added with another device file.
-- _______________________________________________ yocto mailing list [email protected] https://lists.yoctoproject.org/listinfo/yocto
