Am Dienstag 25 März 2008 19:42:53 schrieb Hans-Michael Staab:
> Hi,
>
> I am using the kernel 2.6.
>
> http://www.acmesystems.it/articles/00033/zydas.pdf
>
> I want to use the zydas 1211 USB WLAN dongle and I did it in the way
> mentioned in the documentation.
>
> $ ifconfig
>
> [EMAIL PROTECTED] /etc/conf.d]104#
> [EMAIL PROTECTED] /etc/conf.d]104# ifconfig
>
> eth0 Link encap:Ethernet HWaddr 00:40:8C:01:15:58
> inet addr:192.168.178.210 Bcast:192.168.178.255
> Mask:255.255.25
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:577 errors:0 dropped:0 overruns:0 frame:0
> TX packets:261 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:49283 (48.1 KiB) TX bytes:46654 (45.5 KiB)
> Interrupt:17 DMA chan:1
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>
> I expected a new interface device: eg. eth1 (for the zd1211)
>
> Jan 1 00:02:12 axis-00408c011558 kernel: |__ / _| _ \ / \ / ___|
> Jan 1 00:02:12 axis-00408c011558 kernel: / / | | | | | |/ _ \ \___ \
> Jan 1 00:02:12 axis-00408c011558 kernel: / /| |_| | |_| / ___ \ ___) |
> Jan 1 00:02:12 axis-00408c011558 kernel: /____\__, |____/_/ \_\____/
> Jan 1 00:02:12 axis-00408c011558 kernel: |___/
> Jan 1 00:02:12 axis-00408c011558 kernel: ZD1211B - version 2.16.0.0
> Jan 1 00:02:12 axis-00408c011558 kernel: vendor_id = 0ace
> Jan 1 00:02:12 axis-00408c011558 kernel: product_id = 1215
> Jan 1 00:02:12 axis-00408c011558 kernel: USB 1.1 Host
> Jan 1 00:02:12 axis-00408c011558 kernel: Release Ver = 4810
> Jan 1 00:02:12 axis-00408c011558 kernel: EEPORM Ver = 4810
>
>
> The kernel module was already loaded, but I cannot configure the
> missing network device.
>
> Any ideas?
>
> best regards Michael
>
>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Microsoft
> Defy all challenges. Microsoft(R) Visual Studio 2008.
> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
> _______________________________________________
> Zd1211-devs mailing list - http://zd1211.wiki.sourceforge.net/
> Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs

Hi,

have you tried to plug the card off and in again? Sometimes this brings the 
device up, which doesn't mean that it will work afterwards, but at least it 
may be there. 

Moreover it seems that you are using a different driver not the one that's in 
the kernel, if I understand the manual, that you linked to, correctly. So 
maybe you are asking the wrong people here.  

Greets
        Andreas

-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
Zd1211-devs mailing list - http://zd1211.wiki.sourceforge.net/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs

Reply via email to