Hi,
Steve please can you send us the next data to study the problem:
1º ethtool output of all interfaces
2º a screenshot of "Settings::Interfaces"
3º really which interfaces have link?
Also check if other information that ethtool shows is correct, for example
the speed
Maybe could be some problem with the driver, like Jean wrote you
Regards!
2011/12/6 jean delestre <[email protected]>
> not sure about these NICs precisely
>
> but in general avoid using Broadcom NICs on production servers
>
> i would rather plug another intel PCIe to make sure all is stable and
> under control
>
>
>
> 2011/12/6 Steve LePage <[email protected]>
>
>> I have found some more information on this issue…****
>>
>> ** **
>>
>> Here are the adaptors and chipsets:****
>>
>> ** **
>>
>> 02:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704
>> Gigabit Ethernet (rev 10)****
>>
>> 02:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704
>> Gigabit Ethernet (rev 10)****
>>
>> 0a:01.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet
>> Controller (Copper) (rev 01)****
>>
>> 0a:01.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet
>> Controller (Copper) (rev 01)****
>>
>> ** **
>>
>> The intel ones are on a pci card and work fine the on board Broadcom ones
>> don’t work. They can be configured but have the problems previously stated.
>> ****
>>
>> ** **
>>
>> ** **
>>
>> *From:* Steve LePage [mailto:[email protected]]
>> *Sent:* Tuesday, December 06, 2011 11:23 AM
>> *To:* [email protected]
>> *Subject:* [Zenloadbalancer-support] Interface issue****
>>
>> ** **
>>
>> I have my public interface eth0 setup with a public IP and have a default
>> gateway setup e.g.:****
>>
>> ** **
>>
>> ** **
>>
>> Eth0: 200.1.1.10/27****
>>
>> GW 200.1.1.1/27 (default GW)****
>>
>> ** **
>>
>> And this all works including the gui and I can add farms to it.****
>>
>> ** **
>>
>> Eth0/1 are on board and 2/3 are an Intel GE PCI adaptor which the linux
>> system and zen see.****
>>
>> I tried to setup an additional ip so I could have my farm traffic come in
>> one adaptor and go out another to maximize throughput so I set Eth1:****
>>
>> ** **
>>
>> Eth1:200.1.1.11/27****
>>
>> (No GW set so it should use default)****
>>
>> ** **
>>
>> The hopes here is I can bind a farm to the .11 and have packets coming in
>> to .11 and going out the default gw on eth0. The problem I have is Zen
>> states that when I setup eth1 with any IP address on any subnet that there
>> is no link detected. From the cmd line I ran ethool on the adaptor and here
>> are the results:****
>>
>> ** **
>>
>> -interface not setup in zen (ethtool reports link detected on eth1)****
>>
>> -interface setup in zen (ethtool reports link down now but if I run
>> ethtool in –t, test mode it sees the link and I can remotely ping the ip
>> binded to eth1)****
>>
>> ** **
>>
>> I checked and tried different ip’s including internal and its not an ip
>> conflict.****
>>
>> ** **
>>
>> Regardless if I can ping it or not zen always sees the link as down****
>>
>>
>> ------------------------------------------------------------------------------
>> Cloud Services Checklist: Pricing and Packaging Optimization
>> This white paper is intended to serve as a reference, checklist and point
>> of
>> discussion for anyone considering optimizing the pricing and packaging
>> model
>> of a cloud services business. Read Now!
>> http://www.accelacomm.com/jaw/sfnl/114/51491232/
>> _______________________________________________
>> Zenloadbalancer-support mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/zenloadbalancer-support
>>
>>
>
>
> ------------------------------------------------------------------------------
> Cloud Services Checklist: Pricing and Packaging Optimization
> This white paper is intended to serve as a reference, checklist and point
> of
> discussion for anyone considering optimizing the pricing and packaging
> model
> of a cloud services business. Read Now!
> http://www.accelacomm.com/jaw/sfnl/114/51491232/
> _______________________________________________
> Zenloadbalancer-support mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/zenloadbalancer-support
>
>
--
Load balancer distribution - Open Source Project
http://www.zenloadbalancer.com
Distribution list (subscribe): [email protected]
------------------------------------------------------------------------------
Cloud Services Checklist: Pricing and Packaging Optimization
This white paper is intended to serve as a reference, checklist and point of
discussion for anyone considering optimizing the pricing and packaging model
of a cloud services business. Read Now!
http://www.accelacomm.com/jaw/sfnl/114/51491232/
_______________________________________________
Zenloadbalancer-support mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/zenloadbalancer-support
