You should be able to use the zProperty zSnmpCommunity to set Zenoss to use the community of your choice.
This has worked in 2.2.4 for me. -- James Pulver Information Technology Area Supervisor LEPP Computer Group Cornell University 傅毅艺 wrote: > Hello, > > I faced the same problem as below, can anyone give me a suggestion? > many thanks!! > > > Derek Pham wrote: >>/ Patrick, > />/ I had a similar problem, so I'm hoping my fix applies to yours. I had to > />/ make sure the SNMP community name was understood by Zenoss. By default, > />/ Zenoss understands "public" and "private". If the community name on your > />/ device(s) are anything different than that (e.g. "publicreadonly"), > />/ Zenoss may not understand it. > />/ > />/ I fixed my issue by modifying the community name on my device to > />/ "public". I've had to do this for both Zenoss v1.0 & v1.0.1 (VM > />/ version). You may be able to fix it also by adding your customized > />/ community to the /Devices/zSnmpCommunities property before adding the > />/ device, I'm not sure. Does anyone know if this is a bug or feature in > />/ Zenoss? > />/ > />/ Hope that helps, > />/ Derek. > />/ > />/ > />/ -----Original Message----- > />/ From: zenoss-users-bounces at zenoss.org > <http://lists.zenoss.org/mailman/listinfo/zenoss-users> > />/ [mailto:zenoss-users-bounces at zenoss.org > <http://lists.zenoss.org/mailman/listinfo/zenoss-users>] On Behalf Of > />/ patrickm at garlic.com > <http://lists.zenoss.org/mailman/listinfo/zenoss-users> > />/ Sent: Monday, December 04, 2006 7:16 PM > />/ To: zenoss-users at zenoss.org > <http://lists.zenoss.org/mailman/listinfo/zenoss-users> > />/ Subject: [zenoss-users] Problems with setting a device to work with SNMP > />/ > />/ Hello all, > />/ > />/ I've been reading the wiki and the pdf documentation for the past 4 > />/ days, > />/ and I've been able to set up all my devices to check ping, but I had a > />/ question regarding SNMP and how to set it up if I want Zenoss to monitor > />/ my SNMP devices. > />/ > />/ I have a few Cisco 7206VXR routers and some wireless devices I want to > />/ monitor. I know they have SNMP, but I'm just not sure how to configure > />/ Zenoss to monitor them. I've read the guides, changed the protocol to > />/ both portscan and snmp, but when I try to add a device using snmp, I get > />/ this: > />/ > />/ 2006-12-04 19:11:25 CRITICAL zen.DeviceLoader no snmp > />/ found for ip > />/ xxx.xxx.xxx.xxx > />/ > />/ When I try to add a device using portscan, I get this: > />/ > />/ 2006-12-04 19:11:56 INFO zen.Device device name > />/ 'router1.foo.com' for ip > />/ 'xxx.xxx.xxx.xxx' > />/ 2006-12-04 19:11:56 INFO zen.Device setting status monitor > />/ to ['localhost'] > />/ 2006-12-04 19:11:56 INFO zen.Device setting performance > />/ monitor to localhost > />/ 2006-12-04 19:11:56 INFO zen.ZenModeler loading collector > />/ plugins > />/ from:/usr/local/zenoss/Products/DataCollector/plugins > />/ 2006-12-04 19:11:56 WARNING zen.ZenModeler no cmd plugins > />/ found for > />/ router1.foo.com > />/ 2006-12-04 19:11:56 INFO zen.ZenModeler snmp collection device > />/ router1.foo.com > />/ 2006-12-04 19:11:56 INFO zen.ZenModeler plugins: > />/ zenoss.snmp.HRFileSystemMap, zenoss.snmp.InterfaceMap, > />/ zenoss.snmp.NewDeviceMap, zenoss.snmp.HRSWInstalledMap, > />/ zenoss.snmp.HRSWRunMap, zenoss.snmp.DellDeviceMap, > />/ zenoss.snmp.DeviceMap, > />/ zenoss.snmp.DellCPUMap, zenoss.snmp.DellPCIMap, zenoss.snmp.CpuMap, > />/ zenoss.snmp.RouteMap, zenoss.snmp.HPCPUMap, > />/ zenoss.snmp.InformantHardDiskMap, zenoss.snmp.IpServiceMap, > />/ zenoss.snmp.HPDeviceMap > />/ 2006-12-04 19:11:56 WARNING zen.ZenModeler no portscan > />/ plugins found for > />/ router1.foo.com > />/ > />/ > />/ [a very very very long pause.... then this displays underneath the > />/ above] > />/ > />/ 2006-12-04 19:14:56 WARNING zen.ZenModeler client > />/ router1.foo.com timeout > />/ 2006-12-04 19:14:56 INFO zen.Device collected snmp > />/ information for device > />/ router1.foo.com > />/ 2006-12-04 19:14:56 INFO zen.DeviceLoader device > />/ router1.foo.com loaded! > />/ > />/ > />/ > />/ > />/ It seems I get no errors when I set the protocol to none. > />/ > />/ What am I doing wrong, or what am I missing? > />/ > />/ If I need to provide any more info, please let me know. > />/ > />/ Thanks in advance. > / > > > > > ------------------------------------------------------------------------ > 不加好友也能聊？试试MSN在线通！ 现在就试试！ <http://im.live.cn/imme/> > > > ------------------------------------------------------------------------ > > _______________________________________________ > zenoss-users mailing list > [email protected] > http://lists.zenoss.org/mailman/listinfo/zenoss-users _______________________________________________ zenoss-users mailing list [email protected] http://lists.zenoss.org/mailman/listinfo/zenoss-users
