I've tried to leave the wanpipe configuration as vanilla as possible. I just turned of the hardware HDLC (that is because I've been told that if Hardware HDLC turned off, Sangoma cards are 100% compatible with digium/tormenta2 cards).
Here is my wanpipe configuration: [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 14 PCIBUS = 0 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 2 TE_CLOCK = NORMAL ACTIVE_CH = ALL TE_HIGHIMPEDANCE = NO INTERFACE = V35 CLOCKING = EXTERNAL BaudRate = 0 MTU = 1500 UDPPORT = 9000 TTL = 255 IGNORE_FRONT_END = NO [w1g1] PROTOCOL = HDLC HDLC_STREAMING = NO ACTIVE_CH = ALL IDLE_FLAG = 0x7E MTU = 1500 MRU = 1500 TDMV_SPAN = 1 TDMV_ECHO_OFF = NO MULTICAST = NO TRUE_ENCODING_TYPE = NO Any hints? Regards, Mabio Coelho -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Steve Underwood Sent: sexta-feira, 11 de novembro de 2005 15:14 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Problems with MFC/R2 in Brazil Mabio Coelho wrote: >Steve, > >The line is good, because we looped in my end and everything is ok. > >Regarding the card, it might be faulty, but I doubt it because I've tested >with two cards. > >My config files might be broken, that is why I've posted my config files in >my previous post but it got stripped by the list. So there we go: > > >Zaptel.conf: ># Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit ># Zaptel Configuration File ># ># This file is parsed by the Zaptel Configurator, ztcfg ># > ># It must be in the module loading order > > ># Span 1: WPE1/0 "wanpipe1 card 0" HDB3/ RED >span=1,1,0,cas,hdb3 >span=2,2,0,cas,hdb3 ># >cas=1-15:1101 >#dchan=16 >cas=17-31:1101 >#bchan=1-15,17-31:1101 ># >cas=32-46:1101 >#dchan=47 >cas=48-62:1101 > ># Span 3: WCTDM/0 "Wildcard TDM400P REV I Board 1" >fxoks=63 >fxoks=64 >fxsks=65 >fxsks=66 >##alaw=63-66 >##fxoks=32 >##fxoks=33 >##fxsks=34 >##fxsks=35 > ># Global data >loadzone = br >defaultzone = br > >I think that is the only file needed right? > >Thanks for the quick feedback. > >Mabio Coelho > > > If you are using a wanpipe card you need to get the wanpipe config files right too. Steve _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users