Michael Collins wrote: >Ken, > >The zaptel.conf looks good as far as I can tell. The only question I >have is on the Zapata.conf - do you know for sure that the switchtype is >supposed to be national? Just curious. My telco's are all set for >4ess/5ess or dms100. > > Yah, it is national -- not that that kept me from trying everything else for the hell of it. (I tried, in order, national, ni1, 4ess and 5ess. None worked, but national -- which is what they told me the switch was, to start with -- came by far the closest.)
>Second, can you do a "debug pri span 1" from the CLI and see what the >output is? I'm assuming that there's at least *some* communication on >the D-channel since you're able to get inbound calls. I'm just curious >to know what's happening on the D channel when you are dialing out. > > I can't. It was a one-shot deal, as (because of the phone company) I can only get the T1 turned to ISDN during work hours, which means that my company's lines are down while I'm trying to switch over. I realized about 1 minute after I told them to revert that I should have gotten a "debug pri" dump, but it was too late. -Ken >-MC > >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED] On Behalf Of Ken >D'Ambrosio >Sent: Thursday, February 16, 2006 1:51 PM >To: Asterisk Users Mailing List - Non-Commercial Discussion >Cc: [EMAIL PROTECTED] >Subject: [Asterisk-Users] "No D-channels available!" > >I just tried to go from CAS to PRI on my T1 (Sangoma), and failed pretty >badly. Seemingly everything worked -- Asterisk would see the incoming >call (including CID and DID info), try to route it, and fail -- giving >me a telco (not Asterisk) call failure message. My zapata.conf and >zaptel.conf files are at http://pastebin.com/558349 > >Below's the log dump. > >Note that, because I was simply going from CAS to PRI, I don't believe >the span definition line, itself, should have changed. > >If anyone has any ideas, I'd sure be interested... > >-- Accepting call from '1234567890' to '1630' on channel 0/1, span 1 >Enabled echo cancellation on channel 1 >-- Executing Goto("Zap/1-1", "internal|1630|1") in new stack >-- Goto (internal,1630,1) >-- Executing Dial("Zap/1-1", "SIP/1630|18") in new stack >Setting NAT on RTP to 0 >Outgoing Call for 1630 >-- Called 1630 >(Provisional) Stopping retransmission (but retaining packet) on >'[EMAIL PROTECTED]' Request 102: Found >-- SIP/1630-9ce0 is ringing >Requested indication 3 on channel Zap/1-1 >!! Got reject for frame 0, retransmitting frame 0 now, updating n_r! >!! Got reject for frame 0, retransmitting frame 1 now, updating n_r! >Echo cancellation already on >== Primary D-Channel on span 1 down >No D-channels available! Using Primary channel 24 as D-channel anyway! >== Primary D-Channel on span 1 up >update_call_counter(1630) - decrement call limit counter > > >_______________________________________________ >--Bandwidth and Colocation provided by Easynews.com -- > >Asterisk-Users mailing list >To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >_______________________________________________ >--Bandwidth and Colocation provided by Easynews.com -- > >Asterisk-Users mailing list >To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users