Thanks Steve -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Steve Underwood Sent: Wednesday, February 22, 2006 6:27 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Tormenta CAS signaling
Viktor Tatianin wrote: >Hi Steve > > >May I change TX ABCD bits 0101 to 1001 or no ? > > Not when you use fxols. You can only control them when you use cas as the signalling type. Steve >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED] Behalf Of Steve Underwood >Sent: Wednesday, February 22, 2006 3:28 PM >To: Asterisk Users Mailing List - Non-Commercial Discussion >Subject: Re: [Asterisk-Users] Tormenta CAS signaling > > >Hi Viktor, > >So? You seem to have 5 channels set to fxols mode OK. What exactly that >does, I am not sure. FXO operation is highly telco dependent with E1s. I >believe what is implemented in zaptel is an arrangement to work with >some E1 channel banks. > >Do you have an actual question this time? > >Steve > > >Viktor Tatianin wrote: > > > >>Hi Steve >>I have next config >>zttool >> >>Current Alarms: No alarms. >>Sync Source: Tormenta 2 (PCI) Quad E1 Card >>IRQ Misses: 0 >>Bipolar Viol: 14 >>Tx/Rx Levels: 0/ 0 >> >>Total/Conf/Act: 31/ 6/ 6 >> 1111111111222222222333 >>1234567890123456789012345789012 >> >> TxA 000000 >> TxB 111111 >> TxC 000000 >> TxD 111111 >> >> RxA 111111 >> RxB 011111 >> RxC 011111 >> RxD 111111 >> >> >> >> >> >> >> >>ztcfg -vv >> >>Zaptel Configuration >>====================== >> >>SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) >>SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) >> >>Channel map: >> >>Channel 01: Clear channel (Default) (Slaves: 01) >>Channel 02: Clear channel (Default) (Slaves: 02) >>Channel 03: Clear channel (Default) (Slaves: 03) >>Channel 04: Clear channel (Default) (Slaves: 04) >>Channel 05: Clear channel (Default) (Slaves: 05) >>Channel 06: Clear channel (Default) (Slaves: 06) >>Channel 07: Clear channel (Default) (Slaves: 07) >>Channel 08: Clear channel (Default) (Slaves: 08) >>Channel 09: Clear channel (Default) (Slaves: 09) >>Channel 10: Clear channel (Default) (Slaves: 10) >>Channel 11: Clear channel (Default) (Slaves: 11) >>Channel 12: Clear channel (Default) (Slaves: 12) >>Channel 13: Clear channel (Default) (Slaves: 13) >>Channel 14: Clear channel (Default) (Slaves: 14) >>Channel 15: Clear channel (Default) (Slaves: 15) >>Channel 16: D-channel (Default) (Slaves: 16) >>Channel 17: Clear channel (Default) (Slaves: 17) >>Channel 18: Clear channel (Default) (Slaves: 18) >>Channel 19: Clear channel (Default) (Slaves: 19) >>Channel 20: Clear channel (Default) (Slaves: 20) >>Channel 21: Clear channel (Default) (Slaves: 21) >>Channel 22: Clear channel (Default) (Slaves: 22) >>Channel 23: Clear channel (Default) (Slaves: 23) >>Channel 24: Clear channel (Default) (Slaves: 24) >>Channel 25: Clear channel (Default) (Slaves: 25) >>Channel 26: Clear channel (Default) (Slaves: 26) >>Channel 27: Clear channel (Default) (Slaves: 27) >>Channel 28: Clear channel (Default) (Slaves: 28) >>Channel 29: Clear channel (Default) (Slaves: 29) >>Channel 30: Clear channel (Default) (Slaves: 30) >>Channel 31: Clear channel (Default) (Slaves: 31) >>Channel 32: FXO Loopstart (Default) (Slaves: 32) >>Channel 33: FXO Loopstart (Default) (Slaves: 33) >>Channel 34: FXO Loopstart (Default) (Slaves: 34) >>Channel 35: FXO Loopstart (Default) (Slaves: 35) >>Channel 36: FXO Loopstart (Default) (Slaves: 36) >>Channel 37: FXO Loopstart (Default) (Slaves: 37) >> >>37 channels configured. >> >>this is zaptel.conf >> >>; Zapata telephony interface >>; >>; Configuration file >> >>[trunkgroups] >> >>[channels] >> >>language=en >>context=from-isdn-external >>;signalling=fxs_ks >>;rxwink=300 ; Atlas seems to use long (250ms) winks >>signalling=pri_cpe >>switchtype=euroisdn >>pridialplan=unknown >>prilocaldialplan=unknown >>callerid=asreceived >>usedistinctiveringdetection=yes >>usecallingpres=yes >> >>; Whether or not to do distinctive ring detection on FXO lines >>; >>;usedistinctiveringdetection=yes >> >>usecallerid=yes >>hidecallerid=no >>callwaiting=yes >>usecallingpres=yes >>callwaitingcallerid=yes >>threewaycalling=yes >>transfer=yes >>cancallforward=yes >>callreturn=yes >>echocancel=yes >>echocancelwhenbridged=yes >>echotraining=400 >>rxgain=0.0 >>txgain=0.0 >>group=0 >>callgroup=1 >>pickupgroup=1 >>immediate=no >> >>;faxdetect=both >>faxdetect=incoming >>;faxdetect=outgoing >>;faxdetect=no >> >>;Include genzaptelconf configs >>#include zapata-auto.conf >> >>;Include AMP configs >>#include zapata_additional.conf >>channel=> 1-15,17-31 >> >>signalling=fxo_ks >>context=bank >>group=1 >>cas=32-37:1101 >>channel=> 32-37 >>This is my zapata.conf >> >># Global data >> >>span=1,1,0,ccs,hdb3 >>bchan=1-15,17-31 >>dchan=16 >> >>loadzone = us >>defaultzone = us >> >>span=2,1,0,cas,hdb3 >>fxols=32-37 >> >> >> >> >>-----Original Message----- >>From: [EMAIL PROTECTED] >>[mailto:[EMAIL PROTECTED] Behalf Of Steve >> >> >Underwood > > >>Sent: Tuesday, February 21, 2006 2:59 PM >>To: Asterisk Users Mailing List - Non-Commercial Discussion >>Subject: Re: [Asterisk-Users] Tormenta CAS signaling >> >> >>Viktor Tatianin wrote: >> >> >> >> >> >>>Hi Steve >>> >>>I attempt change in zapata.conf >>> >>>cas=1-15:1101 but use zttool view ABCD bits 1010 >>> >>>Regards, >>>Viktor >>> >>> >>> >>> >>> >>> >>Have you put the E1 in CAS mode with something like: >> >>span=1,1,0,cas,hdb3 >> >>Steve >> >> >> >> >> >>>-----Original Message----- >>>From: [EMAIL PROTECTED] >>>[mailto:[EMAIL PROTECTED] Behalf Of Steve >>> >>> >>> >>> >>Underwood >> >> >> >> >>>Sent: Friday, February 10, 2006 3:25 PM >>>To: Asterisk Users Mailing List - Non-Commercial Discussion >>>Subject: Re: [Asterisk-Users] Tormenta CAS signaling >>> >>> >>>Viktor Tatianin wrote: >>> >>> >>> >>> >>> >>> >>> >>>>Hello >>>> >>>>Can anyone know how may change(inverting) cas signaling ABCD bits at the >>>>Tormenta 2 (four E1 ports) cards >>>>My cards send idle code ABCD 0101 but my mux which use as channel bank >>>> >>>> >>>> >>>> >>wait >> >> >> >> >>>>ABCD 1001 >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>The idle code is set in zapata.conf. For example: >>> >>>cas=1-15:1101 >>> >>>Sets CAS mode for channels 1 to 15, with the idle pattern 1101. >>> >>>Regards, >>>Steve >>> >>> >>> >>> >>> >>> _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users