May be i can help.
Sou Português:)
On 10/29/06, Pedro Silva <
[EMAIL PROTECTED]> wrote:
Thanks Alberto!
I tested with telsampl like you said (with various configurations for
de diva) and this not works...:(
The trace is:
Enter destination address: 273xxxxxx
<--Conn_Req(273xxxxxx)
Connect_Con-->
[29]:Disc_Ind-->
<--Disc_Res
**********Call cleared***********
Any idea for the possible problem?
Thanks and best regards,
PS.
2006/10/29, Alberto Pastore <[EMAIL PROTECTED]>:
> Pedro Silva ha scritto:
> > Hello,
> >
> > I need to connect one diva server 4bri to a portuguese BRI interface.
> > The operator (PT) said that this bri is in point-to-multipoint mode
> > (S0). Previously one PBX has connected to that interface.
> > The asterisk and diva drivers are working ok but i cannot communicate
> > to outside via this bri. Xlite gives me the message: "call failed:
> > declined".
> > Anyone have experience with this setup?
> > What are the main parameters for bri card configuration?
> > D-channel protocol: ETSI-DSS1 or other?
> > Interface mode: NT or TE?
> > Direct Inward Dialing (DID): Yes ou no? (MSN ou DID?)
> >
> > Thanks by any kind of help!
> > Best regards,
> > PS.
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > asterisk-users mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> I'm not sure about Portuguese operators standard, but I bet
> ETSI-DSS1 should work just fine. The interface mode is surely
> TE.
> The DID/MSN should not affect outgoing calls, I generally leave DID
> off unless the telco company has that service active.
>
> If you're using the diva server for linux package from eicon
> (divas4linux, currently rel. 8.2), you should find a very
> simple utility named "telsampl" under /usr/lib/eicon/divas
> which you can run besides asterisk, to test outgoing calls.
>
> You should run it with this command line: "telsampl -c x"
> where x is the bri port you wish to test (1..4)
> then at the prompt type "c" and enter a pstn number, e.g.
> your mobile phone, then you can watch the log onscreen.
>
> If the outgoing call works, then your isdn setup is correct,
> and the problem is in asterisk. The message from xlite is not
> meaningful, as it could occur on many situations.
> You should watch the debug output on asterisk console.
>
> That helped me a lot.
>
> Alberto.
>
>
> --
> --
> Alberto Pastore
> B-Press Srl - Gruppo MSoft
> P.IVA 01697420030
> P.le Lombardia, 4 - 28100 Novara - Italy
> Tel. 0321-499508
> Fax 0321-492974
> http://www.msoft.it
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
Com os melhores cumprimentos,
Marco Mouta
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
