Here's a silly question, if these are standard POTS you obviously know which number corresponds to which line, being the case couldn't you tell that ZAP/1 is POTS 555-1234, ZAP/2 is POTS 555-1235, etc etc?
I'm assuming you're trying to identify the inbound number from the telco that was dialed. Unless you have the lines in a hunt group at the telco, but then you're implying you don't care which number was dialed, you just want failover at the telco. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Rob Schall Sent: Wednesday, May 23, 2007 8:19 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] FXS + Pots Extensions Help We wanted a cheap last resort fail-over. A few really cheap pots lines are easy to run buy, as we can get them for a really low cost. My understanding with DIDs (and its limited), is they have to belong to a PRI. The only way that is cheaper than a few pots lines is if you needed 8 or more pots lines. Then the line fees balance out. I was hoping for a solution more along the lines of.... Use this "x" variable that contains what ZAP channel it came in on, then I can program that one to point to a particular person. Thanks, Rob Sean M. Pappalardo wrote: > > > Rob Schall wrote: >> Normally I just use pri's with our asterisk systems, but a request came >> in to add some normal pots lines to the setup. We have 3 lines, and they >> run into the fxs ports. They hit the dialplan just fine, and they always >> dial the "s" extension. However, my question would be... Is there a way >> to determine what number was dialed and have it forward to a specific >> phone? > > Sure, it's called a DID trunk. It's basically just a regular analog > phone line but the CO switch sends down the digits dialed in one of a > few ways: Dial pulse (DP), Multi-freq (MF), Dual-tone multi-frequency > (DTMF). They are usually inbound-only, but some CO's can add outbound > service too if needed. Call your phone service provider's business > office and ask about analog DID lines/trunks. They should be around > $30/mo for the line and $1-2/mo for each number. Ask them what type of > signaling they use then you'll need to configure your zapata.conf to > match. After that, you can then start routing in the dialplan based on > the number called. For extra fun, have the CO set them up in a hunt > group to avoid busy signals. > > Take a look at: http://www.voip-info.org/wiki-Asterisk+tips+DID > > (BTW, Why are you adding analog lines if you're already big enough for > a PRI? Isn't it less expensive to just add a couple more DID numbers > to the PRI?) > > Sean > > <<--------------------------------------------------------------------------------->> > > This E-Mail message has been scanned for viruses > and cleared by >>SmartMail<< from Smarter Technology, Inc. > <<--------------------------------------------------------------------------------->> > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. This e-mail, facsimile, or letter and any files or attachments transmitted with it contains information that is confidential and privileged. This information is intended only for the use of the individual(s) and entity(ies) to whom it is addressed. If you are the intended recipient, further disclosures are prohibited without proper authorization. If you are not the intended recipient, any disclosure, copying, printing, or use of this information is strictly prohibited and possibly a violation of federal or state law and regulations. If you have received this information in error, please notify Texas Health Management Group immediately at 1-817-310-4999. Texas Health Management Group, its subsidiaries, and affiliates hereby claim all applicable privileges related to this information. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
