Try connecting to the serial port on both boxes and setting the name on both, and then retrying the sync.
---- Matthew Huff | One Manhattanville Rd OTA Management LLC | Purchase, NY 10577 http://www.ox.com | Phone: 914-460-4039 aim: matthewbhuff | Fax: 914-460-4139 > -----Original Message----- > From: cisco-nsp-boun...@puck.nether.net [mailto:cisco-nsp- > boun...@puck.nether.net] On Behalf Of Jeff Wojciechowski > Sent: Thursday, June 11, 2009 12:38 PM > To: cisco-nsp@puck.nether.net > Subject: [c-nsp] ASA 5510 Configuration Replication Failure > > Dearest List: > > We are building a new active/standby ASA cluster with 5510's and the > initial config synch went just fine. > > However, when we changed the hostname on the primary unit and did a > 'write standby' I got the following: > > VaultASA(config)# wr stan > Building configuration... > [OK] > VaultASA(config)# Beginning configuration replication: Sending to mate. > Failover LAN Failed > Configuration Replication Failure > sh ver > > Cisco Adaptive Security Appliance Software Version 8.0(3) > Device Manager Version 6.1(5) > > Another interesting point about this is that both units show the synch > interface (E0/3 on both units in our case) show line protocol down. > > VaultASA(config)# sh int e0/3 > Interface Ethernet0/3 "failover", is down, line protocol is down > Hardware is i82546GB rev03, BW 100 Mbps, DLY 100 usec > Full-Duplex, 100 Mbps > Description: LAN/STATE Failover Interface > MAC address 0024.14d3.7b37, MTU 1500 > IP address x.x.x.x, subnet mask 255.255.255.0 > 558 packets input, 49468 bytes, 0 no buffer > Received 3 broadcasts, 0 runts, 0 giants > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 0 L2 decode drops > 499 packets output, 71296 bytes, 0 underruns > 0 output errors, 0 collisions, 9 interface resets > 0 babbles, 0 late collisions, 0 deferred > 0 lost carrier, 0 no carrier > input queue (curr/max packets): hardware (0/25) software (0/0) > output queue (curr/max packets): hardware (0/0) software (0/0) > Traffic Statistics for "failover": > 558 packets input, 39264 bytes > 502 packets output, 59800 bytes > 0 packets dropped > 1 minute input rate 0 pkts/sec, 0 bytes/sec > 1 minute output rate 0 pkts/sec, 0 bytes/sec > 1 minute drop rate, 0 pkts/sec > 5 minute input rate 0 pkts/sec, 0 bytes/sec > 5 minute output rate 0 pkts/sec, 0 bytes/sec > 5 minute drop rate, 0 pkts/sec > VaultASA(config)# > > Ideas? > > Thanks in advance. > > Jeff > _______________________________________________ > cisco-nsp mailing list cisco-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/
smime.p7s
Description: S/MIME cryptographic signature
_______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/