Package: linux-image-2.6.29-1-686 Version: 2.6.29-1 Severity: important Today I upgraded my Debian unstable. I installed new kernel 2.6.29 and udev 9.140. After that during boot ATI framebuffer is enabled (I am not sure if it is related - I have ATI Radeon).
Now, when I put DVD into my burnen (I have only one DVD drive) entire system hangs, and kernel panics. It blinks scroll and caps lock, but not num-lock. Panic occurs both when in X or in text mode. It occurs about five seconds after CD-tray closes. I haven't tested whether kernel would panic when I put blank CD or DVD. -- Package-specific info: ** Version: Linux version 2.6.29-1-686 (Debian 2.6.29-1) ([email protected]) (gcc version 4.3.3 (Debian 4.3.3-5) ) #1 SMP Tue Mar 24 23:05:52 UTC 2009 ** Command line: root=/dev/hda1 ro selinux=1 audit=0 enforcing=0 ** Not tainted ** Kernel log: [ 5.280494] libata version 3.00 loaded. [ 5.314660] ide-gd driver 1.18 [ 5.314806] hda: max request size: 512KiB [ 5.329671] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63 [ 5.329916] hda: cache flushes supported [ 5.330082] hda:<6>ide-cd driver 5.00 [ 5.332565] hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 > [ 5.419022] ide-cd: hdc: ATAPI 48X DVD-ROM DVD-R/RAM CD-R/RW drive, 2048kB Cache [ 5.419292] Uniform CD-ROM driver Revision: 3.20 [ 6.073304] PM: Starting manual resume from disk [ 6.118573] EXT3-fs: INFO: recovery required on readonly filesystem. [ 6.119272] EXT3-fs: write access will be enabled during recovery. [ 6.192524] kjournald starting. Commit interval 5 seconds [ 6.192615] EXT3-fs: recovery complete. [ 6.193033] EXT3-fs: mounted filesystem with ordered data mode. [ 7.611938] udev: starting version 140 [ 7.954658] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 7.954741] ACPI: Power Button (FF) [PWRF] [ 7.954903] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 [ 7.954970] ACPI: Power Button (CM) [PWRB] [ 7.975760] Linux agpgart interface v0.103 [ 7.988430] agpgart: Detected VIA KT400/KT400A/KT600 chipset [ 7.999233] agpgart-via 0000:00:00.0: AGP aperture is 128M @ 0xd0000000 [ 8.023621] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 8.082462] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 8.271515] NET: Registered protocol family 23 [ 8.308588] usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17 [ 8.308699] usbcore: registered new interface driver usblp [ 8.400303] radeonfb 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 8.401812] radeonfb: Found Intel x86 BIOS ROM Image [ 8.401868] radeonfb: Retrieved PLL infos from BIOS [ 8.401920] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=250.00 Mhz, System=200.00 MHz [ 8.401983] radeonfb: PLL min 20000 max 40000 [ 8.540282] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 8.689168] i2c-adapter i2c-2: unable to read EDID block. [ 8.841162] i2c-adapter i2c-2: unable to read EDID block. [ 8.993166] i2c-adapter i2c-2: unable to read EDID block. [ 9.145141] i2c-adapter i2c-3: unable to read EDID block. [ 9.297129] i2c-adapter i2c-3: unable to read EDID block. [ 9.449127] i2c-adapter i2c-3: unable to read EDID block. [ 9.505082] radeonfb: Monitor 1 type DFP found [ 9.505145] radeonfb: EDID probed [ 9.505192] radeonfb: Monitor 2 type no found [ 9.516130] Console: switching to colour frame buffer device 210x65 [ 9.578952] radeonfb (0000:01:00.0): ATI Radeon 4966 "If" [ 10.041933] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22 [ 10.042047] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 [ 10.042139] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22 [ 10.042625] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64 [ 11.104657] Adding 2008084k swap on /dev/hda9. Priority:-1 extents:1 across:2008084k [ 11.318104] EXT3 FS on hda1, internal journal [ 12.268128] fuse init (API version 7.11) [ 12.360134] device-mapper: uevent: version 1.0.3 [ 12.360463] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected] [ 19.557582] kjournald starting. Commit interval 5 seconds [ 19.559201] EXT3 FS on hda5, internal journal [ 19.560545] EXT3-fs: mounted filesystem with ordered data mode. [ 19.579007] kjournald starting. Commit interval 5 seconds [ 19.580646] EXT3 FS on hda6, internal journal [ 19.581939] EXT3-fs: mounted filesystem with ordered data mode. [ 19.595383] kjournald starting. Commit interval 5 seconds [ 19.597036] EXT3 FS on hda7, internal journal [ 19.598323] EXT3-fs: mounted filesystem with ordered data mode. [ 19.632368] kjournald starting. Commit interval 5 seconds [ 19.633956] EXT3 FS on hda8, internal journal [ 19.635234] EXT3-fs: mounted filesystem with ordered data mode. [ 19.716243] kjournald starting. Commit interval 5 seconds [ 19.717790] EXT3 FS on hda10, internal journal [ 19.719056] EXT3-fs: mounted filesystem with ordered data mode. [ 19.774505] kjournald starting. Commit interval 5 seconds [ 19.776202] EXT3 FS on hda11, internal journal [ 19.777450] EXT3-fs: mounted filesystem with ordered data mode. [ 19.970964] kjournald starting. Commit interval 5 seconds [ 19.973703] EXT3 FS on hda12, internal journal [ 19.974956] EXT3-fs: mounted filesystem with ordered data mode. [ 21.807741] eth0: link up, 10Mbps, half-duplex, lpa 0x0000 [ 24.621913] NET: Registered protocol family 10 [ 24.624215] lo: Disabled Privacy Extensions [ 34.956057] eth0: no IPv6 routers present [ 37.148356] Bluetooth: Core ver 2.14 [ 37.149772] NET: Registered protocol family 31 [ 37.151035] Bluetooth: HCI device and connection manager initialized [ 37.152286] Bluetooth: HCI socket layer initialized [ 37.242499] Bluetooth: L2CAP ver 2.11 [ 37.243714] Bluetooth: L2CAP socket layer initialized [ 37.306820] Bluetooth: RFCOMM socket layer initialized [ 37.308129] Bluetooth: RFCOMM TTY layer initialized [ 37.309361] Bluetooth: RFCOMM ver 1.10 [ 37.544928] lp: driver loaded but no devices found [ 37.565781] ppdev: user-space parallel port driver [ 56.811060] [drm] Initialized drm 1.1.0 20060810 [ 56.823231] [drm] Initialized radeon 1.29.0 20080528 on minor 0 [ 58.397095] agpgart-via 0000:00:00.0: AGP 2.0 bridge [ 58.397130] agpgart-via 0000:00:00.0: putting AGP V2 device into 4x mode [ 58.397186] radeonfb 0000:01:00.0: putting AGP V2 device into 4x mode [ 58.768210] [drm] Setting GART location based on new memory map [ 58.768327] [drm] Loading R200 Microcode [ 58.768333] platform radeon_cp.0: firmware: requesting radeon/R200_cp.bin [ 58.819172] radeon_cp: Failed to load firmware "radeon/R200_cp.bin" [ 58.819182] [drm:radeon_do_init_cp] *ERROR* Failed to load firmware! ** Loaded modules: Module Size Used by radeon 102684 0 drm 133260 1 radeon binfmt_misc 7168 1 ppdev 6224 0 parport_pc 22020 0 lp 7872 0 parport 30868 3 ppdev,parport_pc,lp rfcomm 29636 2 l2cap 17072 9 rfcomm bluetooth 46052 4 rfcomm,l2cap ipv6 232468 8 dm_crypt 11156 0 dm_mod 49048 1 dm_crypt fuse 48352 1 snd_via82xx 20628 1 gameport 10120 1 snd_via82xx snd_ac97_codec 91260 1 snd_via82xx ac97_bus 1444 1 snd_ac97_codec snd_pcm_oss 31708 0 snd_mixer_oss 12000 1 snd_pcm_oss snd_pcm 62704 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss snd_page_alloc 8036 2 snd_via82xx,snd_pcm snd_mpu401_uart 6180 1 snd_via82xx snd_seq_dummy 2368 0 snd_seq_oss 24756 0 snd_seq_midi 5448 0 snd_rawmidi 18544 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 6072 2 snd_seq_oss,snd_seq_midi snd_seq 42120 7 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event snd_timer 17808 2 snd_pcm,snd_seq snd_seq_device 6108 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq pcspkr 2092 0 snd 48420 14 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device i2c_viapro 6692 0 radeonfb 56052 1 soundcore 6204 1 snd fb_ddc 1820 1 radeonfb via_ircc 15704 0 usblp 10384 0 i2c_algo_bit 4888 1 radeonfb irda 95336 1 via_ircc i2c_core 20828 5 drm,i2c_viapro,radeonfb,fb_ddc,i2c_algo_bit crc_ccitt 1800 1 irda evdev 8160 3 shpchp 26836 0 pci_hotplug 24464 1 shpchp via_agp 7548 1 agpgart 30624 2 drm,via_agp button 5672 0 ext3 107180 8 jbd 42500 1 ext3 mbcache 7180 1 ext3 ide_cd_mod 25532 0 cdrom 29804 1 ide_cd_mod ide_gd_mod 18904 10 ide_pci_generic 3408 0 ata_generic 4316 0 libata 148892 1 ata_generic scsi_mod 132076 1 libata usbhid 29132 0 hid 34260 1 usbhid floppy 46852 0 via82cxxx 5884 9 uhci_hcd 19392 0 ide_core 91820 4 ide_cd_mod,ide_gd_mod,ide_pci_generic,via82cxxx ehci_hcd 29836 0 usbcore 124872 5 usblp,usbhid,uhci_hcd,ehci_hcd 8139cp 17356 0 8139too 21164 0 mii 4648 2 8139cp,8139too thermal 15092 0 processor 39540 2 thermal fan 4104 0 thermal_sys 10272 3 thermal,processor,fan ** PCI devices: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge [1106:3189] Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 8 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M] Capabilities: <access denied> Kernel driver in use: agpgart-via 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8235 PCI Bridge [1106:b168] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: e0000000-e1ffffff Prefetchable memory behind bridge: d8000000-dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:0d.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at d000 [size=256] Region 1: Memory at e3000000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 40000000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: 8139too 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at d400 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at d800 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 21 Region 4: I/O ports at dc00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 82) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin D routed to IRQ 21 Region 0: Memory at e3001000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177] Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology GA-7VAX Mainboard [1458:5002] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 20 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at e000 [size=16] Capabilities: <access denied> Kernel driver in use: VIA_IDE 00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 50) Subsystem: Giga-byte Technology GA-7VAX Onboard Audio (Realtek ALC650) [1458:a002] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 22 Region 0: I/O ports at e400 [size=256] Capabilities: <access denied> Kernel driver in use: VIA 82xx Audio 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon RV250 If [Radeon 9000] [1002:4966] (rev 01) (prog-if 00 [VGA controller]) Subsystem: Hightech Information System Ltd. RV250 If [Excalibur Radeon 9000] [17af:2006] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M] Region 1: I/O ports at c000 [size=256] Region 2: Memory at e1000000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at e0000000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: radeonfb 01:00.1 Display controller [0380]: ATI Technologies Inc Radeon RV250 [Radeon 9000] (Secondary) [1002:496e] (rev 01) Subsystem: Hightech Information System Ltd. Device [17af:2007] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min), Cache Line Size: 32 bytes Region 0: Memory at dc000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at e1010000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> -- System Information: Debian Release: squeeze/sid APT prefers unstable APT policy: (500, 'unstable'), (1, 'experimental') Architecture: i386 (i686) Kernel: Linux 2.6.29-1-686 (SMP w/1 CPU core) Locale: LANG=polish, LC_CTYPE=pl_PL.UTF-8 (charmap=UTF-8) (ignored: LC_ALL set to pl_PL.UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.29-1-686 depends on: ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy ii initramfs-tools [linux-initra 0.93.1 tools for generating an initramfs ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.29-1-686 recommends: ii libc6-i686 2.9-6 GNU C Library: Shared libraries [i Versions of packages linux-image-2.6.29-1-686 suggests: ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v ii linux-doc-2.6.29 2.6.29-1 Linux kernel specific documentatio -- debconf-show failed -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected]
