Package: linux-2.6 Version: 2.6.32-28 Severity: normal Hi.
Trying to connect to a wifi network (in France) which uses Channel 13 fails with a USB network card which requires zd1211. It appears that after stock install, I have : # cat /sys/module/cfg80211/parameters/ieee80211_regdom 00 I need to set /etc/modprobe.d/cfg80211.conf with : options cfg80211 ieee80211_regdom=EU to make it work. I guess there's a bug here, which may be related to the lack of debconf question for setting such parameters or similar configuration mechanism prompting the user, or to a buggy automagic detection of the regdom. In any case, it's far from obvious for non-expert user why some AP would be seen (channels OK for US) and some not (for instance on channels 12 and 13). Hope this helps. Best regards, -- Package-specific info: ** Version: Linux version 2.6.32-5-686 (Debian 2.6.32-28) (b...@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Nov 25 18:43:34 UTC 2010 ** Command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/josephine-root ro quiet ** Not tainted ** Kernel log: [ 5.116781] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7 [ 5.135257] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8 [ 5.193154] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 5.339644] intel_rng: FWH not detected [ 5.383340] [drm] Initialized drm 1.1.0 20060810 [ 5.424102] cfg80211: Using static regulatory domain info [ 5.424105] cfg80211: Regulatory domain: US [ 5.424107] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 5.424111] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 5.424114] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424118] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424121] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424125] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424128] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 5.424402] cfg80211: Calling CRDA for country: US [ 5.748489] i915 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 5.748496] i915 0000:00:02.0: setting latency timer to 64 [ 5.767564] [drm] set up 0M of stolen space [ 5.885198] [drm] initialized overlay support [ 6.218734] yenta_cardbus 0000:01:01.0: CardBus bridge found [1028:0163] [ 6.218749] yenta_cardbus 0000:01:01.0: Using CSCINT to route CSC interrupts to PCI [ 6.218752] yenta_cardbus 0000:01:01.0: Routing CardBus interrupts to PCI [ 6.218758] yenta_cardbus 0000:01:01.0: TI: mfunc 0x012c1222, devctl 0x64 [ 6.649130] usb 1-3: reset high speed USB device using ehci_hcd and address 2 [ 6.802911] yenta_cardbus 0000:01:01.0: ISA IRQ mask 0x0458, PCI irq 11 [ 6.802916] yenta_cardbus 0000:01:01.0: Socket status: 30000086 [ 6.802922] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05 [ 6.802932] yenta_cardbus 0000:01:01.0: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff [ 6.802937] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xe000-0xefff: clean. [ 6.803510] yenta_cardbus 0000:01:01.0: pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff [ 6.803514] yenta_cardbus 0000:01:01.0: pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff [ 6.909641] Console: switching to colour frame buffer device 175x65 [ 6.920550] fb0: inteldrmfb frame buffer device [ 6.920552] registered panic notifier [ 6.920581] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 7.224453] phy0: Selected rate control algorithm 'minstrel' [ 7.225205] zd1211rw 1-3:1.0: phy0 [ 7.225229] usbcore: registered new interface driver zd1211rw [ 7.389083] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean. [ 7.389899] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean. [ 7.390252] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean. [ 7.390303] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean. [ 7.390742] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean. [ 7.728139] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5 [ 7.728176] Intel ICH 0000:00:1f.5: setting latency timer to 64 [ 8.556038] intel8x0_measure_ac97_clock: measured 55243 usecs (2662 samples) [ 8.556042] intel8x0: clocking to 48000 [ 8.557234] Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5 [ 8.557256] Intel ICH Modem 0000:00:1f.6: setting latency timer to 64 [ 8.660071] MC'97 1 converters and GPIO not ready (0xff00) [ 9.758441] EXT3 FS on dm-0, internal journal [ 9.936827] loop: module loaded [ 10.580930] Adding 2170872k swap on /dev/mapper/josephine-swap_1. Priority:-1 extents:1 across:2170872k [ 11.262981] kjournald starting. Commit interval 5 seconds [ 11.263316] EXT3 FS on dm-2, internal journal [ 11.263322] EXT3-fs: mounted filesystem with ordered data mode. [ 12.472799] fuse init (API version 7.13) [ 15.174506] usb 1-3: firmware: requesting zd1211/zd1211_ub [ 15.318326] usb 1-3: firmware: requesting zd1211/zd1211_uphr [ 15.586222] zd1211rw 1-3:1.0: firmware version 4605 [ 15.626230] zd1211rw 1-3:1.0: zd1211 chip 0586:3401 v4330 high 00-13-49 AL2230_RF pa0 g---- [ 15.628746] cfg80211: Calling CRDA for country: DE [ 15.650969] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 15.669901] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 17.725435] Bluetooth: Core ver 2.15 [ 17.725498] NET: Registered protocol family 31 [ 17.725500] Bluetooth: HCI device and connection manager initialized [ 17.725504] Bluetooth: HCI socket layer initialized [ 17.778037] Bluetooth: L2CAP ver 2.14 [ 17.778040] Bluetooth: L2CAP socket layer initialized [ 17.894094] Bluetooth: RFCOMM TTY layer initialized [ 17.894100] Bluetooth: RFCOMM socket layer initialized [ 17.894103] Bluetooth: RFCOMM ver 1.11 [ 17.946275] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.946279] Bluetooth: BNEP filters: protocol multicast [ 18.124701] Bridge firewalling registered [ 18.318460] Bluetooth: SCO (Voice Link) ver 0.6 [ 18.318463] Bluetooth: SCO socket layer initialized [ 19.440908] lp0: using parport0 (interrupt-driven). [ 19.705514] ppdev: user-space parallel port driver [ 62.517918] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 1) [ 62.716071] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 2) [ 62.916040] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 3) [ 63.118030] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 timed out [ 68.439823] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 1) [ 68.636059] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 2) [ 68.836098] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 3) [ 69.036561] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a timed out [ 74.383936] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 1) [ 74.580122] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 2) [ 74.780052] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 3) [ 74.980077] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a timed out [ 80.296965] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 (try 1) [ 80.496057] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 (try 2) [ 80.696056] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 (try 3) [ 80.896053] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 timed out [ 86.226972] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 1) [ 86.424051] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 2) [ 86.624036] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 3) [ 86.824060] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 timed out ** Model information not available ** Loaded modules: Module Size Used by acpi_cpufreq 4943 0 cpufreq_powersave 602 0 cpufreq_userspace 1480 0 cpufreq_conservative 4018 0 cpufreq_stats 1940 0 ppdev 4058 0 lp 5570 0 sco 5857 2 bridge 33019 0 stp 996 1 bridge bnep 7444 2 rfcomm 25171 0 l2cap 21705 6 bnep,rfcomm crc16 1027 1 l2cap bluetooth 36319 6 sco,bnep,rfcomm,l2cap binfmt_misc 4907 1 fuse 43829 1 ext2 46293 1 firewire_sbp2 9647 0 loop 9765 0 snd_intel8x0m 8100 0 snd_intel8x0 19555 1 snd_ac97_codec 79148 2 snd_intel8x0m,snd_intel8x0 ac97_bus 710 1 snd_ac97_codec snd_pcm_oss 28671 0 snd_mixer_oss 10461 1 snd_pcm_oss snd_pcm 47226 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss arc4 974 2 ecb 1405 2 snd_seq_midi 3576 0 snd_rawmidi 12513 1 snd_seq_midi pcmcia 16194 0 snd_seq_midi_event 3684 1 snd_seq_midi snd_seq 35463 2 snd_seq_midi,snd_seq_midi_event snd_timer 12258 2 snd_pcm,snd_seq yenta_socket 16403 1 rsrc_nonstatic 7057 1 yenta_socket zd1211rw 32550 0 snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 123574 1 zd1211rw i915 222064 2 pcmcia_core 20450 3 pcmcia,yenta_socket,rsrc_nonstatic drm_kms_helper 18301 1 i915 snd 34375 12 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 87661 2 zd1211rw,mac80211 drm 112088 3 i915,drm_kms_helper i2c_algo_bit 3497 1 i915 shpchp 21220 0 soundcore 3450 1 snd snd_page_alloc 5045 3 snd_intel8x0m,snd_intel8x0,snd_pcm joydev 6739 0 parport_pc 15799 1 dell_laptop 1533 0 rfkill 10264 5 bluetooth,cfg80211,dell_laptop rng_core 2178 0 parport 22554 3 ppdev,lp,parport_pc i2c_core 12696 4 i915,drm_kms_helper,drm,i2c_algo_bit psmouse 44657 0 pcspkr 1207 0 pci_hotplug 18065 1 shpchp dcdbas 3892 1 dell_laptop processor 26327 2 acpi_cpufreq button 3598 1 i915 video 14605 1 i915 battery 3782 0 output 1204 1 video ac 1640 0 evdev 5609 14 serio_raw 2916 0 ext3 94204 2 jbd 32169 1 ext3 mbcache 3762 2 ext2,ext3 dm_mod 46094 9 sd_mod 25969 3 crc_t10dif 1012 1 sd_mod ata_generic 2047 0 uhci_hcd 16057 0 ata_piix 17736 2 thermal 9206 0 firewire_ohci 16509 0 libata 115745 2 ata_generic,ata_piix ehci_hcd 27851 0 thermal_sys 9378 3 processor,video,thermal e100 22317 0 mii 2714 1 e100 firewire_core 31187 2 firewire_sbp2,firewire_ohci crc_itu_t 1035 1 firewire_core scsi_mod 101421 3 firewire_sbp2,sd_mod,libata usbcore 98453 4 zd1211rw,uhci_hcd,ehci_hcd nls_base 4541 1 usbcore ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3580] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at <unassigned> (32-bit, prefetchable) Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:00.1 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3584] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.3 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3585] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:02.0 VGA compatible controller [0300]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02) (prog-if 00 [VGA controller]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at faf80000 (32-bit, non-prefetchable) [size=512K] Region 2: I/O ports at c000 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:02.1 Display controller [0380]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at faf00000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 0: Memory at faeffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 81) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=05, sec-latency=32 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fc000000-fdffffff Prefetchable memory behind bridge: 40000000-43ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Region 5: Memory at 44000000 (32-bit, non-prefetchable) [size=1K] Kernel driver in use: ata_piix 00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at d800 [size=256] Region 1: I/O ports at dc40 [size=64] Region 2: Memory at faeff800 (32-bit, non-prefetchable) [size=512] Region 3: Memory at faeff400 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: Intel ICH 00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 01) (prog-if 00 [Generic]) Subsystem: Conexant Systems, Inc. D480 MDC V.9x Modem [14f1:5422] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at d400 [size=256] Region 1: I/O ports at d080 [size=128] Capabilities: <access denied> Kernel driver in use: Intel ICH Modem 01:01.0 CardBus bridge [0607]: Texas Instruments PCI4510 PC card Cardbus Controller [104c:ac44] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=01, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 40000000-43fff000 (prefetchable) Memory window 1: 48000000-4bfff000 I/O window 0: 0000e000-0000e0ff I/O window 1: 0000e400-0000e4ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus 01:01.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4510 IEEE-1394 Controller [104c:8029] (prog-if 10 [OHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at fcfff800 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at fcff8000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: firewire_ohci 01:08.0 Ethernet controller [0200]: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller [8086:103d] (rev 81) Subsystem: Dell Latitude D500 [1028:2002] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fcffe000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at ecc0 [size=64] Capabilities: <access denied> Kernel driver in use: e100 ** USB devices: Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0586:3401 ZyXEL Communications Corp. ZyAIR G-220 802.11bg Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: squeeze/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core) Locale: LANG=fr_FR.utf8, LC_CTYPE=fr_FR.utf8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-686 depends on: ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs ii linux-base 2.6.32-28 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-686 recommends: ii firmware-linux-free 2.6.32-28 Binary firmware for various driver ii libc6-i686 2.11.2-7 Embedded GNU C Library: Shared lib Versions of packages linux-image-2.6.32-5-686 suggests: ii grub 0.97-63 GRand Unified Bootloader (dummy pa pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) ii firmware-ipw2x00 0.27 Binary firmware for Intel Pro Wire pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) ii firmware-linux 0.27 Binary firmware for various driver ii firmware-linux-nonfree 0.27 Binary firmware for various driver pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686: * linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686: -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20101205173015.3375.1267.report...@josephine