On Thu, 12 Mar 2009 13:59:24 -0700 "Brandeburg, Jesse" <jesse.brandeb...@intel.com> wrote:
> re-added the list for tracking... > > I think I see the issue, you have more than 4GB ram, and it appears that > your system doesn't handle dual address cycles correctly, or our adapter > doesn't work quite right for some reason. > > Force the OS to never allow addresses > 4GB to our hardware using this > patch: > https://sourceforge.net/tracker2/download.php?group_id=42302&atid=447449&file_id=283326&aid=2007017 > > its the e1000_disable_dac.patch file. i prefer more "optional" ways of disabling features so i wrote the following (probably horrible, but functional) patch: diff -urpd e1000-8.0.6/src/e1000_main.c e1000-8.0.6.new/src/e1000_main.c --- e1000-8.0.6/src/e1000_main.c 2008-07-30 03:46:25.000000000 +0000 +++ e1000-8.0.6.new/src/e1000_main.c 2009-02-17 06:37:33.000000000 +0000 @@ -65,7 +65,7 @@ static char e1000_driver_string[] = "Int #define DRV_HW_PERF -#define DRV_VERSION "8.0.6" DRV_NAPI DRV_DEBUG DRV_HW_PERF +#define DRV_VERSION "8.0.6-64bit_DMA_param" DRV_NAPI DRV_DEBUG DRV_HW_PERF const char e1000_driver_version[] = DRV_VERSION; static const char e1000_copyright[] = "Copyright (c) 1999-2008 Intel Corporation."; @@ -227,6 +227,9 @@ module_param(copybreak, uint, 0644); MODULE_PARM_DESC(copybreak, "Maximum size of packet that is copied to a new buffer on receive"); +static int ignore_64bit_dma = 0; +module_param(ignore_64bit_dma, int, 0644); +MODULE_PARM_DESC(ignore_64bit_dma, "Ignore 64-bit DMA (DAC) capability"); #ifdef HAVE_PCI_ERS static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev, @@ -723,7 +726,8 @@ static int __devinit e1000_probe(struct if ((err = pci_enable_device(pdev))) return err; - if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) && + if (!ignore_64bit_dma && + !(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) && !(err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK))) { pci_using_dac = 1; } else { i too was plagued by the "Detected Tx Unit Hang" on my Gigabyte GA-MA78G-DS3H with an Intel PRO/1000 MT installed (see lspci output at the end of this email) and i heeded all the related bug reports, with none of them working, until i came across the one that talked about > 4 GB of RAM (which i have 8 GB in this affected computer). the e1000_disable_dac.patch worked for me. i ran across a bug report response that said the e1000 driver would not be patched to accommodate this buggy hardware (because it's the motherboard's fault, not the e1000 driver or hardware), so i wrote the included patch to help encourage Intel to at least provide an in-driver user-configurable work-around (so i don't have to eternally patch the e1000 driver to disable 64-bit DAC). thanks for the e1000 driver and the great support. corey -- undefi...@pobox.com 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] Subsystem: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 Region 3: Memory at <ignored> (64-bit, non-prefetchable) Capabilities: [c4] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 3.00 Link Frequency 0: 1.0GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [54] HyperTransport: UnitID Clumping Capabilities: [40] HyperTransport: Retry Mode Capabilities: [9c] HyperTransport: #1a Capabilities: [f8] HyperTransport: #1c 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fdd00000-fdefffff Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602] Kernel modules: shpchp 00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) [1022:9609] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # a, PowerLimit 25.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 4151 Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device [1022:9600] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0]) Subsystem: Giga-byte Technology Device [1458:b002] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] SATA HBA <?> Kernel driver in use: ahci Kernel modules: ahci 00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 19 Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3a) Subsystem: Giga-byte Technology Device [1458:4385] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR+ <PERR+ INTx- Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: piix4_smbus Kernel modules: i2c-piix4 00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology Device [1458:5002] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at fa00 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Kernel driver in use: ATIIXP_IDE Kernel modules: ata_generic, ide-pci-generic, atiixp 00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=03, subordinate=03, sec-latency=64 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: fdb00000-fdbfffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD 3200 Graphics [1002:9610] (prog-if 00 [VGA controller]) Subsystem: Giga-byte Technology Device [1458:d000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 5 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at ee00 [size=256] Region 2: Memory at fdee0000 (32-bit, non-prefetchable) [size=64K] Region 5: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 01:05.1 Audio device [0403]: ATI Technologies Inc RS780 Azalia controller [1002:960f] Subsystem: ATI Technologies Inc RS780 Azalia controller [1002:960f] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 7 Region 0: Memory at fdefc000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel modules: snd-hda-intel 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02) Subsystem: Giga-byte Technology Device [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 1278 Region 0: I/O ports at de00 [size=256] Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fdfe0000 (64-bit, prefetchable) [size=64K] [virtual] Expansion ROM at fdf00000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0300c Data: 4179 Capabilities: [70] Express (v1) Endpoint, MSI 01 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM+ Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2 Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 78-56-34-12-78-56-34-12 Kernel driver in use: r8169 Kernel modules: r8169 03:07.0 Ethernet controller [0200]: Intel Corporation 82540EM Gigabit Ethernet Controller [8086:100e] (rev 02) Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter [8086:002e] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 21 Region 0: Memory at fdcc0000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fdca0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at cf00 [size=64] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: e1000 Kernel modules: e1000 03:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology Device [1458:1000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 22 Region 0: Memory at fdcff000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at fdcf8000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ohci1394 Kernel modules: ohci1394 ------------------------------------------------------------------------------ Apps built with the Adobe(R) Flex(R) framework and Flex Builder(TM) are powering Web 2.0 with engaging, cross-platform capabilities. Quickly and easily build your RIAs with Flex Builder, the Eclipse(TM)based development software that enables intelligent coding and step-through debugging. Download the free 60 day trial. http://p.sf.net/sfu/www-adobe-com _______________________________________________ E1000-devel mailing list E1000-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/e1000-devel
