Thanks to VE3KI who caught a typing error in the second line of commands of the original Triple Macro. The following is a corrected version.
73, Rich - K1HTV = = = After seeing the note about creating a macro to toggle between two power levels on the K3, I thought I would try writing a macro for a triple toggle. With this macro the K3 power output can be toggled between 10W, 50W and 100W using the PF2-HOLD key. If you prefer to TAP instead of HOLD, use one of the M1-4 keys and change the SWH47 to the appropriate "SWTnn" number. Refer to the K3 Macro tutorial. This is being written not only for the K3 users who already know how to write macros, but for those K3 users who have never done so and want to give it a try. So please excuse the extra steps which must be performed that you already know how to do. Assuming that you already have the K3 Utility installed on your computer, turn on your K3. Start the K3 Utility and confirm that your K3 is communicating with your computer. Click the "Test Communications" tab. Click "Port Test Communications". If successful you will get a box indicating so. Click the "Command Tester/K3 Macros" tab. Click "Edit Macro" Use the information below to populate the "Macro Label" boxes and the Macro Commands" boxes for the macro number that you will be using. At K1HTV I used the K3's 5, 6 and 7 macros for the triple power toggle. If you use other ones, change the SWT29, SWT33 and SWT27 to the appropriate numbers for the macro numbers you want to use. You can type in the info below, but you will probably find it easier to simple cut and paste the commands (the ones with the semicolons between) from this document into the K3 Utility macro boxes being used. Macro# Label (10W) (Macro) (6) (PF2H) (Menu) 5 10W PC010;MN110;SWT29;SWH47;SWT14; Label (50W) (Macro) (7) (PF2H) (Menu) 6 50W PC050;MN110;SWT33;SWH47;SWT14; Label (100W) (Macro) (5) (PF2H) (Menu) 7 100W PC100;MN110;SWT27;SWH47;SWT14; After you have filled in the "Macro Label" and :Macro Commands" boxes for Macro 5 (10W), Macro 6 (50W) and Macro 7 (100W) click on "Write Macros 1-8 to K3". Next, at the K3: Hold the MENU key. Rotate the VFO-B dial until "MACRO" appears. Tap the "5" on the keypad so the screen reads "MACRO 5". Hold the PF2 key until "PF2 SET" appears. Tap the MENU key. Hold the MENU key again until MACRO appears. Tap "6" on the keypad so the screen reads "MACRO 6". Hold the PF2 key until "PF2 SET" appears. Tap the MENU key. Tap "7" on the keypad so the screen reads "MACRO 7". Hold the PF2 key until "PF2 SET" appears. Tap the MENU key. Test by holding the PF2 key until either 10W, 50W or 100W appears briefly on the LCD screen. It should toggle between the three power levels each time you HOLD the PF2 key. *** NOTE*** When writing lines of multi-line toggling macros, make sure the number for the macro number following the MN110; is the macro number for the following line or the toggle feature will not work. Hope you find this info useful. 73, Rich - K1HTV ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html