I forgot to say that I was using: kernel 2.6.20.1 (I tried it also with 2.6.20.3) ivtv-0.10.1 lirc-cvs and lirc-0.8.x and patched lirc from mark's page.
M. 2007/3/19, Ma Begaj <[EMAIL PROTECTED]>: > Hi to all, > > I had a lot of problems to get my pvr150-remote working. lirc_i2c was not > able to recognize it. > last week I got it somehow to work with lirc from cvs. > > Yesterday I put my computer to standby (suspend to mem). lirc_i2c was not > able to recognize the remote after waking up. Reboot and recompiling lirc > and ivtv did not help at all. I asked on this page ( > http://www.blushingpenguin.com/mark/blog/?p=24) for some > advice and Mark told me to try to contact Hans on ivtv-devel, so here I am. > > he told me to run "--reset-ir", but I always got this error when I run it: > ioctl VIDIOC_INT_RESET failed: Invalid argument > > > Now, situation is same as a few days ago. Remote is not recognized and I am > trying all the combinations to get it work: ivtv newi2c=1, newi2c=0, old > lirc, new lirc, old kernel, new kernel ... and I have no idea what to do > now. Mark suggested me to try this "you can power off the machine, > disconnect the power cord, wait for a minute or so, then power it up again", > but it did not help. I also tried his lirc_pvr150 module, but also no > success. > > I checked my yesterday's syslog and found this line when the remote was > working: > lirc_i2c: chip found @ 0×71 (Hauppauge IR (PVR150)) > > but this is my today's dmesg after loading ivtv and lirc_pvr150 / lirc_i2c: > > vtv: ==================== START INIT IVTV ==================== > ivtv: version 0.10.1 (tagged release) loading > ivtv: Linux version: 2.6.20.1 SMP mod_unload K8 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge card (cx23416 based) > ACPI: PCI Interrupt 0000:03:07.0[A] -> Link [APC2] -> GSI 17 (level, low) > -> IRQ 22 > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > ivtv0: Encoder revision: 0×02060039 > tveeprom 5-0050: Hauppauge model 26134, rev F1B3, serial# 10233063 > tveeprom 5-0050: tuner model is TCL M2523_3DB_E (idx 113, type 55) > tveeprom 5-0050: TV standards PAL(B/G) PAL(D/D1/K) (eeprom 0×44) > tveeprom 5-0050: audio processor is CX25842 (idx 36) > tveeprom 5-0050: decoder processor is CX25842 (idx 29) > tveeprom 5-0050: has no radio, has IR receiver, has IR transmitter > ivtv0: Autodetected Hauppauge WinTV PVR-150 > tuner 5-0061: chip found @ 0xc2 (ivtv i2c driver #0) > cx25840 5-0044: cx25842-23 found @ 0×88 (ivtv i2c driver #0) > cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes) > wm8775 5-001b: chip found @ 0×36 (ivtv i2c driver #0) > ivtv0: Registered device video0 for encoder MPEG (4 MB) > ivtv0: Registered device video32 for encoder YUV (2 MB) > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > tuner 5-0061: type set to 55 (TCL 2002MB) > ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== END INIT IVTV ==================== > lirc_dev: IR Remote Control driver registered, at major 61 > lirc_pvr150: probe 0×70 @ ivtv i2c driver #0: no > lirc_pvr150: probe 0×71 @ ivtv i2c driver #0: no > lirc_pvr150: ivtv i2c driver #0: no devices found > > > > Any ideas? > > Thanks a lot. > > M. > > -- Glauben heißt nicht wissen wollen, was wahr ist ... Nietzsche _______________________________________________ ivtv-devel mailing list ivtv-devel@ivtvdriver.org http://ivtvdriver.org/mailman/listinfo/ivtv-devel
