I will try to be as thorough as possible to expediate this. Got a pair
of PVR-150 cards today to replace my BT878 cards. Tossed em into my
mythtv backend and dove into HOWTOs and FAQs at various websites. So
far here is where I am.
Removed ivtv related modules from Mandriva kernel.
Downloaded ivtv.
Compiled ivtv.
Extracted the firmware from CD.
Symlinked the proper firmware file.
Depmod -a
-modprobe.conf-
alias char-major-81 -0 ivtv
alias char-major-81 -1 ivtv
options ivtv tuner=-1,-1
I think i have that all setup properly. So after a modprobe tveeprom, i
issue the crucial modprobe ivtv and here is the output.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3j) loading
ivtv: Linux version: 2.6.11-6mdk 686 gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
PCI: Found IRQ 10 for device 0000:02:0b.0
PCI: Sharing IRQ 10 with 0000:00:1f.4
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x1a30 vendor: 0x8086
ivtv: i2c attach [client=tveeprom,ok]
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 7969385
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3410D (type = 5)
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
0x008d2598, Revision 0xe0c397a0
ivtv: NTSC tuner detected
ivtv: Radio detected
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
cx25840: Ignoring new-style parameters in presence of obsolete ones
cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded.
cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa
cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6
ivtv: i2c attach [client=cx25840[0],ok]
wm8775: Ignoring new-style parameters in presence of obsolete ones
wm8775: Setting register ADCFMT (7) to 1, R11.0..1, old value 02
wm8775: Setting register ADCMS (8) to 1, R12.8..8, old value 00
wm8775: Setting register DCY (24) to 8, R18.4..7, old value 03
wm8775: Setting register NGAT (27) to 1, R19.0..0, old value 00
wm8775: Setting register LRBOTH (30) to 1, R21.8..8, old value 00
wm8775: Setting register AMX (33) to 15, R21.0..3, old value 01
wm8775: Updating register 0 (R23), config: 2e01 active: 2e00.
wm8775: Skipping register 1 (R7), config: 0e00 active: 0e00.
wm8775: Updating register 2 (R11), config: 1622 active: 1621.
wm8775: Updating register 3 (R12), config: 1802 active: 1902.
wm8775: Skipping register 4 (R13), config: 1a00 active: 1a00.
wm8775: Skipping register 5 (R14), config: 1ccf active: 1ccf.
wm8775: Skipping register 6 (R15), config: 1ecf active: 1ecf.
wm8775: Skipping register 7 (R16), config: 207b active: 207b.
wm8775: Skipping register 8 (R17), config: 2200 active: 2200.
wm8775: Updating register 9 (R18), config: 2432 active: 2482.
wm8775: Updating register 10 (R19), config: 2600 active: 2601.
wm8775: Skipping register 11 (R20), config: 2826 active: 2826.
wm8775: Updating register 12 (R21), config: 2a01 active: 2b0f.
ivtv: i2c attach [client=wm8775[0],ok]
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes
total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 47
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 150, card #0
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ivtv: ivtv_enc_thread: pid = 6781, itv = 0xe0c397a0
PCI: Found IRQ 9 for device 0000:02:0c.0
PCI: Sharing IRQ 9 with 0000:00:1f.3
PCI: Sharing IRQ 9 with 0000:00:1f.5
PCI: Sharing IRQ 9 with 0000:02:0e.0
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x1a30 vendor: 0x8086
ivtv: i2c attach [client=tveeprom,ok]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv: i2c attach [client=(tuner unset),ok]
cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded.
cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa
cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6
ivtv: i2c attach [client=cx25840[1],ok]
wm8775: Setting register ADCFMT (7) to 1, R11.0..1, old value 02
wm8775: Setting register ADCMS (8) to 1, R12.8..8, old value 00
wm8775: Setting register DCY (24) to 8, R18.4..7, old value 03
wm8775: Setting register NGAT (27) to 1, R19.0..0, old value 00
wm8775: Setting register LRBOTH (30) to 1, R21.8..8, old value 00
wm8775: Setting register AMX (33) to 15, R21.0..3, old value 01
wm8775: Updating register 0 (R23), config: 2e01 active: 2e00.
wm8775: Skipping register 1 (R7), config: 0e00 active: 0e00.
wm8775: Updating register 2 (R11), config: 1622 active: 1621.
wm8775: Updating register 3 (R12), config: 1802 active: 1902.
wm8775: Skipping register 4 (R13), config: 1a00 active: 1a00.
wm8775: Skipping register 5 (R14), config: 1ccf active: 1ccf.
wm8775: Skipping register 6 (R15), config: 1ecf active: 1ecf.
wm8775: Skipping register 7 (R16), config: 207b active: 207b.
wm8775: Skipping register 8 (R17), config: 2200 active: 2200.
wm8775: Updating register 9 (R18), config: 2432 active: 2482.
wm8775: Updating register 10 (R19), config: 2600 active: 2601.
wm8775: Skipping register 11 (R20), config: 2826 active: 2826.
wm8775: Updating register 12 (R21), config: 2a01 active: 2b0f.
ivtv: i2c attach [client=wm8775[1],ok]
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8402116
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3410D (type = 5)
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
0x008d2598, Revision 0xe0c4da60
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes
total
ivtv: Registered v4l2 device, streamtype 0 minor 1
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 33
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 225
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 25
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 65
ivtv: Setting Tuner 47
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #1
ivtv: ivtv_enc_thread: pid = 6951, itv = 0xe0c4da60
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================
That log looks good to me. So I tried cat /dev/video0 to a .mpg and
playing it with mplayer. I got static fading in and out. Tried it
again on other tuner. Same thing, fading in and out of a black screen
and static. I also tried using ptune_ui to manually tune it to a
channel and again same thing. I hope this is a common problem and I am
missing something simple.
Here is lspci output
[EMAIL PROTECTED] ~]# lspci -vvv
00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset
Host Bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [0104]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW-
Rate=x4
00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP
Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc900000-fe9fffff
Prefetchable memory behind bridge: e0600000-e46fffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 12) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: e4700000-f47fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 12)
(prog-if 80 [Master])
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev
12) (prog-if 00 [UHCI])
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 3
Region 4: I/O ports at ef40 [size=32]
00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 12)
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 9
Region 4: I/O ports at efa0 [size=16]
00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev
12) (prog-if 00 [UHCI])
Subsystem: Intel Corporation: Unknown device 4856
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 4: I/O ports at ef80 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97
Audio (rev 12)
Subsystem: Intel Corporation: Unknown device 6876
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 9
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ef00 [size=64]
01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta/Vanta
LT] (rev 15) (prog-if 00 [VGA])
Subsystem: VISIONTEK: Unknown device 0004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e2000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at fe9f0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit-
FW- Rate=x4
02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM
Ethernet Controller (rev 03)
Subsystem: Intel Corporation EtherExpress PRO/100 VE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at df00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs: Unknown device 8032
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at df80 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0a.1 Input device controller: Creative Labs SB Live! MIDI/Game Port
(rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at dff0 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0b.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 8801
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), cache line size 04
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0c.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 8801
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), cache line size 04
Interrupt: pin A routed to IRQ 9
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0e.0 Ethernet controller: Linksys NC100 Network Everywhere Fast
Ethernet 10/100 (rev 11)
Subsystem: Linksys: Unknown device 0574
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min, 63750ns max), cache line size 04
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at feafec00 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
TIA
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
_______________________________________________
ivtv-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
