Hello
I,m using Bering Leaf from 2000. First Bering Leaf 1.0, from 2003 Bering
Leaf 2003 and now Bering-uClibc 3.1
My Info:
------- start of info -----------
firewall# uname -a
Linux firewall 2.4.34 #1 Tue Jan 23 20:12:21 CET 2007 i686 unknown
firewall# ip addr show
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,NOTRAILERS,UP> mtu 1500 qdisc pfifo_fast
qlen 1000
link/ether 00:0a:cd:00:91:71 brd ff:ff:ff:ff:ff:ff
inet 212.76.51.79/22 brd 212.76.51.255 scope global eth0
4: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 00:0a:cd:00:99:f9 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.1/24 brd 192.168.0.255 scope global eth1
firewall# ip route show
192.168.0.0/24 dev eth1 proto kernel scope link src 192.168.0.1
212.76.48.0/22 dev eth0 proto kernel scope link src 212.76.51.79
default via 212.76.51.254 dev eth0
firewall# lsmod
Module Size Used by Not tainted
lp 4880 1
parport_pc 14228 1
parport 10880 1 [lp parport_pc]
softdog 1392 1
ipt_ipp2p 5908 0
ipt_state 272 18
ipt_helper 400 0 (unused)
ipt_conntrack 692 0
ipt_REDIRECT 480 0 (unused)
ipt_MASQUERADE 1024 1
ip_nat_irc 1704 0 (unused)
ip_nat_ftp 2152 0 (unused)
iptable_nat 14388 3 [ipt_REDIRECT ipt_MASQUERADE ip_nat_irc
ip_nat_ftp]
ip_conntrack_irc 2484 1
ip_conntrack_ftp 3132 1
ip_conntrack 16548 2 [ipt_state ipt_helper ipt_conntrack
ipt_REDIRECT ipt_MASQUERADE ip_nat_irc ip_nat_ftp iptable_nat
ip_conntrack_irc ip_conntrack_ftp]
8139too 11944 2
mii 1820 0 [8139too]
crc32 2620 0 [8139too]
vfat 8492 0 (unused)
isofs 15732 0
ide-detect 132 0 (unused)
ide-cd 26748 0
ide-disk 11372 0
ide-core 88280 0 [ide-detect ide-cd ide-disk]
cdrom 25568 0 [ide-cd]
firewall# /sbin/shorewall status
Shorewall-3.4.7 Status at firewall - Tue Feb 24 20:45:10 UTC 2009
Shorewall is running
State:Started (Tue Feb 24 19:18:40 UTC 2009)
firewall# iptables -t nat -nvL
Chain PREROUTING (policy ACCEPT 1657 packets, 113K bytes)
pkts bytes target prot opt in out source
destination
193 27099 net_dnat all -- eth0 * 0.0.0.0/0
0.0.0.0/0
Chain POSTROUTING (policy ACCEPT 133 packets, 9702 bytes)
pkts bytes target prot opt in out source
destination
1246 63116 eth0_masq all -- * eth0 0.0.0.0/0
0.0.0.0/0
Chain OUTPUT (policy ACCEPT 219 packets, 20625 bytes)
pkts bytes target prot opt in out source
destination
Chain eth0_masq (1 references)
pkts bytes target prot opt in out source
destination
1114 53472 MASQUERADE all -- * * 192.168.0.0/24
0.0.0.0/0
Chain net_dnat (1 references)
pkts bytes target prot opt in out source
destination
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28111 to:192.168.0.11
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28111 to:192.168.0.11
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28112 to:192.168.0.12
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28112 to:192.168.0.12
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28113 to:192.168.0.13
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28113 to:192.168.0.13
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28114 to:192.168.0.14
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28114 to:192.168.0.14
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28115 to:192.168.0.15
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28115 to:192.168.0.15
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28116 to:192.168.0.16
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28116 to:192.168.0.16
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28117 to:192.168.0.17
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28117 to:192.168.0.17
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28118 to:192.168.0.18
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28118 to:192.168.0.18
0 0 DNAT tcp -- * * 0.0.0.0/0
0.0.0.0/0 tcp dpt:28119 to:192.168.0.19
0 0 DNAT udp -- * * 0.0.0.0/0
0.0.0.0/0 udp dpt:28119 to:192.168.0.19
------- end of info -----------
And my messages:
------- start of messages -----------
Feb 24 19:18:34 firewall syslogd 1.4.1: restart.
Feb 24 19:18:34 firewall kernel: klogd 1.4.1, log source = /proc/kmsg
started.
Feb 24 19:18:34 firewall kernel: BIOS-provided physical RAM map:
Feb 24 19:18:34 firewall kernel: 64MB LOWMEM available.
Feb 24 19:18:34 firewall kernel: Initializing CPU#0
Feb 24 19:18:34 firewall kernel: Memory: 62544k/65536k available (864k
kernel code, 2604k reserved, 97k data, 60k init, 0k highmem)
Feb 24 19:18:34 firewall kernel: Dentry cache hash table entries: 8192
(order: 4, 65536 bytes)
Feb 24 19:18:34 firewall kernel: Inode cache hash table entries: 4096
(order: 3, 32768 bytes)
Feb 24 19:18:34 firewall kernel: Mount cache hash table entries: 512
(order: 0, 4096 bytes)
Feb 24 19:18:34 firewall kernel: Buffer cache hash table entries: 4096
(order: 2, 16384 bytes)
Feb 24 19:18:34 firewall kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Feb 24 19:18:34 firewall kernel: CPU: L2 cache: 512K
Feb 24 19:18:34 firewall kernel: Checking 'hlt' instruction... OK.
Feb 24 19:18:34 firewall kernel: PCI: PCI BIOS revision 2.10 entry at
0xfd943, last bus=1
Feb 24 19:18:34 firewall kernel: PCI: Using configuration type 1
Feb 24 19:18:34 firewall kernel: PCI: Probing PCI hardware
Feb 24 19:18:34 firewall kernel: PCI: Using IRQ router PIIX/ICH
[8086/7110] at 00:07.0
Feb 24 19:18:34 firewall kernel: Limiting direct PCI/PCI transfers.
Feb 24 19:18:34 firewall kernel: Linux NET4.0 for Linux 2.4
Feb 24 19:18:34 firewall kernel: Based upon Swansea University Computer
Society NET3.039
Feb 24 19:18:34 firewall kernel: Serial driver version 5.05c
(2001-07-08) with MANY_PORTS SHARE_IRQ DETECT_IRQ SERIAL_PCI enabled
Feb 24 19:18:34 firewall kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Feb 24 19:18:34 firewall kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Feb 24 19:18:34 firewall kernel: Real Time Clock Driver v1.10f
Feb 24 19:18:34 firewall kernel: Floppy drive(s): fd0 is 1.44M
Feb 24 19:18:34 firewall kernel: FDC 0 is a National Semiconductor PC87306
Feb 24 19:18:34 firewall kernel: Initializing Cryptographic API
Feb 24 19:18:34 firewall kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Feb 24 19:18:34 firewall kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Feb 24 19:18:34 firewall kernel: IP: routing cache hash table of 512
buckets, 4Kbytes
Feb 24 19:18:34 firewall kernel: TCP: Hash tables configured
(established 4096 bind 8192)
Feb 24 19:18:34 firewall kernel: NET4: Unix domain sockets 1.0/SMP for
Linux NET4.0.
Feb 24 19:18:34 firewall kernel: RAMDISK: Compressed image found at block 0
Feb 24 19:18:34 firewall kernel: Freeing initrd memory: 395k freed
Feb 24 19:18:34 firewall kernel: Freeing unused kernel memory: 60k freed
Feb 24 19:18:34 firewall kernel: Uniform Multi-Platform E-IDE driver
Revision: 7.00beta4-2.4
Feb 24 19:18:34 firewall kernel: ide: Assuming 33MHz system bus speed
for PIO modes; override with idebus=xx
Feb 24 19:18:34 firewall kernel: hda: ATAPI 32X CD-ROM drive, 256kB Cache
Feb 24 19:18:34 firewall kernel: Uniform CD-ROM driver Revision: 3.12
Feb 24 19:18:34 firewall kernel: 8139too Fast Ethernet driver 0.9.26
Feb 24 19:18:34 firewall kernel: PCI: Found IRQ 11 for device 00:0e.0
Feb 24 19:18:34 firewall kernel: eth0: RealTek RTL8139 at 0xc4846c00,
00:0a:cd:00:91:71, IRQ 11
Feb 24 19:18:34 firewall kernel: PCI: Found IRQ 9 for device 00:10.0
Feb 24 19:18:34 firewall kernel: PCI: Sharing IRQ 9 with 00:07.2
Feb 24 19:18:34 firewall kernel: eth1: RealTek RTL8139 at 0xc4848800,
00:0a:cd:00:99:f9, IRQ 9
Feb 24 19:18:34 firewall kernel: IPP2P v0.8.2 loading
Feb 24 19:18:34 firewall kernel: Software Watchdog Timer: 0.05, timer
margin: 60 sec
Feb 24 19:18:34 firewall kernel: parport0: PC-style at 0x378 [PCSPP(,...)]
Feb 24 19:18:34 firewall kernel: lp0: using parport0 (polling).
Feb 24 19:18:34 firewall kernel: eth0: link up, 100Mbps, full-duplex,
lpa 0x41E1
Feb 24 19:18:34 firewall dhcpcd.exe: interface eth0 has been configured
with new IP=212.76.51.79
Feb 24 19:18:34 firewall kernel: eth1: link up, 100Mbps, full-duplex,
lpa 0x45E1
Feb 24 19:18:40 firewall root: Shorewall started
------- end of messages -----------
I'm using boot CD maked with isolinux. Works. Nearly. Samba printer
doesn't work. My windows machine doesn't see the net path to printer.
Seems the HOW-TO is old.
My isolinux.cfg:
------- start of file -----------
display syslinux.dpy
timeout 0
append reboot=bios
default linux initrd=initrd.lrp init=/linuxrc rw root=/dev/ram0
LEAFCFG=/dev/cdrom:iso9660 PKGPATH=/dev/fd0:msdos,/dev/cdrom:iso9660
syst_size=22M tmp_size=226M log_size=4M
------- end of file -----------
My leaf.cfg:
------- start of file -----------
# This file is parsed as a shell script
# Kernel command line parameters are available as KCMD_<variable>
# ie: KCMD_LRP contains the LRP= portion of the kernel command line
# NOTE: For kernel command line settings that do not include an equals
# sign (ie: rw or similar), the variable is set to itself, allowing
# for easy testing (ie: KCMD_rw=rw).
# LRP and PKGPATH variables now support whitespace (space, tab, newline)
# as well as commas for seperators.
# Uncomment for more verbose execution.
#VERBOSE=1
# Other variables you might want to set in this file include:
# LRP Packages to load
# PKGPATH Device(s) to load packages from
# CONFIGDB Configuration database
# MODDB Modules database
# syst_size Size of root ramdisk
# tmp_size Size of /tmp ramdisk
# log_size Size of /var/log ramdisk
# Example:
#LRP="$KCMD_LRP rsync"
LRP="root config etc modules iptables dhcpcd shorwall ulogd dnsmasq
dropbear mhttpd openntpd webconf p9100 hdsupp netstatn samba sftp snort"
# The first entry is the backup device.
# If equal packages exist on multiple devices, the ones on the left most
device have precedence.
# PKGPATH="/dev/fd0u1680:msdos"
# Experts only: the name of the config and modules databases can be
changed, choose an unique name.
#CONFIFGDB=configdb
#MODDB=moddb
#syst_size=6M
#log_size=2M
syst_size=22M
tmp_size=226M
log_size=4M
------- end of file -----------
Samba configuration file:
------- start of file -----------
# Global parameters
[global]
workgroup = DOMEK
netbios name = spfw
guest account = pcguest
encrypt passwords = yes
wins support = yes
name resolve order = wins lmhosts hosts bcast
log file = /var/log
[homes]
comment = All printers
path = /tmp/storage/tmp
create mask = 0700
print ok = Yes
read only = No
browseable = No
[hp5550samba]
path = /tmp/storage/tmp/samba
read only = No
# quest ok = Yes
min print space = 128
print ok = Yes
printer name = lp
oplocks = No
share modes = No
------- end of file -----------
and finally inittab:
------- start of file -----------
# /etc/inittab: configuration.
# Boot-time system configuration/initialization script.
::sysinit:/etc/init.d/rcS
::sysinit:mkdir /tmp/storage
::sysinit:mkdir /tmp/storage/spool
::sysinit:mkdir /tmp/storage/spool/lpd
::sysinit:mkdir /tmp/storage/tmp
::sysinit:mkdir /tmp/storage/tmp/samba
::sysinit:chown nobody /tmp/storage/tmp/samba
::wait:/etc/init.d/rc 2
::wait:echo "lp:lp=/dev/lp0:sd=/tmp/storage/spool/lpd:mx#0:sh" >
/etc/printcap
# /sbin/getty invocations for selected ttys
#
# Format:
# <id>::<action>:<process>
tty1::respawn:/sbin/getty 38400 tty1
tty2::respawn:/sbin/getty 38400 tty2
# Example how to put a getty on a serial line (for a terminal)
#
#ttyS0::respawn:/sbin/getty -L ttyS0 19200 vt100
#ttyS1::respawn:/sbin/getty -L ttyS1 19200 vt100
# Example how to put a getty on a modem line.
#
#ttyS3::respawn:/sbin/mgetty -x0 -s 57600 ttyS3
# Stuff to do when restarting the init process
::restart:/sbin/init
# Stuff to do before rebooting
::ctrlaltdel:/sbin/reboot
::shutdown:/etc/init.d/rc 0
------- end of file -----------
In the HOW-TO is written, that I ought to use smb.lrp and lpd.lrp. But
in version 3.1 i don't see them. I use samba.lrp in that place. And I
didn't modify /var/lib/lrpkg/root.dev.mk and
/var/lib/lrpkg/root.dev.mod. p910nd works with out that.
I want to change p910nd with samba printer. Maybe I must prepare
/var/lib/lrpkg/root.dev.mk and /var/lib/lrpkg/root.dev.mod, burn them
and copy them to /var/lib/lrpkg in inittab after mounting CD?
Maybe I must delete p910nd from packages list? Maybe I must do somethig
else. But what?
------------------------------------------------------------------------------
Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA
-OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise
-Strategies to boost innovation and cut costs with open source participation
-Receive a $600 discount off the registration fee with the source code: SFAD
http://p.sf.net/sfu/XcvMzF8H
------------------------------------------------------------------------
leaf-user mailing list: [email protected]
https://lists.sourceforge.net/lists/listinfo/leaf-user
Support Request -- http://leaf-project.org/
