2008/2/23, Ysangkok <[EMAIL PROTECTED]>: > 2008/2/22, David Santinoli <[EMAIL PROTECTED]>: > > > On Fri, Feb 22, 2008 at 04:39:05PM +0100, Ysangkok wrote: > > > However I cannot get it to work. I have fetched the firmware > > > dvb-usb-dib0700-1.10.fw (34306 bytes). When I use (dvb)scan I get > > > "tuning failed". > > > > > > Hi Ysangkok, > > I have a Nova-T Stick very similar to yours (mine has USB > > vendor:product ID 2040:7060 while yours is 2040:7070). Assuming the > > hardware is substantially the same, you might want to 'modprobe mt2060' > > and check for this line in the dmesg output: > > > > MT2060: successfully identified (IF1 = 1220) > > > > Cheers, > > > > David > > > > > Hello David, > > I modprobe'd mt2060, however it doesn't render any additional lines in > dmesg. The module does show up in lsmod (attached). > > Anyway, I forgot to tell you that I _did_ compile the latest linux-dvb > git tree (about three days ago), however I am using the default Ubuntu > kernel (2.6.22-14-generic). However if I compiled my own linux-dvb I > understood that I did not need to have the absolute latest kernel. > > Next time I reboot I'll check what makes it show all those error > messages in dmesg. > > I have an old syslog which has all the error messages, which look like this: > > Feb 21 09:44:35 Gigabob kernel: [ 541.199844] dib0700: RC Query Failed > Feb 21 09:44:35 Gigabob kernel: [ 541.199856] dvb-usb: error while > querying for an remote control event. > Feb 21 09:44:35 Gigabob kernel: [ 541.351680] dib0700: RC Query Failed > Feb 21 09:44:35 Gigabob kernel: [ 541.351692] dvb-usb: error while > querying for an remote control event. > Feb 21 09:44:35 Gigabob kernel: [ 541.503522] dib0700: RC Query Failed > Feb 21 09:44:35 Gigabob kernel: [ 541.503538] dvb-usb: error while > querying for an remote control event. > Feb 21 09:44:36 Gigabob kernel: [ 541.655351] dib0700: RC Query Failed > > And it goes on like that :P > > The full syslog is 2,5 MB. I can upload if you wan't it, but there is > not anything special. > > Regards, > Ysangkok >
Hello again, I am sorry for top posting in the past. I forgot that I shouldn't. I thought maybe that the firmware was wrong. Since the device works in Vista, maybe I should try stealing its firmware. However, I do not know how to do this. I am also wondering if I can just boot into Vista and let it load the firmware. If I then reboot, I wonder if the firmware will still be in the stick, so Linux can use it? BTW, here's the output from dvbscan: $ scan -vvvvvvvv /usr/share/doc/dvb-utils/examples/scan/dvb-t/dk-Copenhagen scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/dk-Copenhagen using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 714000000 0 3 9 1 1 0 0 >>> tune to: >>> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_3_4:FEC_AUTO:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 WARNING: >>> tuning failed!!! >>> tune to: >>> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_3_4:FEC_AUTO:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE (tuning failed) >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 >>> tuning status == 0x01 WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. No output in dmesg. Regards, Janus Troelsen _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
