Riccardo Castellani wrote: > I bought it directly from store. > Several weeks ago I had problems with IDE cable and I could see UDMA5 > (with "hdparm" command) inside UDMA modes list. UDMA was the current > active mode. > Then I replaced 80- wire cable and I needed (for other reasons) again > to reinstall operating system FC3 and now I'm here.
Well you probably answered the question yourself now, you must have installed a cable only capable of udma2/udma 33. The older ide cables have sligthly thicker lines than the >udma2 cables, they have the same connector and of course there are mire connected pins on the >udma2 cables but you don't see that if looking at the connector. > > ----- Original Message ----- From: "Stefan" <[EMAIL PROTECTED]> > To: "Riccardo Castellani" <[EMAIL PROTECTED]> > Cc: <[email protected]> > Sent: Tuesday, September 06, 2005 9:59 AM > Subject: Re: > > >> Riccardo Castellani wrote: >> >>> My HD supports U-ATA 133 while motherboard supports U-ATA 100. >>> (Fedora Core 3) >>> DMA works at 33 Mhz (UDMA2) !?! >>> WHY ? How Can I set to UDMA5 ? >> >> >> To change to udma5 run: >> >> hdparm -X udma5 >> >>> >>> >>> With "hdparm -i /dev/hda" I can see: >>> >>> Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y23TZR2C >>> Config={ Fixed } >>> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57 >>> BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16 >>> CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=160086528 >>> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} >>> PIO modes: pio0 pio1 pio2 pio3 pio4 >>> DMA modes: mdma0 mdma1 mdma2 >>> UDMA modes: udma0 udma1 *udma2 >>> AdvancedPM=yes: disabled (255) WriteCache=enabled >>> Drive conforms to: (null): >> >> >> >> Looks like the drive was switched to only support UDMA2, did you buy >> this drive directly from store? >> This drive can be set to only support udma2 with the help of maxtors >> utility, this is sometimes needed to fix problems with older boards, >> so if you bought this drive from someone, there is a chance, that this >> person switched the udma mode for that drive. >> If you got it directly from a store, then this should not be the case. >> >>> >>> >>> >>> dmesg gives: >>> >>> Linux version 2.6.12-1.1376_FC3 ([EMAIL PROTECTED]) >>> (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #1 Fri Aug 26 23:27:26 >>> EDT 2005 >>> BIOS-provided physical RAM map: >>> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) >>> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) >>> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) >>> BIOS-e820: 0000000000100000 - 000000000fff0000 (usable) >>> BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data) >>> BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS) >>> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) >>> 0MB HIGHMEM available. >>> 255MB LOWMEM available. >>> Using x86 segment limits to approximate NX protection >>> On node 0 totalpages: 65520 >>> DMA zone: 4096 pages, LIFO batch:1 >>> Normal zone: 61424 pages, LIFO batch:31 >>> HighMem zone: 0 pages, LIFO batch:1 >>> DMI 2.3 present. >>> ACPI: RSDP (v000 AMI ) @ 0x000fc570 >>> ACPI: RSDT (v001 AMIINT VIA_P6 0x00000010 MSFT 0x00000097) @ >>> 0x0fff0000 >>> ACPI: FADT (v001 AMIINT VIA_P6 0x00000011 MSFT 0x00000097) @ >>> 0x0fff0030 >>> ACPI: DSDT (v001 VIA APOLLO-P 0x00001000 MSFT 0x0100000b) @ >>> 0x00000000 >>> ACPI: BIOS age (2000) fails cutoff (2001), acpi=force is required to >>> enable ACPI >>> ACPI: Disabling ACPI support >>> Allocating PCI resources starting at 10000000 (gap: 10000000:efff0000) >>> Built 1 zonelists >>> Kernel command line: ro root=LABEL=/ >>> Initializing CPU#0 >>> CPU 0 irqstacks, hard=c0447000 soft=c0446000 >>> PID hash table entries: 1024 (order: 10, 16384 bytes) >>> Detected 798.270 MHz processor. >>> Using tsc for high-res timesource >>> Console: colour VGA+ 80x25 >>> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) >>> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) >>> Memory: 254828k/262080k available (2450k kernel code, 6572k reserved, >>> 694k data, 180k init, 0k highmem) >>> Checking if this processor honours the WP bit even in supervisor >>> mode... Ok. >>> Calibrating delay loop... 1568.76 BogoMIPS (lpj=784384) >>> Security Framework v1.0.0 initialized >>> SELinux: Initializing. >>> SELinux: Starting in permissive mode >>> selinux_register_security: Registering secondary module capability >>> Capability LSM initialized as secondary >>> Mount-cache hash table entries: 512 >>> CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 >>> 00000000 00000000 00000000 >>> CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 >>> 00000000 00000000 00000000 >>> CPU: L1 I cache: 16K, L1 D cache: 16K >>> CPU: L2 cache: 256K >>> CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 >>> 00000000 00000000 00000000 >>> Intel machine check architecture supported. >>> Intel machine check reporting enabled on CPU#0. >>> CPU: Intel Pentium III (Coppermine) stepping 06 >>> Enabling fast FPU save and restore... done. >>> Enabling unmasked SIMD FPU exception support... done. >>> Checking 'hlt' instruction... OK. >>> checking if image is initramfs... it is >>> Freeing initrd memory: 399k freed >>> NET: Registered protocol family 16 >>> PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1 >>> PCI: Using configuration type 1 >>> mtrr: v2.0 (20020519) >>> ACPI: Subsystem revision 20050729 >>> ACPI: Interpreter disabled. >>> Linux Plug and Play Support v0.97 (c) Adam Belay >>> pnp: PnP ACPI: disabled >>> usbcore: registered new driver usbfs >>> usbcore: registered new driver hub >>> PCI: Probing PCI hardware >>> PCI: Probing PCI hardware (bus 00) >>> Boot video device is 0000:01:00.0 >>> PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0 >>> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) >>> audit: initializing netlink socket (disabled) >>> audit(1125948457.147:1): initialized >>> Total HugeTLB memory allocated, 0 >>> VFS: Disk quotas dquot_6.5.1 >>> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >>> SELinux: Registering netfilter hooks >>> Initializing Cryptographic API >>> ksign: Installing public key data >>> Loading keyring >>> - Added public key ACD1A80A1D789A78 >>> - User ID: Red Hat, Inc. (Kernel Module GPG key) >>> pci_hotplug: PCI Hot Plug PCI Core version: 0.5 >>> isapnp: Scanning for PnP cards... >>> isapnp: No Plug & Play device found >>> Real Time Clock Driver v1.12 >>> Linux agpgart interface v0.101 (c) Dave Jones >>> agpgart: Detected VIA Apollo Pro 133 chipset >>> agpgart: AGP aperture is 64M @ 0xe0000000 >>> PNP: No PS/2 controller found. Probing ports directly. >>> serio: i8042 AUX port at 0x60,0x64 irq 12 >>> serio: i8042 KBD port at 0x60,0x64 irq 1 >>> Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing >>> enabled >>> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A >>> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A >>> io scheduler noop registered >>> io scheduler anticipatory registered >>> io scheduler deadline registered >>> io scheduler cfq registered >>> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize >>> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >>> ide: Assuming 33MHz system bus speed for PIO modes; override with >>> idebus=xx >>> VP_IDE: IDE controller at PCI slot 0000:00:07.1 >>> PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0 >>> VP_IDE: chipset revision 6 >>> VP_IDE: not 100% native mode: will probe irqs later >>> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on >>> pci0000:00:07.1 >>> ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio >>> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:DMA >>> Probing IDE interface ide0... >>> hda: Maxtor 6Y080L0, ATA DISK drive >>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >>> Probing IDE interface ide1... >>> hdd: LG CD-ROM CRD-8521B, ATAPI CD/DVD-ROM drive >>> ide1 at 0x170-0x177,0x376 on irq 15 >>> hda: max request size: 128KiB >>> hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, >>> UDMA(33) >>> hda: cache flushes supported >>> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 > >>> hdd: ATAPI 52X CD-ROM drive, 128kB Cache, DMA >>> Uniform CD-ROM driver Revision: 3.20 >>> ide-floppy driver 0.99.newide >>> usbcore: registered new driver hiddev >>> usbcore: registered new driver usbhid >>> drivers/usb/input/hid-core.c: v2.01:USB HID core driver >>> mice: PS/2 mouse device common for all mice >>> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 >>> NET: Registered protocol family 2 >>> IP: routing cache hash table of 512 buckets, 16Kbytes >>> TCP established hash table entries: 16384 (order: 5, 131072 bytes) >>> TCP bind hash table entries: 16384 (order: 6, 458752 bytes) >>> TCP: Hash tables configured (established 16384 bind 16384) >>> Initializing IPsec netlink socket >>> NET: Registered protocol family 1 >>> NET: Registered protocol family 17 >>> Freeing unused kernel memory: 180k freed >>> input: AT Translated Set 2 keyboard on isa0060/serio0 >>> kjournald starting. Commit interval 5 seconds >>> EXT3-fs: mounted filesystem with ordered data mode. >>> SELinux: Disabled at runtime. >>> SELinux: Unregistering netfilter hooks >>> Floppy drive(s): fd0 is 1.44M >>> FDC 0 is a post-1991 82077 >>> 8139too Fast Ethernet driver 0.9.27 >>> PCI: Found IRQ 9 for device 0000:00:0a.0 >>> eth0: RealTek RTL8139 at 0xd800, 00:50:bf:5a:8d:bf, IRQ 9 >>> eth0: Identified 8139 chip type 'RTL-8139C' >>> USB Universal Host Controller Interface driver v2.2 >>> PCI: Found IRQ 11 for device 0000:00:07.2 >>> uhci_hcd 0000:00:07.2: UHCI Host Controller >>> uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 >>> uhci_hcd 0000:00:07.2: irq 11, io base 0x0000dc00 >>> hub 1-0:1.0: USB hub found >>> hub 1-0:1.0: 2 ports detected >>> md: Autodetecting RAID arrays. >>> md: autorun ... >>> md: ... autorun DONE. >>> EXT3 FS on hda5, internal journal >>> device-mapper: 4.4.0-ioctl (2005-01-12) initialised: >>> [EMAIL PROTECTED] >>> kjournald starting. Commit interval 5 seconds >>> EXT3 FS on hda1, internal journal >>> EXT3-fs: mounted filesystem with ordered data mode. >>> kjournald starting. Commit interval 5 seconds >>> EXT3 FS on hda2, internal journal >>> EXT3-fs: mounted filesystem with ordered data mode. >>> kjournald starting. Commit interval 5 seconds >>> EXT3 FS on hda8, internal journal >>> EXT3-fs: mounted filesystem with ordered data mode. >>> kjournald starting. Commit interval 5 seconds >>> EXT3 FS on hda3, internal journal >>> EXT3-fs: mounted filesystem with ordered data mode. >>> Adding 1052216k swap on /dev/hda7. Priority:-1 extents:1 >>> parport_pc: VIA 686A/8231 detected >>> parport_pc: probing current configuration >>> parport_pc: Current parallel port base: 0x378 >>> parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] >>> parport_pc: VIA parallel port: io=0x378, irq=7 >>> ieee1394: Initialized config rom entry `ip1394' >>> ip_tables: (C) 2000-2002 Netfilter core team >>> ip_tables: (C) 2000-2002 Netfilter core team >>> eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 >>> i2c /dev entries driver >>> NET: Registered protocol family 10 >>> Disabled Privacy Extensions on device c03d60a0(lo) >>> IPv6 over IPv4 tunneling driver >>> eth0: no IPv6 routers present >>> - >>> To unsubscribe from this list: send the line "unsubscribe linux-ide" in >>> the body of a message to [EMAIL PROTECTED] >>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> >> >> >> >> >> >> >> ___________________________________________________________ >> Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier >> anmelden: http://mail.yahoo.de >> > > ___________________________________________________________ Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden: http://mail.yahoo.de - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
