I am getting lots of these errors under moderate load.
This is a new drive, so I suspect some driver incompatibility between the
driver (AHCI) and the hard drive (WD Raptor 10K 74G).
Lspci:
00:1f.2 SATA controller: Intel Corporation 82801FR/FRW (ICH6R/ICH6RW) SATA
Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Unknown device 4356
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e400 [size=8]
Region 3: I/O ports at e000 [size=4]
Region 4: I/O ports at dc00 [size=16]
Region 5: Memory at dffffc00 (32-bit, non-prefetchable) [size=1K]
Log:
[ 841.645699] ata1.00: exception Emask 0x10 SAct 0x2 SErr 0x400100 action 0x2
frozen
[ 841.645708] ata1.00: (irq_stat 0x08000000, interface fatal error)
[ 841.645719] ata1.00: cmd 61/00:08:17:31:f1/04:00:03:00:00/40 tag 1 cdb 0x0
data 524288 out
[ 841.645721] res 40/00:18:5f:fa:b9/00:00:01:00:00/40 Emask 0x10 (ATA
bus error)
[ 841.947855] ata1: soft resetting port
[ 842.447515] ata1: softreset failed (1st FIS failed)
[ 842.447526] ata1: softreset failed, retrying in 5 secs
[ 847.445028] ata1: hard resetting port
[ 854.938851] ata1: port is slow to respond, please be patient (Status 0x80)
[ 877.923808] ata1: port failed to respond (30 secs, Status 0x80)
[ 877.923816] ata1: COMRESET failed (device not ready)
[ 877.923822] ata1: hardreset failed, retrying in 5 secs
[ 882.921328] ata1: hard resetting port
[ 883.377028] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 883.391971] ata1.00: configured for UDMA/133
[ 883.391992] ata1: EH complete
[ 883.392186] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 883.392381] sda: Write Protect is off
[ 883.392387] sda: Mode Sense: 00 3a 00 00
[ 883.392594] SCSI device sda: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 970.422983] ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x400100 action 0x2
frozen
[ 970.422993] ata1.00: (irq_stat 0x08000000, interface fatal error)
[ 970.423005] ata1.00: cmd 61/a8:00:0f:1d:cb/02:00:01:00:00/40 tag 0 cdb 0x0
data 348160 out
[ 970.423008] res 40/00:08:bf:24:cb/00:00:01:00:00/40 Emask 0x10 (ATA
bus error)
[ 970.423018] ata1.00: cmd 61/a8:08:bf:24:cb/00:00:01:00:00/40 tag 1 cdb 0x0
data 86016 out
[ 970.423021] res 40/00:08:bf:24:cb/00:00:01:00:00/40 Emask 0x10 (ATA
bus error)
[ 970.423031] ata1.00: cmd 61/08:10:97:41:c5/00:00:03:00:00/40 tag 2 cdb 0x0
data 4096 out
[ 970.423034] res 40/00:08:bf:24:cb/00:00:01:00:00/40 Emask 0x10 (ATA
bus error)
[ 970.725166] ata1: soft resetting port
[ 970.725177] ata1: softreset failed (port busy but CLO unavailable)
[ 970.725184] ata1: softreset failed, retrying in 5 secs
[ 975.722701] ata1: hard resetting port
[ 983.214510] ata1: port is slow to respond, please be patient (Status 0x80)
[ 1006.199471] ata1: port failed to respond (30 secs, Status 0x80)
[ 1006.199478] ata1: COMRESET failed (device not ready)
[ 1006.199485] ata1: hardreset failed, retrying in 5 secs
[ 1011.196989] ata1: hard resetting port
[ 1011.652683] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1011.667748] ata1.00: configured for UDMA/133
[ 1011.667766] ata1: EH complete
[ 1011.667964] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 1011.668157] sda: Write Protect is off
[ 1011.668163] sda: Mode Sense: 00 3a 00 00
[ 1011.668370] SCSI device sda: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
