Dear Linux ATA people, the SATA-Controller on Asus A8V-MX mainboard (VIA VT8251) doesn't recognize an attached SATA-Harddisk (Western Digital WD3200AAKS in my case) with kernels 2.6.19 and above. I get the error with 2.6.19, 2.6.20 and 2.6.21-rc4, but when switching back to 2.6.18.8 everything works fine. Also there are several identical reports of this problem on VIA arena and other sites, so maybe someone could fix this. Appended is the kernel output of ahci-driver both with working and with non working kernels.
Best regards, Rüdiger ----- kernel >= 2.6.19 ----- ahci 0000:00:0f.0: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:0f.0: flags: 64bit ncq pm led clo pmp pio slum part ata1: SATA max UDMA/133 cmd 0xE0804D00 ctl 0x0 bmdma 0x0 irq 221 ata2: SATA max UDMA/133 cmd 0xE0804D80 ctl 0x0 bmdma 0x0 irq 221 ata3: SATA max UDMA/133 cmd 0xE0804E00 ctl 0x0 bmdma 0x0 irq 221 ata4: SATA max UDMA/133 cmd 0xE0804E80 ctl 0x0 bmdma 0x0 irq 221 scsi0 : ahci ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) scsi1 : ahci ata2: SATA link down (SStatus 0 SControl 300) scsi2 : ahci ata3: SATA link down (SStatus 0 SControl 300) scsi3 : ahci ata4: SATA link down (SStatus 0 SControl 300) ---- kernel = 2.6.18.8 ----- ahci 0000:00:0f.0: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:0f.0: flags: 64bit ncq pm led clo pmp pio slum part ata1: SATA max UDMA/133 cmd 0xE0804D00 ctl 0x0 bmdma 0x0 irq 201 ata2: SATA max UDMA/133 cmd 0xE0804D80 ctl 0x0 bmdma 0x0 irq 201 ata3: SATA max UDMA/133 cmd 0xE0804E00 ctl 0x0 bmdma 0x0 irq 201 ata4: SATA max UDMA/133 cmd 0xE0804E80 ctl 0x0 bmdma 0x0 irq 201 scsi0 : ahci ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/133 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/133 scsi1 : ahci ata2: SATA link down (SStatus 0 SControl 300) scsi2 : ahci ata3: SATA link down (SStatus 0 SControl 300) scsi3 : ahci ata4: SATA link down (SStatus 0 SControl 300) Vendor: ATA Model: WDC WD3200AAKS-0 Rev: 12.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
