Hello Tejun, I found your patchset (20071011: libata-tj-2.6.23-20071011) and applied it against latest kernel 2.6.23
But unfortunately I have to revise your statement on your wiki: * The long boot delay on ASUS boards with on-board PMP chips should be fixed by this patchset but I don't have such a board or Sil4723 which is used on those boards, so I'm not sure. Anyone up for testing? It's not fixed... sry to tell you. ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: qc timeout (cmd 0xec) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5) ata2: failed to recover some devices, retrying in 5 secs ata2: port is slow to respond, please be patient (Status 0x80) ata2: COMRESET failed (errno=-16) ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) http://bugzilla.kernel.org/show_bug.cgi?id=8923 Thanks and regards Bjoern Olausson Heres the complete dmsg: Linux version 2.6.23 ([EMAIL PROTECTED]) (gcc version 4.1.2 (Gentoo 4.1.2)) #1 SMP PREEMPT Thu Oct 11 15:01:09 CEST 2007 Command line: root=/dev/sda3 video=nvidiafb:[EMAIL PROTECTED],mtrr,ywrap BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff80000 (usable) BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data) BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS) BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 3200 used Entering add_active_range(0, 256, 524160) 1 entries of 3200 used end_pfn_map = 1048576 DMI 2.4 present. ACPI: RSDP 000FAF20, 0024 (r2 ACPIAM) ACPI: XSDT 7FF80100, 004C (r1 A_M_I_ OEMXSDT 8000715 MSFT 97) ACPI: FACP 7FF80290, 00F4 (r3 A_M_I_ OEMFACP 8000715 MSFT 97) ACPI: DSDT 7FF80590, 9560 (r1 A0543 A0543000 0 INTL 20060113) ACPI: FACS 7FF8E000, 0040 ACPI: APIC 7FF80390, 0080 (r1 A_M_I_ OEMAPIC 8000715 MSFT 97) ACPI: OEMB 7FF8E040, 0066 (r1 A_M_I_ AMI_OEM 8000715 MSFT 97) ACPI: HPET 7FF89AF0, 0038 (r1 A_M_I_ OEMHPET 8000715 MSFT 97) ACPI: MCFG 7FF89B30, 003C (r1 A_M_I_ OEMMCFG 8000715 MSFT 97) No NUMA configuration found Faking a node at 0000000000000000-000000007ff80000 Entering add_active_range(0, 0, 159) 0 entries of 3200 used Entering add_active_range(0, 256, 524160) 1 entries of 3200 used Bootmem setup node 0 0000000000000000-000000007ff80000 Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 524160 On node 0 totalpages: 524063 DMA zone: 88 pages used for memmap DMA zone: 2813 pages reserved DMA zone: 1098 pages, LIFO batch:0 DMA32 zone: 11173 pages used for memmap DMA32 zone: 508891 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000) SMP: Allowing 4 CPUs, 2 hotplug CPUs PERCPU: Allocating 35032 bytes of per cpu data Built 1 zonelists in Node order. Total pages: 509989 Policy zone: DMA32 Kernel command line: root=/dev/sda3 video=nvidiafb:[EMAIL PROTECTED] ,mtrr,ywrap Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) time.c: Detected 2404.115 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 16384 ... CHAINHASH_SIZE: 8192 memory used by lock dependency info: 1648 kB per task-struct memory footprint: 1680 bytes Checking aperture... Memory: 2039616k/2096640k available (3927k kernel code, 56636k reserved, 2263k data, 348k init) SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=1 Calibrating delay using timer specific routine.. 4811.55 BogoMIPS (lpj=2405779) Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU 0/0 -> Node 0 using mwait in idle threads. CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) lockdep: not fixing up alternatives. ACPI: Core revision 20070126 Using local APIC timer interrupts. result 16695247 Detected 16.695 MHz APIC timer. lockdep: not fixing up alternatives. Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4808.09 BogoMIPS (lpj=2404048) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0480-04bf claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15) ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - CC, should be CB [20070126] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NET: Registered protocol family 23 Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized PCI-GART: No AMD northbridge found. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Time: tsc clocksource has been installed. pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved pnp: 00:06: ioport range 0x290-0x297 has been reserved pnp: 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved pnp: 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved pnp: 00:07: iomem range 0xfed50000-0xfed8ffff has been reserved pnp: 00:07: iomem range 0xffb00000-0xffbfffff could not be reserved pnp: 00:09: iomem range 0xfec00000-0xfec00fff has been reserved pnp: 00:09: iomem range 0xfee00000-0xfee00fff could not be reserved pnp: 00:0b: iomem range 0xf0000000-0xf3ffffff has been reserved pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved pnp: 00:0c: iomem range 0xc0000-0xdffff has been reserved pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:0c: iomem range 0x100000-0x7fffffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: c000-cfff MEM window: ebe00000-efefffff PREFETCH window: c3500000-e34fffff PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: c3400000-c34fffff PCI: Bridge: 0000:00:1c.3 IO window: b000-bfff MEM window: ebd00000-ebdfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: a000-afff MEM window: ebc00000-ebcfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.5 IO window: 9000-9fff MEM window: ebb00000-ebbfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: 8000-8fff MEM window: e3600000-ebafffff PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.4 to 64 ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 12, 16777216 bytes) TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]> Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). NTFS driver 2.1.28 [Flags: R/W]. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:06:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Processor [CPU2] (supports 8 throttling states) ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126] Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy intel_rng: FWH not detected Linux agpgart interface v0.102 floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <[EMAIL PROTECTED]> usbcore: registered new interface driver irda-usb USB IrDA support registered usbcore: registered new interface driver stir4200 usbcore: registered new interface driver mcs7780 ahci 0000:00:1f.2: version 3.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0xefffb900 irq 1274 ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 1274 ata3: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0xefffba00 irq 1274 ata4: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0xefffba80 irq 1274 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133 ata1.00: 145226112 sectors, multi 16: LBA48 NCQ (not used) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: qc timeout (cmd 0xec) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5) ata2: failed to recover some devices, retrying in 5 secs ata2: port is slow to respond, please be patient (Status 0x80) ata2: COMRESET failed (errno=-16) ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-6: Config Disk, RGL10364, max UDMA/133 ata2.00: 640 sectors, multi 1: LBA ata2.00: device is on DMA blacklist, disabling DMA ata2.00: configured for PIO4 ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133 ata3.00: 145226112 sectors, multi 16: LBA48 NCQ (not used) ata3.00: configured for UDMA/133 ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.00: ATA-7: WDC WD1600BEVS-00RST0, 04.01G04, max UDMA/133 ata4.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA Config Disk RGL1 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 1:0:0:0: [sdb] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg1 type 0 scsi 2:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 sd 2:0:0:0: [sdc] 145226112 512-byte hardware sectors (74356 MB) sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdc] 145226112 512-byte hardware sectors (74356 MB) sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sd 2:0:0:0: [sdc] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg2 type 0 scsi 3:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5 sd 3:0:0:0: [sdd] 312581808 512-byte hardware sectors (160042 MB) sd 3:0:0:0: [sdd] Write Protect is off sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdd] 312581808 512-byte hardware sectors (160042 MB) sd 3:0:0:0: [sdd] Write Protect is off sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd1 sd 3:0:0:0: [sdd] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg3 type 0 ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:02:00.0 to 64 scsi4 : ahci scsi5 : ahci ata5: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0xebbfe100 irq 17 ata6: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0xebbfe180 irq 17 ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) ata_piix 0000:00:1f.1: version 2.12 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1f.1 to 64 scsi6 : ata_piix scsi7 : ata_piix ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 PCI: Enabling device 0000:02:00.1 (0000 -> 0001) ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:02:00.1 to 64 scsi8 : pata_jmicron scsi9 : pata_jmicron ata9: PATA max UDMA/100 cmd 0x9c00 ctl 0x9880 bmdma 0x9400 irq 18 ata10: PATA max UDMA/100 cmd 0x9800 ctl 0x9480 bmdma 0x9408 irq 18 ata9.00: ATAPI: PLEXTOR DVDR PX-760A, 1.07, max UDMA/66 ata9.01: ATAPI: PLEXTOR DVD-ROM PX-130A, 1.03, max UDMA/100 ata9.00: configured for UDMA/66 ata9.01: configured for UDMA/100 scsi 8:0:0:0: CD-ROM PLEXTOR DVDR PX-760A 1.07 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 8:0:0:0: Attached scsi CD-ROM sr0 sr 8:0:0:0: Attached scsi generic sg4 type 5 scsi 8:0:1:0: CD-ROM PLEXTOR DVD-ROM PX-130A 1.03 PQ: 0 ANSI: 5 sr1: scsi3-mmc drive: 0x/50x cd/rw xa/form2 cdda tray sr 8:0:1:0: Attached scsi CD-ROM sr1 sr 8:0:1:0: Attached scsi generic sg5 type 5 I2O subsystem v1.325 i2o: max drivers = 8 Fusion MPT base driver 3.04.05 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.05 Fusion MPT SAS Host driver 3.04.05 ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 21 firewire_ohci: Added fw-ohci device 0000:01:03.0, OHCI version 1.10 ieee1394: raw1394: /dev/raw1394 device initialized ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xefffbc00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-1: new high speed USB device using ehci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ec00 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected firewire_core: created new fw device fw0 (0 config rom retries, S400) usb 1-7: new high speed USB device using ehci_hcd and address 7 usb 1-7: configuration #1 chosen from 1 choice hub 1-7:1.0: USB hub found hub 1-7:1.0: 4 ports detected usb 2-2: new low speed USB device using uhci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice usb 3-1: new low speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice usb 3-2: new full speed USB device using uhci_hcd and address 3 usb 3-2: configuration #1 chosen from 1 choice hub 3-2:1.0: USB hub found hub 3-2:1.0: 3 ports detected usb 4-2: new full speed USB device using uhci_hcd and address 2 usb 4-2: device descriptor read/64, error -71 usb 4-2: device descriptor read/64, error -71 usb 4-2: new full speed USB device using uhci_hcd and address 3 usb 4-2: device descriptor read/64, error -71 usb 4-2: device descriptor read/64, error -71 usb 4-2: new full speed USB device using uhci_hcd and address 4 usb 4-2: device not accepting address 4, error -71 usb 4-2: new full speed USB device using uhci_hcd and address 5 usb 4-2: device not accepting address 5, error -71 usb 1-1.1: new full speed USB device using ehci_hcd and address 8 usb 1-1.1: configuration #1 chosen from 1 choice usb 1-1.2: new high speed USB device using ehci_hcd and address 9 usb 1-1.2: configuration #1 chosen from 1 choice usb 1-7.1: new high speed USB device using ehci_hcd and address 10 usb 1-7.1: configuration #1 chosen from 1 choice hub 1-7.1:1.0: USB hub found hub 1-7.1:1.0: 4 ports detected usb 1-7.2: new high speed USB device using ehci_hcd and address 11 usb 1-7.2: configuration #1 chosen from 1 choice usb 1-7.3: new high speed USB device using ehci_hcd and address 12 usb 1-7.3: configuration #1 chosen from 1 choice usb 3-2.2: new full speed USB device using uhci_hcd and address 4 usb 3-2.2: configuration #1 chosen from 1 choice usb 3-2.3: new full speed USB device using uhci_hcd and address 5 usb 3-2.3: configuration #1 chosen from 1 choice usblp0: USB Bidirectional printer dev 9 if 0 alt 0 proto 2 vid 0x04A9 pid 0x10A5 usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... scsi10 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 11 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5 drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0 usbcore: registered new interface driver visor drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice i2c /dev entries driver ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 23 coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong! coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong! w83627ehf: Found W83627DHG chip at 0x290 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED] Bluetooth: HCI USB driver ver 2.9 usbcore: registered new interface driver hci_usb Bluetooth: Virtual HCI driver ver 1.2 Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCI BCSP protocol initialized Bluetooth: Broadcom Blutonium firmware driver ver 1.1 usbcore: registered new interface driver bcm203x Bluetooth: Digianswer Bluetooth USB driver ver 0.8 usbcore: registered new interface driver bpa10x Bluetooth: BlueFRITZ! USB driver ver 1.1 usbcore: registered new interface driver bfusb usbcore: registered new interface driver hiddev input: Logitech USB RECEIVER as /class/input/input2 input: USB HID v1.11 Mouse [Logitech USB RECEIVER] on usb-0000:00:1d.0-2 hiddev96: USB HID v1.10 Device [T-wins ASUS DH Remote] on usb-0000:00:1d.1-1 input: Logitech USB Receiver as /class/input/input3 input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.7-1.1 input: Logitech USB Receiver as /class/input/input4 input,hiddev97: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00: 1d.7-1.1 input: Logitech Logitech BT Mini-Receiver as /class/input/input5 input: USB HID v1.11 Keyboard [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1d.1-2.2 input: Logitech Logitech BT Mini-Receiver as /class/input/input6 input,hiddev98: USB HID v1.11 Mouse [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1d.1-2.3 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 IrCOMM protocol (Dag Brattli) Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.5 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 Bluetooth: BNEP (Ethernet Emulation) ver 1.2 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 NET: Registered protocol family 33 RxRPC: Registered security type 2 'rxkad' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation < [EMAIL PROTECTED]> ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' ieee80211_crypt: registered algorithm 'CCMP' ieee80211_crypt: registered algorithm 'TKIP' drivers/rtc/hctosys.c: unable to open rtc device (rtc0) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 348k freed ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:04:00.0 to 64 sky2 0000:04:00.0: v1.18 addr 0xebdfc000 irq 19 Yukon-EC (0xb6) rev 2 sky2 eth0: addr 00:18:f3:84:4f:8a ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:03:00.0 to 64 sky2 0000:03:00.0: v1.18 addr 0xebcfc000 irq 16 Yukon-EC (0xb6) rev 2 sky2 eth1: addr 00:18:f3:84:43:74 wmaster0: Selected rate control algorithm 'simple' phy0: hwaddr 00:15:af:09:e6:34, rtl8187 V1 + rtl8225z2 usbcore: registered new interface driver rtl8187 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1b.0 to 64 nvidia: module license 'NVIDIA' taints kernel. ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133) wlan: 0.8.4.2 (0.9.4) ath_pci: no version for "ieee80211_encap" found: kernel tainted. ath_pci: 0.9.4.5 (0.9.4) ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 23 (level, low) -> IRQ 23 ath_pci: switching rfkill capability off ath_rate_sample: 1.2 (0.9.4) ath_pci: switching per-packet transmit power control off wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP wifi0: mac 7.9 phy 4.5 radio 5.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons wifi0: Atheros 5212: mem=0xebaf0000, irq=23 ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:06:00.0 to 64 NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007 EXT3 FS on sda3, internal journal scsi 10:0:0:0: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0 sd 10:0:0:0: [sde] Attached SCSI removable disk sd 10:0:0:0: Attached scsi generic sg6 type 0 scsi 10:0:0:1: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0 sd 10:0:0:1: [sdf] Attached SCSI removable disk sd 10:0:0:1: Attached scsi generic sg7 type 0 scsi 10:0:0:2: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0 sd 10:0:0:2: [sdg] Attached SCSI removable disk sd 10:0:0:2: Attached scsi generic sg8 type 0 scsi 10:0:0:3: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0 sd 10:0:0:3: [sdh] Attached SCSI removable disk sd 10:0:0:3: Attached scsi generic sg9 type 0 usb-storage: device scan complete ath_rate_amrr: 0.1 (0.9.4) ath_rate_onoe: 1.0 (0.9.4) wlan: mac acl policy registered Linux video capture interface: v2.00 bttv: driver version 0.9.17 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture vboxdrv: Trying to deactivate the NMI watchdog permanently... vboxdrv: Successfully done. Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k sky2 eth0: enabling interface ADDRCONF(NETDEV_UP): eth0: link is not ready sky2 eth0: Link is up at 1000 Mbps, full duplex, flow control both ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ath0: no IPv6 routers present eth0: no IPv6 routers present - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
