On Tue, Apr 04, 2017 at 05:44:31PM +0200, Hugues Fruchet wrote:
> This adds documentation of device tree bindings for the STM32 DCMI
> (Digital Camera Memory Interface).
>
> Signed-off-by: Hugues Fruchet <hugues.fruc...@st.com>
> ---
> .../devicetree/bindings/media/st,stm32-dcmi.txt | 46
> ++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
One nit below, otherwise:
Acked-by: Rob Herring <r...@kernel.org>
>
> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> new file mode 100644
> index 0000000..c0f6f4b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
> @@ -0,0 +1,46 @@
> +STMicroelectronics STM32 Digital Camera Memory Interface (DCMI)
> +
> +Required properties:
> +- compatible: "st,stm32-dcmi"
> +- reg: physical base address and length of the registers set for the device
> +- interrupts: should contain IRQ line for the DCMI
> +- resets: reference to a reset controller,
> + see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
> +- clocks: list of clock specifiers, corresponding to entries in
> + the clock-names property
> +- clock-names: must contain "mclk", which is the DCMI peripherial clock
> +- pinctrl: the pincontrol settings to configure muxing properly
> + for pins that connect to DCMI device.
> + See
> Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt.
> +- dmas: phandle to DMA controller node,
> + see Documentation/devicetree/bindings/dma/stm32-dma.txt
> +- dma-names: must contain "tx", which is the transmit channel from DCMI to
> DMA
> +
> +DCMI supports a single port node with parallel bus. It should contain one
> +'port' child node with child 'endpoint' node. Please refer to the bindings
> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +
> + dcmi: dcmi@50050000 {
> + compatible = "st,stm32-dcmi";
> + reg = <0x50050000 0x400>;
> + interrupts = <78>;
> + resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
> + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
> + clock-names = "mclk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&dcmi_pins>;
> + dmas = <&dma2 1 1 0x414 0x3>;
> + dma-names = "tx";
> + port {
> + dcmi_0: endpoint@0 {
Unit address in not valid without a reg prop, so drop it.
> + remote-endpoint = <...>;
> + bus-width = <8>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + pclk-sample = <1>;
> + };
> + };
> + };
> +
> --
> 1.9.1
>
