Hi Hans,
On Tuesday 11 February 2014 10:23:03 Hans Verkuil wrote:
> On 02/05/14 17:42, Laurent Pinchart wrote:
> > Parse the device tree node to populate platform data.
> >
> > Cc: devicet...@vger.kernel.org
> > Signed-off-by: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
> > ---
> >
> > .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++
> > drivers/media/i2c/adv7604.c | 101 ++++++++++++++--
> > 2 files changed, 143 insertions(+), 14 deletions(-)
> > create mode 100644
> > Documentation/devicetree/bindings/media/i2c/adv7604.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> > b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode
> > 100644
> > index 0000000..0845c50
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> > @@ -0,0 +1,56 @@
> > +* Analog Devices ADV7604/11 video decoder with HDMI receiver
> > +
> > +The ADV7604 and ADV7611 are multiformat video decoders with an integrated
> > HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one
> > analog input, +and the ADV7611 has one HDMI input and no analog input.
> > +
> > +Required Properties:
> > +
> > + - compatible: Must contain one of the following
> > + - "adi,adv7604" for the ADV7604
> > + - "adi,adv7611" for the ADV7611
> > +
> > + - reg: I2C slave address
> > +
> > + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
> > + detection pins, one per HDMI input. The active flag indicates the
> > GPIO
> > + level that enables hot-plug detection.
> > +
> > +Optional Properties:
> > +
> > + - reset-gpios: Reference to the GPIO connected to the device's reset
> > pin. +
> > + - adi,default-input: Index of the input to be configured as default.
> > Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611.
> > +
> > + - adi,disable-power-down: Boolean property. When set forces the device
> > to + ignore the power-down pin. The property is valid for the ADV7604
> > only as + the ADV7611 has no power-down pin.
> > +
> > + - adi,disable-cable-reset: Boolean property. When set disables the HDMI
> > + receiver automatic reset when the HDMI cable is unplugged.
> > +
> > +Example:
> > +
> > + hdmi_receiver@4c {
> > + compatible = "adi,adv7611";
> > + reg = <0x4c>;
> > +
> > + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
> > + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
> > +
> > + adi,default-input = <0>;
> > +
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + };
> > + port@1 {
> > + reg = <1>;
> > + hdmi_in: endpoint {
> > + remote-endpoint = <&ccdc_in>;
> > + };
> > + };
> > + };
> > diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c
> > index e586c1c..cd8a2dc 100644
> > --- a/drivers/media/i2c/adv7604.c
> > +++ b/drivers/media/i2c/adv7604.c
> > @@ -32,6 +32,7 @@
> >
> > #include <linux/i2c.h>
> > #include <linux/kernel.h>
> > #include <linux/module.h>
> >
> > +#include <linux/of_gpio.h>
> >
> > #include <linux/slab.h>
> > #include <linux/v4l2-dv-timings.h>
> > #include <linux/videodev2.h>
> >
> > @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info
> > adv7604_chip_info[] = {>
> > },
> >
> > };
> >
> > +static struct i2c_device_id adv7604_i2c_id[] = {
> > + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] },
> > + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id);
> > +
> > +static struct of_device_id adv7604_of_id[] = {
> > + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] },
> > + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, adv7604_of_id);
> > +
> > +static int adv7604_parse_dt(struct adv7604_state *state)
>
> Put this under #ifdef CONFIG_OF.
#ifdef CONFIG_OF has been discouraged. I'll add an IS_ENABLED(CONFIG_OF) to
condition the call of adv7604_parse_dt() and let the compiler optimize the
function out, but I've been recommended to fix compilation errors instead of
using conditional compilation.
> It fails to compile if CONFIG_OF is not set (as it is in my case since this
> driver is used with a PCIe card).
What's the compilation failure ?
> > +{
> > + struct device_node *np;
> > + unsigned int i;
> > + int ret;
> > +
> > + np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node;
> > + state->info = of_match_node(adv7604_of_id, np)->data;
> > +
> > + state->pdata.disable_pwrdnb =
> > + of_property_read_bool(np, "adi,disable-power-down");
> > + state->pdata.disable_cable_det_rst =
> > + of_property_read_bool(np, "adi,disable-cable-reset");
> > +
> > + ret = of_property_read_u32(np, "adi,default-input",
> > + &state->pdata.default_input);
> > + if (ret < 0)
> > + state->pdata.default_input = -1;
> > +
> > + for (i = 0; i < state->info->num_dv_ports; ++i) {
> > + enum of_gpio_flags flags;
> > +
> > + state->pdata.hpd_gpio[i] =
> > + of_get_named_gpio_flags(np, "hpd-gpios", i, &flags);
> > + if (IS_ERR_VALUE(state->pdata.hpd_gpio[i]))
> > + continue;
> > +
> > + state->pdata.hpd_gpio_low[i] = flags == OF_GPIO_ACTIVE_LOW;
> > + }
> > +
> > + /* Disable the interrupt for now as no DT-based board uses it. */
> > + state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED;
> > +
> > + /* Use the default I2C addresses. */
> > + state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22;
> > + state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24;
> > +
> > + /* HACK: Hardcode the remaining platform data fields. */
> > + state->pdata.blank_data = 1;
> > + state->pdata.op_656_range = 1;
> > + state->pdata.alt_data_sat = 1;
> > + state->pdata.insert_av_codes = 1;
> > + state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0;
> > +
> > + return 0;
> > +}
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
