On 05/20/2015 06:39 PM, William Towle wrote:
> From: Rob Taylor <rob.tay...@codethink.co.uk>
> 
> Fix rcar_vin_try_fmt to use the correct pad number when calling the
> subdev set_fmt. Previously pad number 0 was always used, resulting in
> EINVAL if the subdev cares about the pad number (e.g. ADV7612).
> 
> Signed-off-by: William Towle  Taylor <rob.tay...@codethink.co.uk>
> Reviewed-by: Rob Taylor <rob.tay...@codethink.co.uk>
> ---
>  drivers/media/platform/soc_camera/rcar_vin.c |   29 
> +++++++++++++++++---------
>  1 file changed, 19 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/media/platform/soc_camera/rcar_vin.c 
> b/drivers/media/platform/soc_camera/rcar_vin.c
> index b4e9b43..571ab20 100644
> --- a/drivers/media/platform/soc_camera/rcar_vin.c
> +++ b/drivers/media/platform/soc_camera/rcar_vin.c
> @@ -1707,12 +1707,13 @@ static int rcar_vin_try_fmt(struct soc_camera_device 
> *icd,
>       const struct soc_camera_format_xlate *xlate;
>       struct v4l2_pix_format *pix = &f->fmt.pix;
>       struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
> -     struct v4l2_subdev_pad_config pad_cfg;
> +     struct v4l2_subdev_pad_config pad_cfg[sd->entity.num_pads];

Same problem: this relies on the presence of CONFIG_MEDIA_CONTROLLER.
This array can also get large which is bad when it is on the stack.

Laurent, I remember that you had plans to add an op that would allocate
and initialize this for you. Any progress on that?

Regards,

        Hans

>       struct v4l2_subdev_format format = {
>               .which = V4L2_SUBDEV_FORMAT_TRY,
>       };
>       struct v4l2_mbus_framefmt *mf = &format.format;
>       __u32 pixfmt = pix->pixelformat;
> +     struct media_pad *remote_pad;
>       int width, height;
>       int ret;
>  
> @@ -1744,17 +1745,24 @@ static int rcar_vin_try_fmt(struct soc_camera_device 
> *icd,
>       mf->code = xlate->code;
>       mf->colorspace = pix->colorspace;
>  
> -     ret = v4l2_device_call_until_err(sd->v4l2_dev, soc_camera_grp_id(icd),
> -                                      pad, set_fmt, &pad_cfg, &format);
> +     remote_pad = media_entity_remote_pad(
> +                             &icd->vdev->entity.pads[0]);
> +     format.pad = remote_pad->index;
> +
> +     ret = v4l2_device_call_until_err(sd->v4l2_dev,
> +                                     soc_camera_grp_id(icd), pad,
> +                                     set_fmt, pad_cfg,
> +                                     &format);
>       if (ret < 0)
>               return ret;
>  
> -     /* Adjust only if VIN cannot scale */
> -     if (pix->width > mf->width * 2)
> -             pix->width = mf->width * 2;
> -     if (pix->height > mf->height * 3)
> -             pix->height = mf->height * 3;
> -
> +     /*  In case the driver has adjusted 'fmt' to match the
> +      *  resolution of the live stream, 'pix' needs to pass this
> +      *  change out so that the buffer userland creates for the
> +      *  captured image/video has these dimensions
> +      */
> +     pix->width = mf->width;
> +     pix->height = mf->height;
>       pix->field = mf->field;
>       pix->colorspace = mf->colorspace;
>  
> @@ -1769,9 +1777,10 @@ static int rcar_vin_try_fmt(struct soc_camera_device 
> *icd,
>                        */
>                       mf->width = VIN_MAX_WIDTH;
>                       mf->height = VIN_MAX_HEIGHT;
> +                     format.pad = remote_pad->index;
>                       ret = v4l2_device_call_until_err(sd->v4l2_dev,
>                                                        soc_camera_grp_id(icd),
> -                                                      pad, set_fmt, &pad_cfg,
> +                                                      pad, set_fmt, pad_cfg,
>                                                        &format);
>                       if (ret < 0) {
>                               dev_err(icd->parent,
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to