* Nishant Kamat <[EMAIL PROTECTED]> [080502 04:26]:
> This adds basic board support for the OMAP3430 LDP development platform.
> It adds support for the touchscreen, RTC, UART and MMC - all of which work
> with little or no changes w.r.t. the OMAP3430 SDP.
>
> Signed-off-by: Nishant Kamat <[EMAIL PROTECTED]>
> ---
> arch/arm/mach-omap2/Kconfig | 4 +
> arch/arm/mach-omap2/Makefile | 2 +
> arch/arm/mach-omap2/board-ldp.c | 251
> +++++++++++++++++++++++++++++++++
> include/asm-arm/arch-omap/board-ldp.h | 34 +++++
> include/asm-arm/arch-omap/hardware.h | 4 +
> include/linux/i2c/twl4030.h | 2 +
> 6 files changed, 297 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/mach-omap2/board-ldp.c
> create mode 100644 include/asm-arm/arch-omap/board-ldp.h
>
> diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
> index 5c229cc..d38f8ca 100644
> --- a/arch/arm/mach-omap2/Kconfig
> +++ b/arch/arm/mach-omap2/Kconfig
> @@ -98,6 +98,10 @@ config MACH_OMAP_2430SDP
> bool "OMAP 2430 SDP board"
> depends on ARCH_OMAP2 && ARCH_OMAP2430
>
> +config MACH_OMAP_LDP
> + bool "OMAP 3 LDP board"
> + depends on ARCH_OMAP3 && ARCH_OMAP34XX
> +
> config MACH_OMAP_2430OSK
> bool "OMAP 2430 OSK board"
> depends on ARCH_OMAP2 && ARCH_OMAP24XX
> diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
> index 512b446..f58d341 100644
> --- a/arch/arm/mach-omap2/Makefile
> +++ b/arch/arm/mach-omap2/Makefile
> @@ -41,6 +41,8 @@ obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o
> obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o \
> usb-musb.o usb-ehci.o \
> hsmmc.o
> +obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o \
> + hsmmc.o
> obj-$(CONFIG_MACH_OMAP_APOLLON) += board-apollon.o \
> board-apollon-mmc.o \
> board-apollon-keys.o
> diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
> new file mode 100644
> index 0000000..4994dd8
> --- /dev/null
> +++ b/arch/arm/mach-omap2/board-ldp.c
> @@ -0,0 +1,251 @@
> +/*
> + * linux/arch/arm/mach-omap2/board-ldp.c
> + *
> + * Copyright (C) 2008 Texas Instruments Inc.
> + * Nishant Kamat <[EMAIL PROTECTED]>
> + *
> + * Modified from mach-omap2/board-3430sdp.c
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <linux/delay.h>
> +#include <linux/input.h>
> +#include <linux/workqueue.h>
> +#include <linux/err.h>
> +#include <linux/clk.h>
> +#include <linux/spi/spi.h>
> +#include <linux/spi/ads7846.h>
> +#include <linux/i2c/twl4030.h>
> +#include <linux/i2c/twl4030-rtc.h>
> +
> +#include <asm/hardware.h>
> +#include <asm/mach-types.h>
> +#include <asm/mach/arch.h>
> +#include <asm/mach/map.h>
> +
> +#include <asm/arch/mcspi.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/board.h>
> +#include <asm/arch/common.h>
> +#include <asm/arch/gpmc.h>
> +#include <asm/arch/hsmmc.h>
> +
> +#include <asm/io.h>
> +#include <asm/delay.h>
> +#include <asm/arch/control.h>
> +
> +#define ENABLE_VAUX1_DEDICATED 0x03
> +#define ENABLE_VAUX1_DEV_GRP 0x20
> +
> +#define TWL4030_MSECURE_GPIO 22
> +
> +static int ts_gpio;
> +
> +#ifdef CONFIG_RTC_DRV_TWL4030
> +static int twl4030_rtc_init(void)
> +{
> + int ret = 0;
> +
> + /* 3430ES2.0 doesn't have msecure/gpio-22 line connected to T2 */
> + if (is_device_type_gp() && is_sil_rev_less_than(OMAP3430_REV_ES2_0)) {
> + u32 msecure_pad_config_reg = omap_ctrl_base_get() + 0xA3C;
> + int mux_mask = 0x04;
> + u16 tmp;
> +
> + ret = omap_request_gpio(TWL4030_MSECURE_GPIO);
> + if (ret < 0) {
> + printk(KERN_ERR "twl4030_rtc_init: can't"
> + "reserve GPIO:%d !\n", TWL4030_MSECURE_GPIO);
> + goto out;
> + }
> + /*
> + * TWL4030 will be in secure mode if msecure line from OMAP
> + * is low. Make msecure line high in order to change the
> + * TWL4030 RTC time and calender registers.
> + */
> + omap_set_gpio_direction(TWL4030_MSECURE_GPIO, 0);
> +
> + tmp = omap_readw(msecure_pad_config_reg);
> + tmp &= 0xF8; /* To enable mux mode 03/04 = GPIO_RTC */
> + tmp |= mux_mask;/* To enable mux mode 03/04 = GPIO_RTC */
> + omap_writew(tmp, msecure_pad_config_reg);
> +
> + omap_set_gpio_dataout(TWL4030_MSECURE_GPIO, 1);
> + }
> +out:
> + return ret;
> +}
> +
> +static void twl4030_rtc_exit(void)
> +{
> + omap_free_gpio(TWL4030_MSECURE_GPIO);
> +}
> +
> +static struct twl4030rtc_platform_data ldp_twl4030rtc_data = {
> + .init = &twl4030_rtc_init,
> + .exit = &twl4030_rtc_exit,
> +};
> +
> +static struct platform_device ldp_twl4030rtc_device = {
> + .name = "twl4030_rtc",
> + .id = -1,
> + .dev = {
> + .platform_data = &ldp_twl4030rtc_data,
> + },
> +};
> +#endif
> +
> +/**
> + * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
> + *
> + * @return - void. If request gpio fails then Flag KERN_ERR.
> + */
> +static void ads7846_dev_init(void)
> +{
> + if (omap_request_gpio(ts_gpio) < 0) {
> + printk(KERN_ERR "can't get ads746 pen down GPIO\n");
> + return;
> + }
> +
> + omap_set_gpio_direction(ts_gpio, 1);
> +
> + omap_set_gpio_debounce(ts_gpio, 1);
> + omap_set_gpio_debounce_time(ts_gpio, 0xa);
> +}
> +
> +static int ads7846_get_pendown_state(void)
> +{
> + return !omap_get_gpio_datain(ts_gpio);
> +}
> +
> +/*
> + * This enable(1)/disable(0) the voltage for TS: uses twl4030 calls
> + */
> +static int ads7846_vaux_control(int vaux_cntrl)
> +{
> + int ret = 0;
> +
> +#ifdef CONFIG_TWL4030_CORE
> + /* check for return value of ldo_use: if success it returns 0 */
> + if (vaux_cntrl == VAUX_ENABLE) {
> + if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + ENABLE_VAUX1_DEDICATED, TWL4030_VAUX1_DEDICATED))
> + return -EIO;
> + if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + ENABLE_VAUX1_DEV_GRP, TWL4030_VAUX1_DEV_GRP))
> + return -EIO;
> + } else if (vaux_cntrl == VAUX_DISABLE) {
> + if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + 0x00, TWL4030_VAUX1_DEDICATED))
> + return -EIO;
> + if (ret != twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + 0x00, TWL4030_VAUX1_DEV_GRP))
> + return -EIO;
> + }
> +#else
> + ret = -EIO;
> +#endif
> + return ret;
> +}
> +
> +static struct ads7846_platform_data tsc2046_config __initdata = {
> + .get_pendown_state = ads7846_get_pendown_state,
> + .keep_vref_on = 1,
> + .vaux_control = ads7846_vaux_control,
> +};
> +
> +
> +static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
> + .turbo_mode = 0,
> + .single_channel = 1, /* 0: slave, 1: master */
> +};
> +
> +static struct spi_board_info ldp_spi_board_info[] __initdata = {
> + [0] = {
> + /*
> + * TSC2046 operates at a max freqency of 2MHz, so
> + * operate slightly below at 1.5MHz
> + */
> + .modalias = "ads7846",
> + .bus_num = 1,
> + .chip_select = 0,
> + .max_speed_hz = 1500000,
> + .controller_data = &tsc2046_mcspi_config,
> + .irq = 0,
> + .platform_data = &tsc2046_config,
> + },
> +};
> +
> +static struct platform_device *ldp_devices[] __initdata = {
> +#ifdef CONFIG_RTC_DRV_TWL4030
> + &ldp_twl4030rtc_device,
> +#endif
> +};
> +
> +static void __init omap_ldp_init_irq(void)
> +{
> + omap2_init_common_hw();
> + omap_init_irq();
> + omap_gpio_init();
> +}
> +
> +static struct omap_uart_config ldp_uart_config __initdata = {
> + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
> +};
> +
> +static struct omap_mmc_config ldp_mmc_config __initdata = {
> + .mmc [0] = {
> + .enabled = 1,
> + .wire4 = 1,
> + },
> +};
> +
> +static struct omap_board_config_kernel ldp_config[] __initdata = {
> + { OMAP_TAG_UART, &ldp_uart_config },
> + { OMAP_TAG_MMC, &ldp_mmc_config },
> +};
> +
> +static int __init omap_i2c_init(void)
> +{
> + omap_register_i2c_bus(1, 2600, NULL, 0);
> + omap_register_i2c_bus(2, 400, NULL, 0);
> + omap_register_i2c_bus(3, 400, NULL, 0);
> + return 0;
> +}
> +
> +static void __init omap_ldp_init(void)
> +{
> + platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
> + omap_board_config = ldp_config;
> + omap_board_config_size = ARRAY_SIZE(ldp_config);
> + ts_gpio = 54;
> + ldp_spi_board_info[0].irq = OMAP_GPIO_IRQ(ts_gpio);
> + spi_register_board_info(ldp_spi_board_info,
> + ARRAY_SIZE(ldp_spi_board_info));
> + ads7846_dev_init();
> + omap_serial_init();
> + hsmmc_init();
> +}
> +
> +static void __init omap_ldp_map_io(void)
> +{
> + omap2_set_globals_343x();
> + omap2_map_common_io();
> +}
> +arch_initcall(omap_i2c_init);
> +
> +MACHINE_START(OMAP_LDP, "OMAP LDP board")
> + .phys_io = 0x48000000,
> + .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
> + .boot_params = 0x80000100,
> + .map_io = omap_ldp_map_io,
> + .init_irq = omap_ldp_init_irq,
> + .init_machine = omap_ldp_init,
> + .timer = &omap_timer,
> +MACHINE_END
> diff --git a/include/asm-arm/arch-omap/board-ldp.h
> b/include/asm-arm/arch-omap/board-ldp.h
> new file mode 100644
> index 0000000..b227561
> --- /dev/null
> +++ b/include/asm-arm/arch-omap/board-ldp.h
> @@ -0,0 +1,34 @@
> +/*
> + * linux/include/asm-arm/arch-omap/board-ldp.h
> + *
> + * Hardware definitions for TI OMAP3 LDP.
> + *
> + * Copyright (C) 2008 Texas Instruments Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + *
> + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
> + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
> + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
> + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
> + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
> + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
> + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
> + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
> + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + *
> + * You should have received a copy of the GNU General Public License along
> + * with this program; if not, write to the Free Software Foundation, Inc.,
> + * 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#ifndef __ASM_ARCH_OMAP_LDP_H
> +#define __ASM_ARCH_OMAP_LDP_H
> +
> +#define TWL4030_IRQNUM INT_34XX_SYS_NIRQ
Let's patch away this first before applying these. This should really be
OMAP3_TWL4030_IRQNUM in 34xx.h
> +
> +#endif /* __ASM_ARCH_OMAP_LDP_H */
> diff --git a/include/asm-arm/arch-omap/hardware.h
> b/include/asm-arm/arch-omap/hardware.h
> index 09f8ef8..fed9a76 100644
> --- a/include/asm-arm/arch-omap/hardware.h
> +++ b/include/asm-arm/arch-omap/hardware.h
> @@ -343,6 +343,10 @@
> #include "board-omap3beagle.h"
> #endif
>
> +#ifdef CONFIG_MACH_OMAP_LDP
> +#include "board-ldp.h"
> +#endif
> +
> #ifdef CONFIG_MACH_OMAP_APOLLON
> #include "board-apollon.h"
> #endif
> diff --git a/include/linux/i2c/twl4030.h b/include/linux/i2c/twl4030.h
> index 05d07f9..40af46e 100644
> --- a/include/linux/i2c/twl4030.h
> +++ b/include/linux/i2c/twl4030.h
> @@ -77,6 +77,8 @@
> /* Offsets to Power Registers */
> #define TWL4030_VDAC_DEV_GRP 0x3B
> #define TWL4030_VDAC_DEDICATED 0x3E
> +#define TWL4030_VAUX1_DEV_GRP 0x17
> +#define TWL4030_VAUX1_DEDICATED 0x1A
> #define TWL4030_VAUX2_DEV_GRP 0x1B
> #define TWL4030_VAUX2_DEDICATED 0x1E
> #define TWL4030_VAUX3_DEV_GRP 0x1F
Please send this twl4030 patch first as a separate patch.
> --
> 1.5.3.2
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to [EMAIL PROTECTED]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
