* David Brownell <[EMAIL PROTECTED]> [080911 02:48]:
> From: David Brownell <[EMAIL PROTECTED]>
>
> Make the twl4030 RTC initialization follow the driver model better.
> The platform device is created (if needed) as part of twl4030 setup
> instead of as a board-specific thing, and fits properly into the
> driver model tree.
>
> The only minor glitch here is on boards using platform_data to pass
> MSECURE initialization hooks to the RTC driver. The right solution
> probably just removes that platform_data, and might even make Linux
> follow the principle of "least privilege" (at the hardware level!)
> instead of always holding this signal high.
>
> Pending better handling of MSECURE, this patch just does what the
> RTC init does, but earlier: MSECURE is always high, so the RTC time
> and calendar registers can be updated (and presumably a bunch of
> non-RTC privileged operations will be allowed too).
>
> Yet to be done: set up the IRQ resource; make the rtc driver use
> that IRQ resource; and properly issue wakeup alarms.
>
> Signed-off-by: David Brownell <[EMAIL PROTECTED]>
> ---
> This is an example of what was discussed earlier ... starting
> to clean up the twl4030 driver model support. More can be done
> when twl4030 becomes a new-style I2C driver; clean support for
> things like the keypad, power control, and gpio will need that to
> get proper handling for board-specific data.
>
> Note the net code shrink from "doing it right" and sharing code.
Pushing today.
Tony
>
> arch/arm/mach-omap2/board-2430sdp.c | 34 +++++--------------
> arch/arm/mach-omap2/board-3430sdp.c | 41 ++++-------------------
> arch/arm/mach-omap2/board-ldp.c | 36 ++++----------------
> arch/arm/mach-omap2/board-omap3beagle.c | 8 ----
> arch/arm/mach-omap2/board-omap3evm.c | 8 ----
> drivers/i2c/chips/twl4030-core.c | 52 ++++++++++++++++++++++++++++++
> 6 files changed, 76 insertions(+), 103 deletions(-)
>
> --- a/arch/arm/mach-omap2/board-2430sdp.c
> +++ b/arch/arm/mach-omap2/board-2430sdp.c
> @@ -24,7 +24,6 @@
> #include <linux/clk.h>
> #include <linux/spi/spi.h>
> #include <linux/spi/ads7846.h>
> -#include <linux/i2c/twl4030-rtc.h>
>
> #include <mach/hardware.h>
> #include <asm/mach-types.h>
> @@ -190,13 +189,14 @@ static struct platform_device sdp2430_kp
> },
> };
>
> -static int twl4030_rtc_init(void)
> +static int __init msecure_init(void)
> {
> int ret = 0;
>
> - ret = omap_request_gpio(TWL4030_MSECURE_GPIO);
> +#ifdef CONFIG_RTC_DRV_TWL4030
> + ret = gpio_request(TWL4030_MSECURE_GPIO, "msecure");
> if (ret < 0) {
> - printk(KERN_ERR "twl4030_rtc_init: can't reserve GPIO:%d !\n",
> + printk(KERN_ERR "msecure_init: can't reserve GPIO:%d !\n",
> TWL4030_MSECURE_GPIO);
> goto out;
> }
> @@ -205,36 +205,18 @@ static int twl4030_rtc_init(void)
> * Make msecure line high in order to change the TWL4030 RTC time
> * and calender registers.
> */
> - omap_set_gpio_direction(TWL4030_MSECURE_GPIO, 0); /*dir out */
> - omap_set_gpio_dataout(TWL4030_MSECURE_GPIO, 1);
> + gpio_direction_output(TWL4030_MSECURE_GPIO, 1);
> out:
> - return ret;
> -}
> +#endif
>
> -static void twl4030_rtc_exit(void)
> -{
> - omap_free_gpio(TWL4030_MSECURE_GPIO);
> + return ret;
> }
>
> -static struct twl4030rtc_platform_data sdp2430_twl4030rtc_data = {
> - .init = &twl4030_rtc_init,
> - .exit = &twl4030_rtc_exit,
> -};
> -
> -static struct platform_device sdp2430_twl4030rtc_device = {
> - .name = "twl4030_rtc",
> - .id = -1,
> - .dev = {
> - .platform_data = &sdp2430_twl4030rtc_data,
> - },
> -};
> -
> static struct platform_device *sdp2430_devices[] __initdata = {
> &sdp2430_smc91x_device,
> &sdp2430_flash_device,
> &sdp2430_kp_device,
> &sdp2430_lcd_device,
> - &sdp2430_twl4030rtc_device,
> };
>
> static void ads7846_dev_init(void)
> @@ -398,6 +380,8 @@ static void __init omap_2430sdp_init(voi
> omap_board_config_size = ARRAY_SIZE(sdp2430_config);
> omap_serial_init();
>
> + msecure_init();
> +
> sdp2430_flash_init();
> usb_musb_init();
>
> --- a/arch/arm/mach-omap2/board-3430sdp.c
> +++ b/arch/arm/mach-omap2/board-3430sdp.c
> @@ -20,9 +20,9 @@
> #include <linux/workqueue.h>
> #include <linux/err.h>
> #include <linux/clk.h>
> -#include <linux/i2c/twl4030.h>
> #include <linux/spi/spi.h>
> #include <linux/spi/ads7846.h>
> +#include <linux/i2c/twl4030.h>
>
> #include <mach/hardware.h>
> #include <asm/mach-types.h>
> @@ -129,20 +129,20 @@ static struct platform_device sdp3430_kp
>
> static int ts_gpio;
>
> -#ifdef CONFIG_RTC_DRV_TWL4030
> -static int twl4030_rtc_init(void)
> +static int __init msecure_init(void)
> {
> int ret = 0;
>
> +#ifdef CONFIG_RTC_DRV_TWL4030
> /* 3430ES2.0 doesn't have msecure/gpio-22 line connected to T2 */
> if (is_device_type_gp() && is_sil_rev_less_than(OMAP3430_REV_ES2_0)) {
> u32 msecure_pad_config_reg = omap_ctrl_base_get() + 0xA3C;
> int mux_mask = 0x04;
> u16 tmp;
>
> - ret = omap_request_gpio(TWL4030_MSECURE_GPIO);
> + ret = gpio_request(TWL4030_MSECURE_GPIO, "msecure");
> if (ret < 0) {
> - printk(KERN_ERR "twl4030_rtc_init: can't"
> + printk(KERN_ERR "msecure_init: can't"
> "reserve GPIO:%d !\n", TWL4030_MSECURE_GPIO);
> goto out;
> }
> @@ -151,41 +151,18 @@ static int twl4030_rtc_init(void)
> * is low. Make msecure line high in order to change the
> * TWL4030 RTC time and calender registers.
> */
> - omap_set_gpio_direction(TWL4030_MSECURE_GPIO, 0);
> -
> tmp = omap_readw(msecure_pad_config_reg);
> tmp &= 0xF8; /* To enable mux mode 03/04 = GPIO_RTC */
> tmp |= mux_mask;/* To enable mux mode 03/04 = GPIO_RTC */
> omap_writew(tmp, msecure_pad_config_reg);
>
> - omap_set_gpio_dataout(TWL4030_MSECURE_GPIO, 1);
> + gpio_direction_output(TWL4030_MSECURE_GPIO, 1);
> }
> out:
> +#endif
> return ret;
> }
>
> -static void twl4030_rtc_exit(void)
> -{
> - if (is_device_type_gp() &&
> - is_sil_rev_less_than(OMAP3430_REV_ES2_0)) {
> - omap_free_gpio(TWL4030_MSECURE_GPIO);
> - }
> -}
> -
> -static struct twl4030rtc_platform_data sdp3430_twl4030rtc_data = {
> - .init = &twl4030_rtc_init,
> - .exit = &twl4030_rtc_exit,
> -};
> -
> -static struct platform_device sdp3430_twl4030rtc_device = {
> - .name = "twl4030_rtc",
> - .id = -1,
> - .dev = {
> - .platform_data = &sdp3430_twl4030rtc_data,
> - },
> -};
> -#endif
> -
> /**
> * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
> *
> @@ -276,9 +253,6 @@ static struct platform_device *sdp3430_d
> &sdp3430_smc91x_device,
> &sdp3430_kp_device,
> &sdp3430_lcd_device,
> -#ifdef CONFIG_RTC_DRV_TWL4030
> - &sdp3430_twl4030rtc_device,
> -#endif
> };
>
> static inline void __init sdp3430_init_smc91x(void)
> @@ -367,6 +341,7 @@ static void __init omap_3430sdp_init(voi
> ARRAY_SIZE(sdp3430_spi_board_info));
> ads7846_dev_init();
> sdp3430_flash_init();
> + msecure_init();
> twl4030_bci_battery_init();
> omap_serial_init();
> usb_musb_init();
> --- a/arch/arm/mach-omap2/board-ldp.c
> +++ b/arch/arm/mach-omap2/board-ldp.c
> @@ -22,7 +22,6 @@
> #include <linux/spi/spi.h>
> #include <linux/spi/ads7846.h>
> #include <linux/i2c/twl4030.h>
> -#include <linux/i2c/twl4030-rtc.h>
>
> #include <mach/hardware.h>
> #include <asm/mach-types.h>
> @@ -48,20 +47,20 @@
>
> static int ts_gpio;
>
> -#ifdef CONFIG_RTC_DRV_TWL4030
> -static int twl4030_rtc_init(void)
> +static int __init msecure_init(void)
> {
> int ret = 0;
>
> +#ifdef CONFIG_RTC_DRV_TWL4030
> /* 3430ES2.0 doesn't have msecure/gpio-22 line connected to T2 */
> if (is_device_type_gp() && is_sil_rev_less_than(OMAP3430_REV_ES2_0)) {
> u32 msecure_pad_config_reg = omap_ctrl_base_get() + 0xA3C;
> int mux_mask = 0x04;
> u16 tmp;
>
> - ret = omap_request_gpio(TWL4030_MSECURE_GPIO);
> + ret = gpio_request(TWL4030_MSECURE_GPIO, "msecure");
> if (ret < 0) {
> - printk(KERN_ERR "twl4030_rtc_init: can't"
> + printk(KERN_ERR "msecure_init: can't"
> "reserve GPIO:%d !\n", TWL4030_MSECURE_GPIO);
> goto out;
> }
> @@ -70,38 +69,19 @@ static int twl4030_rtc_init(void)
> * is low. Make msecure line high in order to change the
> * TWL4030 RTC time and calender registers.
> */
> - omap_set_gpio_direction(TWL4030_MSECURE_GPIO, 0);
>
> tmp = omap_readw(msecure_pad_config_reg);
> tmp &= 0xF8; /* To enable mux mode 03/04 = GPIO_RTC */
> tmp |= mux_mask;/* To enable mux mode 03/04 = GPIO_RTC */
> omap_writew(tmp, msecure_pad_config_reg);
>
> - omap_set_gpio_dataout(TWL4030_MSECURE_GPIO, 1);
> + gpio_direction_output(TWL4030_MSECURE_GPIO, 1);
> }
> out:
> +#endif
> return ret;
> }
>
> -static void twl4030_rtc_exit(void)
> -{
> - omap_free_gpio(TWL4030_MSECURE_GPIO);
> -}
> -
> -static struct twl4030rtc_platform_data ldp_twl4030rtc_data = {
> - .init = &twl4030_rtc_init,
> - .exit = &twl4030_rtc_exit,
> -};
> -
> -static struct platform_device ldp_twl4030rtc_device = {
> - .name = "twl4030_rtc",
> - .id = -1,
> - .dev = {
> - .platform_data = &ldp_twl4030rtc_data,
> - },
> -};
> -#endif
> -
> /**
> * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
> *
> @@ -184,9 +164,6 @@ static struct spi_board_info ldp_spi_boa
> };
>
> static struct platform_device *ldp_devices[] __initdata = {
> -#ifdef CONFIG_RTC_DRV_TWL4030
> - &ldp_twl4030rtc_device,
> -#endif
> };
>
> static void __init omap_ldp_init_irq(void)
> @@ -230,6 +207,7 @@ static void __init omap_ldp_init(void)
> ldp_spi_board_info[0].irq = OMAP_GPIO_IRQ(ts_gpio);
> spi_register_board_info(ldp_spi_board_info,
> ARRAY_SIZE(ldp_spi_board_info));
> + msecure_init();
> ads7846_dev_init();
> omap_serial_init();
> usb_musb_init();
> --- a/arch/arm/mach-omap2/board-omap3beagle.c
> +++ b/arch/arm/mach-omap2/board-omap3beagle.c
> @@ -132,11 +132,6 @@ static struct omap_mmc_config omap3beagl
> },
> };
>
> -static struct platform_device omap3_beagle_twl4030rtc_device = {
> - .name = "twl4030_rtc",
> - .id = -1,
> -};
> -
> static struct platform_device omap3_beagle_lcd_device = {
> .name = "omap3beagle_lcd",
> .id = -1,
> @@ -202,9 +197,6 @@ static struct omap_board_config_kernel o
>
> static struct platform_device *omap3_beagle_devices[] __initdata = {
> &omap3_beagle_lcd_device,
> -#ifdef CONFIG_RTC_DRV_TWL4030
> - &omap3_beagle_twl4030rtc_device,
> -#endif
> &leds_gpio,
> &keys_gpio,
> };
> --- a/arch/arm/mach-omap2/board-omap3evm.c
> +++ b/arch/arm/mach-omap2/board-omap3evm.c
> @@ -110,11 +110,6 @@ static struct omap_lcd_config omap3_evm_
> .ctrl_name = "internal",
> };
>
> -static struct platform_device omap3_evm_twl4030rtc_device = {
> - .name = "twl4030_rtc",
> - .id = -1,
> -};
> -
> static void ads7846_dev_init(void)
> {
> if (omap_request_gpio(OMAP3_EVM_TS_GPIO) < 0)
> @@ -205,9 +200,6 @@ static struct omap_board_config_kernel o
> static struct platform_device *omap3_evm_devices[] __initdata = {
> &omap3_evm_lcd_device,
> &omap3evm_kp_device,
> -#ifdef CONFIG_RTC_DRV_TWL4030
> - &omap3_evm_twl4030rtc_device,
> -#endif
> &omap3evm_smc911x_device,
> };
>
> --- a/drivers/i2c/chips/twl4030-core.c
> +++ b/drivers/i2c/chips/twl4030-core.c
> @@ -37,6 +37,7 @@
> #include <linux/random.h>
> #include <linux/syscalls.h>
> #include <linux/kthread.h>
> +#include <linux/platform_device.h>
>
> #include <linux/i2c.h>
> #include <linux/i2c/twl4030.h>
> @@ -742,6 +743,55 @@ static int __init twl4030_detect_client(
> return err;
> }
>
> +static int add_children(void)
> +{
> + static bool children;
> +
> + struct platform_device *pdev = NULL;
> + struct twl4030_client *twl = NULL;
> + int status = 0;
> +
> + /* FIXME this doesn't yet set up platform_data for anything;
> + * it can't be available until this becomes a "new style"
> + * I2C driver. Similarly, a new style driver will know it
> + * didn't already initialize its children.
> + */
> +
> + if (children)
> + return 0;
> +
> +#ifdef CONFIG_RTC_DRV_TWL4030
> + pdev = platform_device_alloc("twl4030_rtc", -1);
> + if (pdev) {
> + twl = &twl4030_modules[TWL4030_SLAVENUM_NUM3];
> + pdev->dev.parent = &twl->client.dev;
> + device_init_wakeup(&pdev->dev, 1);
> +
> + /*
> + * FIXME add the relevant IRQ resource, and make the
> + * rtc driver use it instead of hard-wiring ...
> + *
> + * REVISIT platform_data here currently only supports
> + * setting up the "msecure" line ... which actually
> + * violates the "princple of least privilege", since
> + * it's effectively always in "high trust" mode.
> + *
> + * For now, expect equivalent treatment at board init:
> + * setting msecure high. Eventually, Linux might
> + * become more aware of those HW security concerns.
> + */
> +
> + status = platform_device_add(pdev);
> + if (status < 0)
> + platform_device_put(pdev);
> + } else
> + status = -ENOMEM;
> +#endif
> +
> + children = true;
> + return status;
> +}
> +
> /* adapter callback */
> static int __init twl4030_attach_adapter(struct i2c_adapter *adapter)
> {
> @@ -759,6 +809,8 @@ static int __init twl4030_attach_adapter
> }
> twl_i2c_adapter++;
>
> + add_children();
> +
> /*
> * Check if the PIH module is initialized, if yes, then init
> * the T2 Interrupt subsystem
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to [EMAIL PROTECTED]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
