nand transfer type (sDMA, Polled, prefetch) can be select from board file,
enabling all transfer type in driver, by default.

this helps in multi-omap build and to select different transfer type for
different board.

Signed-off-by: Sukumar Ghorai <s-gho...@ti.com>
---
 arch/arm/plat-omap/include/plat/nand.h |    7 +++
 drivers/mtd/nand/Kconfig               |   17 ------
 drivers/mtd/nand/omap2.c               |   94 ++++++++++++--------------------
 3 files changed, 41 insertions(+), 77 deletions(-)

diff --git a/arch/arm/plat-omap/include/plat/nand.h 
b/arch/arm/plat-omap/include/plat/nand.h
index 6562cd0..78c0bdb 100644
--- a/arch/arm/plat-omap/include/plat/nand.h
+++ b/arch/arm/plat-omap/include/plat/nand.h
@@ -10,6 +10,12 @@
 
 #include <linux/mtd/partitions.h>
 
+enum nand_io {
+       NAND_OMAP_PREFETCH_POLLED = 0,  /* prefetch polled mode, default */
+       NAND_OMAP_POLLED,               /* polled mode, without prefetch */
+       NAND_OMAP_PREFETCH_DMA          /* prefetch enabled sDMA mode */
+};
+
 struct omap_nand_platform_data {
        unsigned int            options;
        int                     cs;
@@ -20,6 +26,7 @@ struct omap_nand_platform_data {
        int                     (*nand_setup)(void);
        int                     (*dev_ready)(struct omap_nand_platform_data *);
        int                     dma_channel;
+       enum nand_io            xfer_type;
        unsigned long           phys_base;
        int                     devsize;
 };
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index c895922..178e200 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -106,23 +106,6 @@ config MTD_NAND_OMAP2
        help
           Support for NAND flash on Texas Instruments OMAP2 and OMAP3 
platforms.
 
-config MTD_NAND_OMAP_PREFETCH
-       bool "GPMC prefetch support for NAND Flash device"
-       depends on MTD_NAND_OMAP2
-       default y
-       help
-        The NAND device can be accessed for Read/Write using GPMC PREFETCH 
engine
-        to improve the performance.
-
-config MTD_NAND_OMAP_PREFETCH_DMA
-       depends on MTD_NAND_OMAP_PREFETCH
-       bool "DMA mode"
-       default n
-       help
-        The GPMC PREFETCH engine can be configured eigther in MPU interrupt 
mode
-        or in DMA interrupt mode.
-        Say y for DMA mode or MPU mode will be used
-
 config MTD_NAND_IDS
        tristate
 
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 7c04cd6..60bac8e 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -96,27 +96,6 @@
 static const char *part_probes[] = { "cmdlinepart", NULL };
 #endif
 
-#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH
-static int use_prefetch = 1;
-
-/* "modprobe ... use_prefetch=0" etc */
-module_param(use_prefetch, bool, 0);
-MODULE_PARM_DESC(use_prefetch, "enable/disable use of PREFETCH");
-
-#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH_DMA
-static int use_dma = 1;
-
-/* "modprobe ... use_dma=0" etc */
-module_param(use_dma, bool, 0);
-MODULE_PARM_DESC(use_dma, "enable/disable use of DMA");
-#else
-static const int use_dma;
-#endif
-#else
-const int use_prefetch;
-static const int use_dma;
-#endif
-
 struct omap_nand_info {
        struct nand_hw_control          controller;
        struct omap_nand_platform_data  *pdata;
@@ -324,7 +303,6 @@ static void omap_write_buf_pref(struct mtd_info *mtd,
        }
 }
 
-#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH_DMA
 /*
  * omap_nand_dma_cb: callback on the completion of dma transfer
  * @lch: logical channel
@@ -426,14 +404,6 @@ out_copy:
                        : omap_write_buf8(mtd, (u_char *) addr, len);
        return 0;
 }
-#else
-static void omap_nand_dma_cb(int lch, u16 ch_status, void *data) {}
-static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr,
-                                       unsigned int len, int is_write)
-{
-       return 0;
-}
-#endif
 
 /**
  * omap_read_buf_dma_pref - read data from NAND controller into buffer
@@ -842,28 +812,13 @@ static int __devinit omap_nand_probe(struct 
platform_device *pdev)
                info->nand.chip_delay = 50;
        }
 
-       if (use_prefetch) {
-
+       switch (pdata->xfer_type) {
+       case NAND_OMAP_PREFETCH_POLLED:
                info->nand.read_buf   = omap_read_buf_pref;
                info->nand.write_buf  = omap_write_buf_pref;
-               if (use_dma) {
-                       err = omap_request_dma(OMAP24XX_DMA_GPMC, "NAND",
-                               omap_nand_dma_cb, &info->comp, &info->dma_ch);
-                       if (err < 0) {
-                               info->dma_ch = -1;
-                               printk(KERN_WARNING "DMA request failed."
-                                       " Non-dma data transfer mode\n");
-                       } else {
-                               omap_set_dma_dest_burst_mode(info->dma_ch,
-                                               OMAP_DMA_DATA_BURST_16);
-                               omap_set_dma_src_burst_mode(info->dma_ch,
-                                               OMAP_DMA_DATA_BURST_16);
-
-                               info->nand.read_buf   = omap_read_buf_dma_pref;
-                               info->nand.write_buf  = omap_write_buf_dma_pref;
-                       }
-               }
-       } else {
+               break;
+
+       case NAND_OMAP_POLLED:
                if (info->nand.options & NAND_BUSWIDTH_16) {
                        info->nand.read_buf   = omap_read_buf16;
                        info->nand.write_buf  = omap_write_buf16;
@@ -871,7 +826,33 @@ static int __devinit omap_nand_probe(struct 
platform_device *pdev)
                        info->nand.read_buf   = omap_read_buf8;
                        info->nand.write_buf  = omap_write_buf8;
                }
+               break;
+
+       case NAND_OMAP_PREFETCH_DMA:
+               err = omap_request_dma(OMAP24XX_DMA_GPMC, "NAND",
+                               omap_nand_dma_cb, &info->comp, &info->dma_ch);
+               if (err < 0) {
+                       info->dma_ch = -1;
+                       dev_err(&pdev->dev, "DMA request failed!\n");
+                       goto out_release_mem_region;
+               } else {
+                       omap_set_dma_dest_burst_mode(info->dma_ch,
+                                       OMAP_DMA_DATA_BURST_16);
+                       omap_set_dma_src_burst_mode(info->dma_ch,
+                                       OMAP_DMA_DATA_BURST_16);
+
+                       info->nand.read_buf   = omap_read_buf_dma_pref;
+                       info->nand.write_buf  = omap_write_buf_dma_pref;
+               }
+               break;
+
+       default:
+               dev_err(&pdev->dev,
+                       "xfer_type(%d) not supported!\n", pdata->xfer_type);
+               err = -EINVAL;
+               goto out_release_mem_region;
        }
+
        info->nand.verify_buf = omap_verify_buf;
 
 #ifdef CONFIG_MTD_NAND_OMAP_HWECC
@@ -897,6 +878,7 @@ static int __devinit omap_nand_probe(struct platform_device 
*pdev)
                }
        }
 
+
 #ifdef CONFIG_MTD_PARTITIONS
        err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0);
        if (err > 0)
@@ -926,7 +908,7 @@ static int omap_nand_remove(struct platform_device *pdev)
                                                        mtd);
 
        platform_set_drvdata(pdev, NULL);
-       if (use_dma)
+       if (info->dma_ch != -1)
                omap_free_dma(info->dma_ch);
 
        /* Release NAND device, its internal structures and partitions */
@@ -947,16 +929,8 @@ static struct platform_driver omap_nand_driver = {
 
 static int __init omap_nand_init(void)
 {
-       printk(KERN_INFO "%s driver initializing\n", DRIVER_NAME);
+       pr_info("%s driver initializing\n", DRIVER_NAME);
 
-       /* This check is required if driver is being
-        * loaded run time as a module
-        */
-       if ((1 == use_dma) && (0 == use_prefetch)) {
-               printk(KERN_INFO"Wrong parameters: 'use_dma' can not be 1 "
-                               "without use_prefetch'. Prefetch will not be"
-                               " used in either mode (mpu or dma)\n");
-       }
        return platform_driver_register(&omap_nand_driver);
 }
 
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to