Hi Sakari,
On Sun, May 13, 2012 at 7:24 PM, Sakari Ailus <sakari.ai...@iki.fi> wrote:
> Hi Sergio,
>
> On Thu, May 03, 2012 at 10:20:47PM -0500, Aguirre, Sergio wrote:
>> Hi Sakari,
>>
>> On Thu, May 3, 2012 at 7:03 AM, Aguirre, Sergio <saagui...@ti.com> wrote:
>> > Hi Sakari,
>> >
>> > Thanks for reviewing.
>> >
>> > On Wed, May 2, 2012 at 2:47 PM, Sakari Ailus <sakari.ai...@iki.fi> wrote:
>> >>
>> >> Hi Sergio,
>> >>
>> >> Thanks for the patches!!
>> >>
>> >> On Wed, May 02, 2012 at 10:15:46AM -0500, Sergio Aguirre wrote:
>> >> ...
>> >>> +static int sdp4430_ov_cam1_power(struct v4l2_subdev *subdev, int on)
>> >>> +{
>> >>> + struct device *dev = subdev->v4l2_dev->dev;
>> >>> + int ret;
>> >>> +
>> >>> + if (on) {
>> >>> + if (!regulator_is_enabled(sdp4430_cam2pwr_reg)) {
>> >>> + ret = regulator_enable(sdp4430_cam2pwr_reg);
>> >>> + if (ret) {
>> >>> + dev_err(dev,
>> >>> + "Error in enabling sensor power
>> >>> regulator 'cam2pwr'\n");
>> >>> + return ret;
>> >>> + }
>> >>> +
>> >>> + msleep(50);
>> >>> + }
>> >>> +
>> >>> + gpio_set_value(OMAP4430SDP_GPIO_CAM_PDN_B, 1);
>> >>> + msleep(10);
>> >>> + ret = clk_enable(sdp4430_cam1_aux_clk); /* Enable XCLK */
>> >>> + if (ret) {
>> >>> + dev_err(dev,
>> >>> + "Error in clk_enable() in %s(%d)\n",
>> >>> + __func__, on);
>> >>> + gpio_set_value(OMAP4430SDP_GPIO_CAM_PDN_B, 0);
>> >>> + return ret;
>> >>> + }
>> >>> + msleep(10);
>> >>> + } else {
>> >>> + clk_disable(sdp4430_cam1_aux_clk);
>> >>> + msleep(1);
>> >>> + gpio_set_value(OMAP4430SDP_GPIO_CAM_PDN_B, 0);
>> >>> + if (regulator_is_enabled(sdp4430_cam2pwr_reg)) {
>> >>> + ret = regulator_disable(sdp4430_cam2pwr_reg);
>> >>> + if (ret) {
>> >>> + dev_err(dev,
>> >>> + "Error in disabling sensor power
>> >>> regulator 'cam2pwr'\n");
>> >>> + return ret;
>> >>> + }
>> >>> + }
>> >>> + }
>> >>> +
>> >>> + return 0;
>> >>> +}
>> >>
>> >> Isn't this something that should be part of the sensor driver? There's
>> >> nothing in the above code that would be board specific, except the names
>> >> of
>> >> the clocks, regulators and GPIOs. The sensor driver could hold the names
>> >> instead; this would be also compatible with the device tree.
>> >
>> > Agreed. I see what you mean...
>> >
>> > I'll take care of that.
>>
>> Can you please check out these patches?
>>
>> 1.
>> http://gitorious.org/omap4-v4l2-camera/omap4-v4l2-camera/commit/cb6c10d58053180364461e6bc8d30d1ec87e6e22
>
> Ideally we should really get rid of the board code callbacks. What do you
> need to do there?
Well, in a OMAP44xx Blaze:
http://svtronics.com/products/27-blaze-mdp
The CSI2-A interface has 2 possible sensor inputs:
- Sony IMX060 12 MP
- OmniVision OV5650 5MP
Which are muxed with a High speed differential selector.
(Analog devices part: ADG936, found here:
http://www.analog.com/static/imported-files/data_sheets/ADG936_936R.pdf)
And to make it more fun, you switch that with a GPIO in an Audio IC (TWL6040) !
Quite a mess, but leaves me with few options, so that's why I need
that to be board
specific, and that by providing these function that can be used to
take care of such
"creative" designs :P
Have better ideas?
>
>> 2.
>> http://gitorious.org/omap4-v4l2-camera/omap4-v4l2-camera/commit/6732e0db25c6647b34ef8f01c244a49a1fd6b45d
>
> Isn't reset voltage level (high or low) a property of the sensor rather than
> the board?
>
> Well, I know sometimes the people who typically design the hardware can be
> quite inventive. ;)
Unfortunately, that's exactly the case!
Again, in this "creative" design in Blaze platform I mentioned above,
they also have a
level inverter just before the RESET pin in the sensor. So that makes
it active high, from
the GPIO driver point of view :/
Not sure if there's a better way of handling this...
Thanks for the comments!
Regards,
Sergio
>
>> 3.
>> http://gitorious.org/omap4-v4l2-camera/omap4-v4l2-camera/commit/d61c4e3142dc9cae972f9128fe73d986838c0ca1
>
>> 4.
>> http://gitorious.org/omap4-v4l2-camera/omap4-v4l2-camera/commit/e83f36001c7f7cbe184ad094d9b0c95c39e5028f
>
> Cheers,
>
> --
> Sakari Ailus
> e-mail: sakari.ai...@iki.fi jabber/XMPP/Gmail: sai...@retiisi.org.uk
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
