On 2015년 12월 10일 11:04, Krzysztof Kozlowski wrote:
> On 10.12.2015 11:00, Chanwoo Choi wrote:
>> On 2015년 12월 10일 10:20, Krzysztof Kozlowski wrote:
>>> On 10.12.2015 10:09, Chanwoo Choi wrote:
>>>> On 2015년 12월 10일 09:44, Krzysztof Kozlowski wrote:
>>>>> On 09.12.2015 13:07, Chanwoo Choi wrote:
>>>>>> This patch adds the DMC (Dynamic Memory Controller) bus node for
>>>>>> Exynos3250 SoC.
>>>>>> The DMC is an AMBA AXI-compliant slave to interface external JEDEC
>>>>>> standard
>>>>>> SDRAM devices. The bus includes the OPP tables and the source clock for
>>>>>> DMC
>>>>>> block.
>>>>>>
>>>>>> Following list specifies the detailed relation between the clock and DMC
>>>>>> block:
>>>>>> - The source clock of DMC block : div_dmc
>>>>>>
>>>>>> Signed-off-by: Chanwoo Choi <cw00.c...@samsung.com>
>>>>>> ---
>>>>>> arch/arm/boot/dts/exynos3250.dtsi | 34
>>>>>> ++++++++++++++++++++++++++++++++++
>>>>>> 1 file changed, 34 insertions(+)
>>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/exynos3250.dtsi
>>>>>> b/arch/arm/boot/dts/exynos3250.dtsi
>>>>>> index 2f30d632f1cc..7214c5e42150 100644
>>>>>> --- a/arch/arm/boot/dts/exynos3250.dtsi
>>>>>> +++ b/arch/arm/boot/dts/exynos3250.dtsi
>>>>>> @@ -687,6 +687,40 @@
>>>>>> clock-names = "ppmu";
>>>>>> status = "disabled";
>>>>>> };
>>>>>> +
>>>>>> + bus_dmc: bus_dmc {
>>>>>> + compatible = "samsung,exynos-bus";
>>>>>> + clocks = <&cmu_dmc CLK_DIV_DMC>;
>>>>>> + clock-names = "bus";
>>>>>> + operating-points-v2 = <&bus_dmc_opp_table>;
>>>>>> + status = "disabled";
>>>>>> + };
>>>>>> +
>>>>>> + bus_dmc_opp_table: opp_table1 {
>>>>>
>>>>> This is the firsy opp_table, right? So:
>>>>> s/opp_table1/opp_table0/
>>>>
>>>> Right. It is first opp_table in exynos3250.dtsi.
>>>> But, I'm considering the OPP table of CPU freqeuncy as opp_table0.
>>>> So, I have the plan that support the operation-points-v2 for Exynos3250
>>>> CPU.
>>>
>>> Ok
>>>
>>>>
>>>>>
>>>>>> + compatible = "operating-points-v2";
>>>>>> + opp-shared;
>>>>>> +
>>>>>> + opp00 {
>>>>>> + opp-hz = /bits/ 64 <50000000>;
>>>>>> + opp-microvolt = <800000>;
>>>>>> + };
>>>>>> + opp01 {
>>>>>> + opp-hz = /bits/ 64 <100000000>;
>>>>>> + opp-microvolt = <800000>;
>>>>>> + };
>>>>>> + opp02 {
>>>>>> + opp-hz = /bits/ 64 <134000000>;
>>>>>> + opp-microvolt = <800000>;
>>>>>
>>>>> Why 134, not 133 MHz?
>>>>
>>>> When I used the 133000000, the source clock is changed to 100Mhz instead
>>>> of 133MHz.
>>>> I add following test result on exynos3250-rinato board.
>>>>
>>>> Case1.
>>>> When I use the 134 MHz, the source clock is changed to 133MHz
>>>> : exynos-bus soc:bus_dmc: old_freq(200000000) -> new_freq (134000000)
>>>> (real: 133333334)
>>>>
>>>> Case2.
>>>> When I use the 133 MHz, the source clock is changed to 100MHz
>>>> : exynos-bus soc:bus_dmc: old_freq(200000000) -> new_freq (133000000)
>>>> (real: 100000000)
>>>
>>> Now I remember that issue. You could use here directly 133333334 but
>>> that also would look a little bit weird... so 134 is ok for me. Could
>>> just add a comment that desired frequency is actually "133 MHz"?
>>
>> Do you prefer among following example?
>>
>> Example1.
>> opp02 {
>> /* The desired frequency is 133MHz because
>> * clock change has the dependency on clock driver.
>> * When set rate as 134MHz, the clock driver would
>> * change the 133MHz actually instead of 134MHz.
>> */
>> opp-hz = /bits/ 64 <134000000>;
>> opp-microvolt = <800000>;
>> };
>>
>> Example2.
>> opp02 {
>> opp-hz = /bits/ 64 <133333334>;
>> opp-microvolt = <800000>;
>> };
>
> I would prefer the second one (133333334) but I don't have strong
> feelings about it.
If you ok, I want to maintain the original approach as following:
opp02 {
opp-hz = /bits/ 64 <134000000>;
opp-microvolt = <800000>;
};
Best Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
