On 12/04/2012 05:00 PM, Chris Friesen wrote:
On 12/03/2012 03:53 PM, Ric Wheeler wrote:
On 12/03/2012 04:08 PM, Chris Friesen wrote:
On 12/03/2012 02:52 PM, Ric Wheeler wrote:
I jumped into this thread late - can you repost detail on the specific
drive and HBA used here? In any case, it sounds like this is a better
topic for the linux-scsi or linux-ide list where most of the low level
storage people lurk :)
Okay, expanding the receiver list. :)
To recap:
I'm running 2.6.27 with LVM over software RAID 1 over a pair of SAS
disks.
Disks are WD9001BKHG, controller is Intel C600.
Recently we started seeing messages of the following pattern, and we
don't know what's causing them:
Nov 28 08:57:10 kernel: end_request: I/O error, dev sda, sector
1758169523
Nov 28 08:57:10 kernel: md: super_written gets error=-5, uptodate=0
Nov 28 08:57:10 kernel: raid1: Disk failure on sda2, disabling device.
Nov 28 08:57:10 kernel: raid1: Operation continuing on 1 devices.
We've been assuming it's a software issue since it's reproducible on
multiple systems, although so far we've only seen the problem with
these particular disks.
We've seen the problems with disk write cache enabled and disabled.
Hi Chris,
Are there any earlier IO errors or sda related errors in the log?
Nope, at least not nearby. On one system for instance we boot up and
get into steady-state, then there are no kernel logs for about half an
hour then out of the blue we see:
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: end_request: I/O error, dev sda,
sector 1758169523
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: md: super_written gets error=-5,
uptodate=0
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: raid1: Disk failure on sda2,
disabling device.
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: raid1: Operation continuing on 1
devices.
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: end_request: I/O error, dev sdb,
sector 1758169523
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: md: super_written gets error=-5,
uptodate=0
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: RAID1 conf printout:
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: --- wd:1 rd:2
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: disk 0, wo:1, o:0, dev:sda2
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: disk 1, wo:0, o:1, dev:sdb2
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: RAID1 conf printout:
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: --- wd:1 rd:2
Nov 27 14:58:13 base0-0-0-13-0-11-1 kernel: disk 1, wo:0, o:1, dev:sdb2
As another data point, it looks like we may be doing a SEND DIAGNOSTIC
command specifying the default self-test in addition to the background
short self-test. This seems a bit risky and excessive to me, but
apparently the guy that wrote it is no longer with the company.
What is the recommended method for monitoring disks on a system that
is likely to go a long time between boots? Do we avoid any in-service
testing and just monitor the SMART data and only test it if something
actually goes wrong? Or should we intentionally drop a disk out of the
array and test it? (The downside of that is that we lose
redundancy since we only have 2 disks.)
Chris
I don't know if running the self tests really helps. Normally, I would simply
suggest scanning for remapped sectors (and looking out for lots of them, not
just a handful since they are moderately normal in disks). You can do that with
smartctl.
Best advice is to try and consult directly with your disk vendor about their
suggestions if you have that connection of course :)
Ric
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
