Make sure the usb-ethernet is connected BEFORE you load the driver -- or
try rmmod'ing the driver and insmod'ing it again.
RBM
On 9 Jun, hashimoh wrote:
> I also am trying to use my ATEM Ethernet USB
>
> Adaptor.
>
> I am now applying Micheal's kaweth driver
>
> 0.2.1(thank you). But I failed to recognize.
>
> Here is a output of dmesg and contents of
>
> /proc/bus/usb/devices
>
> Any suggestions are welcome.
>
> Thanks.
>
> Hisashi
>
> PS.
>
> In my environment, order of 'insmod', pluggin device
>
> does not have any effect to recognition.
>
> ---------------------------
>
> Envirionment Kernel 2.2.14 + backport patch usb-2.3.99-pre7-1-for-2.2.14.diff.gz
>
> output of dmesg(only related parts)
>
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> usb-uhci.c: $Revision: 1.228 $ time 23:03:48 May 12 2000
> usb-uhci.c: High bandwidth mode enabled
> usb-uhci.c: Intel USB controller: setting latency timer to 0
> usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 10
> usb-uhci.c: Detected 2 ports
> usb.c: new USB bus registered, assigned bus number 1
> usb.c: USB new device connect, assigned device number 1
> usb.c: kmalloc IF c0e0bb20, numif 1
> usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
> usb.c: USB device number 1 default language ID 0x0
> Product: USB UHCI Root Hub
> SerialNumber: fce0
> hub.c: USB hub found
> hub.c: 2 ports detected
> hub.c: ganged power switching
> hub.c: standalone hub
> hub.c: global over-current protection
> hub.c: power on to power good time: 2ms
> hub.c: hub controller current requirement: 0mA
> hub.c: port 1 is removable
> hub.c: port 2 is removable
> hub.c: local power source is good
> hub.c: no over-current condition exists
> hub.c: enabling power on all ports
> usb.c: hub driver claimed interface c0e0bb20
> Kawasaki USB->Ethernet Driver loading...
> usb.c: registered new driver kaweth
> usb.c: registered new driver hid
> mice: PS/2 mouse device common for all mice
> usb.c: registered new driver usblp
> registered device ppp0
> hub.c: port 1 connection change
> hub.c: portstatus 101, change 1, High Speed
> hub.c: portstatus 103, change 0, High Speed
> usb.c: USB new device connect, assigned device number 2
> usb.c: kmalloc IF c2c0a3c0, numif 1
> usb.c: new device strings: Mfr=2, Product=3, SerialNumber=1
> usb.c: USB device number 2 default language ID 0x409
> Manufacturer: ATEN Inc.
> Product: USB-Ethernet
> SerialNumber: 001074003548
> usb-uhci.c: interrupt, status 2, frame# 1844
> Kawasaki Device Probe (Device number:2): 0x0557:0x2002
> Device at c1871b40
> Descriptor length: 12 type: 1
> D-Link DSB-650 connected...
> Reading kaweth configuration
> Request type: c0 Request: 0 Value: 0 Index: 0 Length: 12
> usb-uhci.c: interrupt, status 2, frame# 1846
> usb-uhci-debug.h: TD @ c0d4b8e0/00D4B8E0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0440
> usb-uhci-debug.h: Len=07 e0 Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4b9e0, Breadth first
> kaweth control message failed (urb addr: c0f97d20)
> usb-uhci.c: interrupt, status 2, frame# 1849
> usb-uhci-debug.h: TD @ c0d4b860/00D4B860, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
> usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4ba20, Breadth first
> usb-uhci.c: interrupt, status 2, frame# 1851
> usb-uhci-debug.h: TD @ c0d4b960/00D4B960, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
> usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4b7e0, Breadth first
> Actual length: 0, length 18
> Resetting...
> usb-uhci.c: interrupt, status 2, frame# 1854
> usb-uhci-debug.h: TD @ c0d4ba20/00D4BA20, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0440
> usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4b860, Breadth first
> Downloading firmware at c38a4ab8 to kaweth device at c1794000...
> Firmware length: 3838
> Request type: 40 Request: ff Value: 0 Index: 0 Length: efe
> usb-uhci.c: interrupt, status 2, frame# 1868
> usb-uhci-debug.h: TD @ c0d4b7e0/00D4B7E0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0440
> usb-uhci-debug.h: Len=07 e0 Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4b960, Breadth first
> kaweth control message failed (urb addr: c0f97d20)
> usb-uhci.c: interrupt, status 2, frame# 1870
> usb-uhci-debug.h: TD @ c0d4b860/00D4B860, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
> usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4ba20, Breadth first
> usb-uhci.c: interrupt, status 2, frame# 1873
> usb-uhci-debug.h: TD @ c0d4bfa0/00D4BFA0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
> usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
> usb-uhci-debug.h: Link points to TD @ 00d4bf60, Breadth first
> Actual length: 0, length 3838
> Error downloading firmware (-110), no net device created
> usb.c: unhandled interfaces on device
> usb.c: This device is not recognized by any installed USB driver.
> Length = 18
> DescriptorType = 01
> USB version = 1.00
> Vendor:Product = 0557:2002
> MaxPacketSize0 = 8
> NumConfigurations = 1
> Device version = 0.02
> Device Class:SubClass:Protocol = 00:00:00
> Per-interface classes
> Configuration:
> bLength = 9
> bDescriptorType = 02
> wTotalLength = 0027
> bNumInterfaces = 01
> bConfigurationValue = 01
> iConfiguration = 00
> bmAttributes = 80
> MaxPower = 90mA
>
> Interface: 0
> Alternate Setting: 0
> bLength = 9
> bDescriptorType = 04
> bInterfaceNumber = 00
> bAlternateSetting = 00
> bNumEndpoints = 03
> bInterface Class:SubClass:Protocol = 00:00:00
> iInterface = 00
> Endpoint:
> bLength = 7
> bDescriptorType = 05
> bEndpointAddress = 81 (in)
> bmAttributes = 02 (Bulk)
> wMaxPacketSize = 0040
> bInterval = 00
> Endpoint:
> bLength = 7
> bDescriptorType = 05
> bEndpointAddress = 02 (out)
> bmAttributes = 02 (Bulk)
> wMaxPacketSize = 0040
> bInterval = 00
> Endpoint:
> bLength = 7
> bDescriptorType = 05
> bEndpointAddress = 83 (in)
> bmAttributes = 03 (Interrupt)
> wMaxPacketSize = 0008
> bInterval = 01
> ---------------------------------------------------------
>
> contents of /proc/bus/usb/devices
>
> T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
> D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=0000 ProdID=0000 Rev= 0.00
> S: Product=USB UHCI Root Hub
> S: SerialNumber=fce0
> C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
> D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=0557 ProdID=2002 Rev= 0.02
> C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 90mA
> I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=(none)
> E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
> E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl= 1ms
>
> --
> ---------------------------------
> Hashimoto Hisashi(Hitachi@HP NJL)
> [EMAIL PROTECTED]
> ---------------------------------
>
>
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
>
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
