http://en.wikipedia.org/wiki/Ext2ext2From Wikipedia, the free encyclopedia
The ext2 or second extended filesystem is a file system for the Linux kernel. It was initially designed by Rémy Card as a replacement for the extended file system (ext). Although ext2 is not a journaling file system, its successor, ext3, provides journaling and is almost completely compatible with ext2. The canonical implementation of ext2 is the ext2fs filesystem driver in the Linux kernel. Other implementations (of varying quality and completeness) exist in GNU Hurd, Mac OS X (third-party), Darwin (same third-party as Mac OS X but untested), some BSD kernels, in Atari MiNT, and as third-party Microsoft Windows drivers. ext2 was the default filesystem in several Linux distributions, including Debian and Red Hat Linux, until supplanted more recently by ext3.
[edit] HistoryThe early development of the Linux kernel was made as a cross-development under the Minix operating system. Naturally, it was obvious that the Minix file system would be used as Linux's first file system. The Minix file system was mostly free of bugs, but used 16-bit offsets internally and thus only had a maximum size limit of 64 megabytes. There was also a filename length limit of 14 characters. Because of these limitations, work began on a replacement native file system for Linux. To ease the addition of new file systems and provide a generic file API, VFS, a virtual file system layer was added to the Linux kernel. The extended file system (ext), was released in April 1992 as the first file system using the VFS API and was included in Linux version 0.96c. The ext file system solved the two major problems in the Minix file system (maximum partition size and filename length limitation to 14 characters), and allowed 2 gigabytes of data and filenames of up to 255 characters. But it still had problems: there was no support for separate access, inode modification and data modification timestamps. As a solution for these problems, two new filesystems were developed in January 1993: xiafs and the second extended file system (ext2), which was an overhaul of the extended file system incorporating many ideas from the Berkeley Fast File System. ext2 was also designed with extensibility in mind, with space left in many of its on-disk data structures for use by future versions. Since then, ext2 has been a testbed for many of the new extensions to the VFS API. Features such as POSIX ACLs and extended attributes were generally implemented first on ext2 because it was relatively simple to extend and its internals were well-understood. On Linux kernels prior to 2.6, restrictions in the block driver mean that ext2 filesystems have a maximum file size of 2TiB. Later Linux kernels allow for larger file sizes, however 32-bit systems are still restricted to 2 TiB file sizes. ext2 is still recommended over journaling file systems on bootable USB flash drives and other solid-state drives. ext2 performs fewer writes than ext3 since it does not need to write to the journal. As the major aging factor of a flash chip is the number of erase cycles, and as those happen frequently on writes, this increases the life span of the solid-state device.[1] Another good practice for filesystems on flash devices is the use of the noatime mount option, for the same reason. [edit] ext2 data structuresThe space in ext2 is split up in blocks, and organized into block groups, analogous to cylinder groups in the Unix File System. This is done to reduce external fragmentation and minimize the number of disk seeks when reading a large amount of consecutive data. Each block group may contain a copy of the superblock and block group descriptor table, and all block groups contain a block bitmap, an inode bitmap, an inode table and followed by the actual data blocks. The superblock contains important information that is crucial to the booting of the operating system, thus backup copies are made in multiple block groups in the file system. However, typically only the first copy of it, which is found at the first block of the file system, is used in the booting. The group descriptor stores the location of the block bitmap, inode bitmap and the start of the inode table for every block group and these, in turn are stored in a group descriptor table.
 [edit] File system limits
The reason for some limits of the ext2-file system are the file format of the data and the operating system's kernel. Mostly these factors will be determined once when the file system is built. They depend on the block size and the ratio of the number of blocks and inodes. In Linux the block size is limited by the architecture page size. There are also many userspace programs that can't handle files larger than 2 GB. The limit of sublevel-directories is about 32768. If the number of files in a directory exceeds 10000 to 15000 files, the user will normally be warned that operations can last for a long time unless directory indexing is enabled. The theoretical limit on the number of files in a directory is 1.3 × 1020, although this is not relevant for practical situations. [edit] See also
[edit] References
[edit] Further reading
[edit] External links
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
